If you are using the current version of Cumulus Linux, the content on this page may not be up to date. The current version of the documentation is available here. If you are redirected to the main page of the user guide, then this page may have been renamed; please search for it there.

Equal Cost Multipath Load Sharing - Hardware ECMP

Cumulus Linux supports hardware-based equal cost multipath (ECMP) load sharing. ECMP is enabled by default in Cumulus Linux. Load sharing occurs automatically for all routes with multiple next hops installed. ECMP load sharing supports both IPv4 and IPv6 routes.

Equal Cost Routing

ECMP operates only on equal cost routes in the Linux routing table.

In this example, the 10.1.1.0/24 route has two possible next hops that have been installed in the routing table:

cumulus@switch:~$ ip route show 10.1.1.0/24
10.1.1.0/24  proto zebra  metric 20
  nexthop via 192.168.1.1 dev swp1 weight 1 onlink
  nexthop via 192.168.2.1 dev swp2 weight 1 onlink

For routes to be considered equal they must:

  • Originate from the same routing protocol. Routes from different sources are not considered equal. For example, a static route and an OSPF route are not considered for ECMP load sharing.
  • Have equal cost. If two routes from the same protocol are unequal, only the best route is installed in the routing table.

In Cumulus Linux, the BGP maximum-paths setting is enabled, so multiple routes are installed by default. See ECMP under BGP for more information.

ECMP Hashing

When multiple routes are installed in the routing table, a hash is used to determine which path a packet follows.

Cumulus Linux hashes on the following fields:

  • IP protocol
  • Ingress interface
  • Source IPv4 or IPv6 address
  • Destination IPv4 or IPv6 address

Further, on switches with Spectrum ASICs, Cumulus Linux hashes on these additional fields:

  • Source MAC address
  • Destination MAC address
  • Ethertype
  • VLAN ID

For TCP/UDP frames, Cumulus Linux also hashes on:

  • Source port
  • Destination port

To prevent out of order packets, ECMP hashing is done on a per-flow basis; all packets with the same source and destination IP addresses and the same source and destination ports always hash to the same next hop. ECMP hashing does not keep a record of flow states.

ECMP hashing does not keep a record of packets that have hashed to each next hop and does not guarantee that traffic sent to each next hop is equal.

Use cl-ecmpcalc to Determine the Hash Result

Because the hash is deterministic and always provides the same result for the same input, you can query the hardware and determine the hash result of a given input. This is useful when determining exactly which path a flow takes through a network.

On Cumulus Linux, use the cl-ecmpcalc command to determine a hardware hash result.

To use cl-ecmpcalc, all fields that are used in the hash must be provided. This includes ingress interface, layer 3 source IP, layer 3 destination IP, layer 4 source port, and layer 4 destination port.

cumulus@switch:~$ sudo cl-ecmpcalc -i swp1 -s 10.0.0.1 -d 10.0.0.1 -p tcp --sport 20000 --dport 80
ecmpcalc: will query hardware
swp3

If any field is omitted, cl-ecmpcalc fails.

cumulus@switch:~$ sudo cl-ecmpcalc -i swp1 -s 10.0.0.1 -d 10.0.0.1 -p tcp
ecmpcalc: will query hardware
usage: cl-ecmpcalc [-h] [-v] [-p PROTOCOL] [-s SRC] [--sport SPORT] [-d DST]
                   [--dport DPORT] [--vid VID] [-i IN_INTERFACE]
                   [--sportid SPORTID] [--smodid SMODID] [-o OUT_INTERFACE]
                   [--dportid DPORTID] [--dmodid DMODID] [--hardware]
                   [--nohardware] [-hs HASHSEED]
                   [-hf HASHFIELDS [HASHFIELDS ...]]
                   [--hashfunction {crc16-ccitt,crc16-bisync}] [-e EGRESS]
                   [-c MCOUNT]
cl-ecmpcalc: error: --sport and --dport required for TCP and UDP frames

cl-ecmpcalc Limitations

cl-ecmpcalc can only take input interfaces that can be converted to a single physical port in the port tab file, such as the physical switch ports (swp). Virtual interfaces like bridges, bonds, and subinterfaces are not supported.

cl-ecmpcalc is supported only on switches with the Mellanox Spectrum and the Broadcom Maverick, Tomahawk, Trident II, Trident II+ and Trident3 chipsets.

ECMP Hash Buckets

When multiple routes are installed in the routing table, each route is assigned to an ECMP bucket. When the ECMP hash is executed the result of the hash determines which bucket gets used.

In the following example, four next hops exist. Three different flows are hashed to different hash buckets. Each next hop is assigned to a unique hash bucket.

Add a Next Hop

When a next hop is added, a new hash bucket is created. The assignment of next hops to hash buckets, as well as the hash result, might change when additional next hops are added.

A new next hop is added and a new hash bucket is created. As a result, the hash and hash bucket assignment changes, causing the existing flows to be sent to different next hops.

Remove a Next Hop

When a next hop is removed, the remaining hash bucket assignments might change, again, potentially changing the next hop selected for an existing flow.

A next hop fails and the next hop and hash bucket are removed. The remaining next hops might be reassigned.

In most cases, the modification of hash buckets has no impact on traffic flows as traffic is being forwarded to a single end host. In deployments where multiple end hosts are using the same IP address (anycast), resilient hashing must be used.

Configure a Hash Seed to Avoid Hash Polarization

It is useful to have a unique hash seed for each switch. This helps avoid hash polarization, a type of network congestion that occurs when multiple data flows try to reach a switch using the same switch ports.

The hash seed is set by the ecmp_hash_seed parameter in the /etc/cumulus/datapath/traffic.conf file. It is an integer with a value from 0 to 4294967295. If you do not specify a value, switchd creates a randomly generated seed instead.

For example, to set the hash seed to 50, run the following commands:

cumulus@switch:~$ net add forwarding ecmp hash-seed 50
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

Edit /etc/cumulus/datapath/traffic.conf file. For example:

cumulus@switch:~$ sudo nano /etc/cumulus/datapath/traffic.conf
...
#Specify the hash seed for Equal cost multipath entries
ecmp_hash_seed = 50
...

Restart the switchd service:

cumulus@switch:~$ sudo systemctl restart switchd.service

ECMP Custom Hashing

Custom hashing is supported on Mellanox switches.

You can configure the set of fields used to hash upon during ECMP load balancing. For example, if you do not want to use source or destination port numbers in the hash calculation, you can disable the source port and destination port fields.

You can enable/disable the following fields:

  • IP Protocol
  • Source IP
  • Destination IP
  • Source port
  • Destination port
  • IPv6 flow label
  • Ingress interface

You can also enable/disable these Inner header fields:

  • Inner IP protocol
  • Inner source IP
  • Inner destination IP
  • Inner source port
  • Inner destination port
  • Inner IPv6 flow label

To configure custom hashing, edit the /usr/lib/python2.7/dist-packages/cumulus/__chip_config/mlx/datapath.conf file:

  1. To enable custom hashing, uncomment the hash_config.enable = true line.

  2. To enable a field, set the field to true. To disable a field, set the field to false.

  3. Restart the switchd service:

    cumulus@switch:~$ sudo systemctl restart switchd.service
    

The following shows an example datapath.conf file:

cumulus@switch:~$ sudo nano /usr/lib/python2.7/dist-packages/cumulus/__chip_config/mlx/datapath.conf
...
# HASH config for ECMP to enable custom fields
# Fields will be applicable for ECMP hash
# calculation
#Note: Hash seed can be configured in traffic.conf
#/etc/cumulus/datapath/traffic.conf
#
# Uncomment to enable custom fields configured below
hash_config.enable = true

#symmetric hash will get disabled
#if sip/dip or sport/dport are not enabled in pair
#hash Fields available ( assign true to enable)
#ip protocol
hash_config.ip_prot = true
#source ip
hash_config.sip = true
#destination ip
hash_config.dip = true
#source port
hash_config.sport = false
#destination port
hash_config.dport = false
#ipv6 flow label
hash_config.ip6_label = true
#ingress interface
hash_config.ing_intf = false

#inner fields for  IPv4-over-IPv6 and IPv6-over-IPv6
hash_config.inner_ip_prot = false
hash_config.inner_sip = false
hash_config.inner_dip = false
hash_config.inner_sport = false
hash_config.inner_dport = false
hash_config.inner_ip6_label = false
# Hash config end #
...

Symmetric hashing is enabled by default on Mellanox switches. Make sure that the settings for the source IP (hash_config.sip) and destination IP (hash_config.dip) fields match, and that the settings for the source port (hash_config.sport) and destination port (hash_config.dport) fields match; otherwise symmetric hashing is disabled automatically. You can disable symmetric hashing manually in the /etc/cumulus/datapath/traffic.conf file by setting symmetric_hash_enable = FALSE.

Resilient Hashing

In Cumulus Linux, when a next hop fails or is removed from an ECMP pool, the hashing or hash bucket assignment can change. For deployments where there is a need for flows to always use the same next hop, like TCP anycast deployments, this can create session failures.

Resilient hashing is an alternate mechanism for managing ECMP groups. The ECMP hash performed with resilient hashing is exactly the same as the default hashing mode. Only the method in which next hops are assigned to hash buckets differs — they’re assigned to buckets by hashing their header fields and using the resulting hash to index into the table of 2^n hash buckets. Since all packets in a given flow have the same header hash value, they all use the same flow bucket.

Resilient hashing supports both IPv4 and IPv6 routes.

Resilient hashing behaves slightly differently depending upon whether you are running Cumulus Linux on a switch with a Broadcom ASIC or Mellanox ASIC. The differences are described below.

Resilient hashing is not enabled by default. See below for steps on configuring it.

Resilient Hashing on Broadcom Switches

Resilient hashing is supported only on switches with the Broadcom Tomahawk, Trident II, Trident II+, and Trident3 ASICs. You can run net show system to determine the ASIC.

The Broadcom ASIC assigns packets to hash buckets and assigns hash buckets to next hops as follows:

  • When a next hop is removed, the assigned buckets are distributed to the remaining next hops.
  • When a next hop is added, some buckets assigned to other next hops are migrated to the new next hop.
  • The algorithm assigns buckets to next hops so as to make the number of buckets per next hop as close to equal as possible.
  • The assignment of buckets to next hops is not changed in any other case. In particular, this assignment is not changed due to traffic loading or imbalance.
  • Next hops are assigned to buckets randomly, to minimize the chance of systemic imbalance.

Resilient Hashing on Mellanox Switches

A Mellanox switch has two unique options for configuring resilient hashing, both of which you configure in the /usr/lib/python2.7/dist-packages/cumulus/__chip_config/mlx/datapath.conf​ file. The recommended values for these options depend largely on the desired outcome for a specific network implementation — the number and duration of flows, and the importance of keeping these flows pinned without interruption.

  • resilient_hash_active_timer: A timer that protects TCP sessions from being disrupted while attempting to populate new next hops. You specify the number of seconds when at least one hash bucket consistently sees no traffic before Cumulus Linux rebalances the flows; the default is 120 seconds. If any one bucket is idle; that is, it sees no traffic for the defined period, the next new flow utilizes that bucket and flows to the new link. Thus, if the network is experiencing a large number of flows or very consistent or persistent flows, there may not be any buckets remaining idle for a consistent 120 second period, and the imbalance remains until that timer has been met. If a new link is brought up and added back to a group during this time, traffic does not get allocated to utilize it until a bucket qualifies as empty, meaning it has been idle for 120 seconds. This is when a rebalance can occur.
  • resilient_hash_max_unbalanced_timer: You can force a rebalance every N seconds with this option. However, while this could correct the persistent imbalance that is expected with resilient hashing, this rebalance would result in the movement of all flows and thus a break in any TCP sessions that are active at that time.

Note that when you configure these options, a new next hop might not get populated for a long time.

The Mellanox Spectrum ASIC assigns packets to hash buckets and assigns hash buckets to next hops as follows. It also runs a background thread that monitors and may migrate buckets between next hops to rebalance the load.

  • When a next hop is removed, the assigned buckets are distributed to the remaining next hops.
  • When a next hop is added, no buckets are assigned to the new next hop until the background thread rebalances the load.
  • The load gets rebalanced when the active flow timer specified by the resilient_hash_active_timer setting expires if, and only if, there are inactive hash buckets available; the new next hop may remain unpopulated until the period set in resilient_hash_active_timer expires
  • When the resilient_hash_max_unbalanced_timer setting expires and the load is not balanced, the thread migrates any bucket(s) to different next hops to rebalance the load.

As a result, any flow may be migrated to any next hop, depending on flow activity and load balance conditions; over time, the flow may get pinned, which is the default setting and behavior.

Resilient Hash Buckets

When resilient hashing is configured, a fixed number of buckets are defined. Next hops are then assigned in round robin fashion to each of those buckets. In this example, 12 buckets are created and four next hops are assigned.

Remove Next Hops

Unlike default ECMP hashing, when a next hop needs to be removed, the number of hash buckets does not change.

With 12 buckets assigned and four next hops, instead of reducing the number of buckets - which would impact flows to known good hosts - the remaining next hops replace the failed next hop.

After the failed next hop is removed, the remaining next hops are installed as replacements. This prevents impact to any flows that hash to working next hops.

Add Next Hops

Resilient hashing does not prevent possible impact to existing flows when new next hops are added. Due to the fact there are a fixed number of buckets, a new next hop requires reassigning next hops to buckets.

As a result, some flows may hash to new next hops, which can impact anycast deployments.

Configure Resilient Hashing

Resilient hashing is not enabled by default. When resilient hashing is enabled, 65,536 buckets are created to be shared among all ECMP groups. An ECMP group is a list of unique next hops that are referenced by multiple ECMP routes.

An ECMP route counts as a single route with multiple next hops. The following example is considered to be a single ECMP route:

cumulus@switch:~$ ip route show 10.1.1.0/24
10.1.1.0/24  proto zebra  metric 20
  nexthop via 192.168.1.1 dev swp1 weight 1 onlink
  nexthop via 192.168.2.1 dev swp2 weight 1 onlink

All ECMP routes must use the same number of buckets (the number of buckets cannot be configured per ECMP route).

The number of buckets can be configured as 64, 128, 256, 512 or 1024; the default is 128:

Number of Hash BucketsNumber of Supported ECMP Groups
641024
128512
256256
512128
102464

Mellanox switches with the Spectrum ASIC do not support 128 or 256 hash buckets. The default number of hash buckets is 64.

A larger number of ECMP buckets reduces the impact on adding new next hops to an ECMP route. However, the system supports fewer ECMP routes. If the maximum number of ECMP routes have been installed, new ECMP routes log an error and are not installed.

To enable resilient hashing, edit /etc/cumulus/datapath/traffic.conf:

  1. Enable resilient hashing:

    # Enable resilient hashing
    resilient_hash_enable = TRUE
    
  2. (Optional) Edit the number of hash buckets:

    # Resilient hashing flowset entries per ECMP group
    # Valid values - 64, 128, 256, 512, 1024
    resilient_hash_entries_ecmp = 256
    
  3. Restart the switchd service:

    cumulus@switch:~$ sudo systemctl restart switchd.service
    

Caveats and Errata

IPv6 Route Replacement

When the next hop information for an IPv6 prefix changes (for example, when ECMP paths are added or deleted, or when the next hop IP address, interface, or tunnel changes), FRR deletes the existing route to that prefix from the kernel and then adds a new route with all the relevant new information. Because of this process, resilient hashing might not be maintained for IPv6 flows in certain situations.

To work around this issue, you can enable the IPv6 route replacement option.

Be aware that for certain configurations, the IPv6 route replacement option can lead to incorrect forwarding decisions and lost traffic. For example, it is possible for a destination to have next hops with a gateway value with the outbound interface or just the outbound interface itself, without a gateway address defined. If both types of next hops for the same destination exist, route replacement does not operate correctly; Cumulus Linux adds an additional route entry and next hop but does not delete the previous route entry and next hop.

To enable the IPv6 route replacement option:

  1. In the /etc/frr/daemons file, add the configuration option --v6-rr-semantics to the zebra daemon definition. For example:

    cumulus@switch:~$ sudo nano /etc/frr/daemons
    ...
    vtysh_enable=yes
    zebra_options=" -M snmp -A 127.0.0.1 --v6-rr-semantics -s 90000000"
    bgpd_options=" -M snmp  -A 127.0.0.1"
    ospfd_options=" -M snmp -A 127.0.0.1"
    ...
    
  2. Restart FRR with this command:

    cumulus@switch:~$ sudo systemctl restart frr.service

    Restarting FRR restarts all the routing protocol daemons that are enabled and running.

To verify that the IPv6 route replacement option is enabled, run the systemctl status frr command:

cumulus@switch:~$ systemctl status frr

● frr.service - FRRouting
  Loaded: loaded (/lib/systemd/system/frr.service; enabled; vendor preset: enabled)
  Active: active (running) since Mon 2020-02-03 20:02:33 UTC; 3min 8s ago
    Docs: https://frrouting.readthedocs.io/en/latest/setup.html
  Process: 4675 ExecStart=/usr/lib/frr/frrinit.sh start (code=exited, status=0/SUCCESS)
  Memory: 14.4M
  CGroup: /system.slice/frr.service
          ├─4685 /usr/lib/frr/watchfrr -d zebra bgpd staticd
          ├─4701 /usr/lib/frr/zebra -d -M snmp -A 127.0.0.1 --v6-rr-semantics -s 90000000
          ├─4705 /usr/lib/frr/bgpd -d -M snmp -A 127.0.0.1
          └─4711 /usr/lib/frr/staticd -d -A 127.0.0.1