Border Gateway Protocol - BGP
BGP is the routing protocol that runs the Internet. It manages how packets get routed from network to network by exchanging routing and reachability information.
BGP is an increasingly popular protocol for use in the data center as it lends itself well to the rich interconnections in a Clos topology. RFC 7938 provides further details about using BGP in the data center.
How Does BGP Work?
BGP directs packets between autonomous systems (AS), which are a set of routers under a common administration. Each router maintains a routing table that controls how the switch forwards packets. The BGP process on the router generates information in the routing table based on information coming from other routers and from information in the BGP routing information base (RIB). The RIB is a database that stores routes and continually updates the routing table as changes occur.
BGP treats each independently managed enterprise and service provider as an autonomous system, responsible for a set of network addresses. Each such autonomous system has a unique number called an autonomous system number (ASN). A central authority (ICANN) hands out ASNs but numbers between 64512 and 65535 are for private use. When you use BGP within the data center, you must either use this number space or the single ASN you own.
The ASN is central to how BGP builds a forwarding topology. A BGP route advertisement carries with it not only the ASN of the originator, but also the list of ASNs that this route advertisement passes through. When forwarding a route advertisement, a BGP speaker adds itself to this list. The AS path includes the list of ASNs. BGP uses the AS path to detect and avoid loops.
FRRouting supports both 16-bit and 32-bit ASNs.
In a two-tier leaf and spine environment, you can use auto BGP to generate 32-bit ASNs automatically so that you do not have to think about which numbers to configure. Auto BGP helps build optimal ASN configurations in your data center to avoid suboptimal routing and path hunting, which occurs when you assign the wrong spine ASNs. Auto BGP makes no changes to standard BGP behavior or configuration.
Auto BGP assigns private ASNs in the range 4200000000 through 4294967294. This is the private space that RFC 6996 defines. Each leaf has a random and unique value in the range 4200000001 through 4294967294. Each spine has the value 4200000000; the first number in the range. For information about configuring auto BGP, refer to Basic BGP Configuration.
- Use auto BGP in new deployments to avoid conflicting ASNs in an existing configuration.
- It is not necessary to use auto BGP across all switches in your configuration. For example, you can use auto BGP to configure one switch but set ASNs manually to other switches.
- Use auto BGP in two-tier spine and leaf networks. Using auto BGP in three-tier networks with super spines can result in incorrect ASN assignments.
leafkeyword generates the ASN based on a hash of the switch MAC address. The ASN assigned can change after a switch replacement.
- You can configure auto BGP with NCLU or NVUE.
eBGP and iBGP
When you use BGP to peer between autonomous systems, the peering is external BGP or eBGP. When you use BGP within an autonomous system, the peering is internal BGP or iBGP. eBGP peers have different ASNs while iBGP peers have the same ASN.
The heart of the protocol is the same when used as eBGP or iBGP but there is a key difference in the protocol behavior between eBGP and iBGP. To prevent loops, an iBGP speaker does not forward routing information learned from one iBGP peer to another iBGP peer. eBGP prevents loops using the
You need to peer all iBGP speakers with each other in a full mesh. In a large network, this requirement can become unscalable. The most popular method to scale iBGP networks is to introduce a route reflector.
BGP Path Selection
BGP is a path-vector routing algorithm that does not rely on a single routing metric to determine the lowest cost route, unlike interior gateway protocols (IGPs) like OSPF.
The BGP path selection algorithm looks at multiple factors to determine which path is best. Cumulus Linux enables BGP multipath by default so that multiple equal cost routes install in the routing table but only a single route advertises to BGP peers.
The order of the BGP algorithm process is as follows:
Highest Weight: Weight is a value from 0 to 65535. BGP does not carry the weight in an update but uses it locally to influence the best path selection. Locally generated routes have a weight of 32768.
Highest Local Preference: Only iBGP neighbors exchange local preference. BGP assigns routes from eBGP peers a local preference of 0. Whereas weight makes route selections without sending additional information to peers, local preference influences routing to iBGP peers.
Locally Originated Routes: Any route that the local switch places into BGP is the selected best. This includes static routes, aggregate routes and redistributed routes.
Shortest AS Path: BGP selects the path with the fewest number of ASN hops.
Origin Check: Preference to routes with an IGP origin (routes you place into BGP with a
networkstatement) over incomplete origins (routes you place into BGP through redistribution).
Lowest MED: BGP sends the Multi-Exit Discriminator (MED) to eBGP peers to indicate a preference on how traffic enters an AS. BGP exchanges the MED from an eBGP peer with iBGP peers but resets to a value of 0 before advertising a prefix to another AS.
eBGP Routes: The switch uses the route from an eBGP peer over a route learned from an iBGP peer.
Lowest IGP Cost to the Next Hop: The route with the lowest IGP metric to reach the BGP next hop.
Oldest Route: The switch uses the oldest route in the BGP table.
Lowest Router ID: The switch uses the route from the peer with the lowest Router ID attribute. If the route is from a route reflector, the switch uses the
ORIGINATOR_IDattribute for comparison.
Shortest Route Reflector Cluster List: If a route passes through multiple route reflectors, the switch uses the route with the shortest route reflector cluster list.
Highest Peer IP Address: The switch uses the route from the peer with the highest IP address.
Cumulus Linux provides the reason it selects one path over another in NCLU
net show bgp and vtysh
show ip bgp command output for a specific prefix.
When you use BGP multipath, if multiple paths are equal, BGP still selects a single best path to advertise to peers. This path shows as best with the reason, although BGP can install multiple paths into the routing table.
Historically, peers connect over IPv4 and TCP port 179, and after they establish a session, they exchange prefixes. When a BGP peer advertises an IPv4 prefix, it must include an IPv4 next hop address, which is the address of the advertising router. This requires each BGP peer to have an IPv4 address, which in a large network can consume a lot of address space and can require a separate IP address for each peer-facing interface.
The BGP unnumbered standard in RFC 5549, uses extended next hop encoding (ENHE) and does not require that you advertise an IPv4 prefix together with an IPv4 next hop. You can configure BGP peering between your Cumulus Linux switches and exchange IPv4 prefixes without having to configure an IPv4 address on each switch; BGP uses unnumbered interfaces.
The next hop address for each prefix is an IPv6 link-local address, which BGP assigns automatically to each interface. Using the IPv6 link-local address as a next hop instead of an IPv4 unicast address, BGP unnumbered saves you from having to configure IPv4 addresses on each interface.
When you use BGP unnumbered, BGP learns the prefixes, calculates the routes and installs them in IPv4 AFI to IPv6 AFI format. ENHE in Cumulus Linux does not install routes into the kernel in IPv4 prefix to IPv6 next hop format. For link-local peerings that you enable using IPv6 neighbor discovery router advertisements, BGP converts an IPv6 next hop into an IPv4 link-local address. It then installs a static neighbor entry for this IPv4 link-local address with the MAC address that it derives from the link-local address of the other end.
- If you assign an IPv4 /30 or /31 IP address to the interface, BGP uses IPv4 peering instead of IPv6 link-local peering.
- BGP unnumbered only works with two switches at a time (with point-to-point links).
- The IPv6 implementation on the peering device uses the MAC address as the interface ID when assigning the IPv6 link-local address, as suggested by RFC 4291.
- Every router or end host must have an IPv4 address to complete a
tracerouteof IPv4 addresses. In this case, the IPv4 address used is that of the loopback device. Even if extended next hop encoding (ENHE) is not used in the data center, link addresses are not typically advertised because they take up valuable FIB resources and also expose an additional attack vector for intruders to use to either break in or engage in DDOS attacks. Assigning an IP address to the loopback device is essential.
- BGP in the Data Center by Dinesh G. Dutt - a complete guide to Border Gateway Protocol for the modern data center
- Bidirectional forwarding detection (BFD) and BGP
- Wikipedia entry for BGP (includes list of useful RFCs)
- FRR BGP documentation
- IETF draft discussing BGP use within data centers
- RFC 1657, Definitions of Managed Objects for the Fourth Version of the Border Gateway Protocol (BGP-4) using SMIv2
- RFC 1997, BGP Communities Attribute
- RFC 2385, Protection of BGP Sessions via the TCP MD5 Signature Option
- RFC 2439, BGP Route Flap Damping
- RFC 2545, Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing
- RFC 2918, Route Refresh Capability for BGP-4
- RFC 4271, A Border Gateway Protocol 4 (BGP-4)
- RFC 4760, Multiprotocol Extensions for BGP-4
- RFC 5004, Avoid BGP Best Path Transitions from One External to Another
- RFC 5065, Autonomous System Confederations for BGP
- RFC 5291, Outbound Route Filtering Capability for BGP-4
- RFC 5492, Capabilities Advertisement with BGP-4
- RFC 5549, Advertising IPv4 Network Layer Reachability Information with an IPv6 Next Hop
- RFC 6793, BGP Support for Four-Octet Autonomous System (AS) Number Space
- RFC 7911, Advertisement of Multiple Paths in BGP
- draft-walton-bgp-hostname-capability-02, Fully Qualified Domain Name Capability for BGP