In Service System Upgrade - ISSU
Use ISSU to upgrade and troubleshoot an active switch with minimal disruption to the network.
ISSU includes the following modes:
- Restart
- Upgrade
- Maintenance mode
- Maintenance ports
In earlier Cumulus Linux releases, ISSU was Smart System Manager.
Restart Mode
You can restart the switch in one of the following modes.
cold restarts the system and resets all the hardware devices on the switch (including the switching ASIC).
fast restarts the system more efficiently with minimal impact to traffic by reloading the kernel and software stack without a hard reset of the hardware. During a fast restart, the system decouples from the network to the extent possible using existing protocol extensions before recovering to the operational mode of the system. The restart process maintains the forwarding entries of the switching ASIC and the data plane is not affected. Traffic outage is much lower in this mode as there is only a momentary interruption after reboot, while the system reinitializes.
warm restarts the system with no interruption to traffic for existing route entries. Warm mode diverts traffic from itself and restarts the system without a hardware reset of the switch ASIC. While this process does not affect the data plane, the control plane is absent during restart and is unable to process routing updates. However, if no alternate paths exist, the switch continues forwarding with the existing entries with no interruptions.
When you restart the switch in warm mode, BGP performs a graceful restart if the BGP Graceful Restart option is on. To enable BGP Graceful Restart, refer to Optional BGP Configuration.
Cumulus Linux supports fast mode for all protocols; however only supports warm mode for layer 2 forwarding, and layer 3 forwarding with BGP and static routing.
The following command restarts the system in cold mode:
cumulus@switch:~$ sudo csmgrctl -c
The following command restarts the system in fast mode:
cumulus@switch:~$ sudo csmgrctl -f
The following command restarts the system in warm mode.
Warm boot resets any manually configured FEC settings.
cumulus@switch:~$ sudo csmgrctl -w
Upgrade Mode
Upgrade mode updates all the components and services on the switch to the latest Cumulus Linux minor release without impacting traffic. After upgrade is complete, you must restart the switch with either a cold or fast restart.
Upgrade mode includes the following options:
- all runs
apt-get upgrade
to upgrade all the system components to the latest minor release without affecting traffic flow. You must restart the system after the upgrade completes with one of the restart modes. - dry-run provides information on the components you want to upgrade.
The following command upgrades all the system components:
cumulus@switch:~$ sudo csmgrctl -u
The following command provides information on the components you want to upgrade:
cumulus@switch:~$ sudo csmgrctl -d
Maintenance Mode
Maintenance mode globally manages the BGP and MLAG control plane.
- When you enable maintenance mode, BGP and MLAG shut down gracefully.
- When you disable maintenance mode, BGP and MLAG are enabled based on the individual parameter settings.
To enable maintenance mode:
cumulus@switch:~$ nv action enable system maintenance mode
Action executing ...
System maintenance mode has been enabled successfully
Current System Mode: Maintenance, cold
Maintenance mode since Thu Jun 13 23:59:47 2024 (Duration: 00:00:00)
Ports shutdown for Maintenance
frr : Maintenance, cold, down, up time: 29:06:27
switchd : Maintenance, cold, down, up time: 29:06:31
System Services : Maintenance, cold, down, up time: 29:07:00
Action succeeded
cumulus@switch:~$ sudo csmgrctl -m1
To disable maintenance mode:
cumulus@switch:~$ nv action disable system maintenance mode
Action executing ...
System maintenance mode has been disabled successfully
Current System Mode: cold
frr : cold, up, up time: 12:57:48 (1 restart)
switchd : cold, up, up time: 13:12:13
System Services : cold, up, up time: 13:12:32
Action succeeded
cumulus@switch:~$ sudo csmgrctl -m0
Before you disable maintenance mode, be sure to bring the ports back up.
To show maintenance mode status either run the NVUE nv show system maintenance
command or the Linux sudo csmgrctl -s
command:
cumulus@switch:~$ nv show system maintenance
operational
----- -----------
mode enabled
ports disabled
cumulus@switch:~$ sudo csmgrctl -s
Current System Mode: cold
frr : cold, up, up time: 00:14:51 (2 restarts)
clagd : cold, up, up time: 00:14:47
switchd : cold, up, up time: 01:09:48
System Services : cold, up, up time: 01:10:07
Maintenance Ports
Maintenance ports globally disables or enables all configured ports.
- When you enable maintenance ports, swp interfaces follow individual admin states.
- When you disable maintenance ports, swp interfaces are globally admin down, overriding the admin state in the configuration.
To enable maintenance ports:
cumulus@switch:~$ nv action enable system maintenance ports
Action executing ...
System maintenance ports has been enabled successfully
Current System Mode: cold
frr : cold, up, up time: 28:54:36
switchd : cold, up, up time: 28:54:40
System Services : cold, up, up time: 28:55:09
Action succeeded
cumulus@switch:~$ sudo csmgrctl -p0
To disable maintenance ports:
cumulus@switch:~$ nv action disable system maintenance ports
Action executing ...
System maintenance ports has been disabled successfully
Current System Mode: cold
Ports shutdown for Maintenance
frr : cold, up, up time: 28:55:49
switchd : cold, up, up time: 28:55:53
System Services : cold, up, up time: 28:56:22
Action succeeded
cumulus@switch:~$ sudo csmgrctl -p1
To see the status of maintenance ports, run the NVUE nv show system maintenance
command:
cumulus@switch:~$ nv show system maintenance
operational
----- -----------
mode enabled
ports disabled