SPAN and ERSPAN
Cumulus Linux supports both SPAN and ERSPAN.
SPAN mirrors all packets that come in from or go out of an interface (the SPAN source), and copy and transmit the packets out of a local port or CPU (the SPAN destination) for monitoring. The SPAN destination port is also referred to as a mirror-to-port (MTP). The original packet is still switched, while a mirrored copy of the packet goes out of the MTP.
ERSPAN sends the mirrored packets to a monitoring node located anywhere across the routed network. The switch finds the outgoing port of the mirrored packets by looking up the destination IP address in its routing table. The switch encapsulates the original layer 2 packet with GRE for IP delivery. The encapsulated packets have the following format:
---------------------------------------------------------- | MAC_HEADER | IP_HEADER | GRE_HEADER | L2_Mirrored_Packet | ----------------------------------------------------------
SPAN
To configure SPAN to mirror ports on your switch, you create a port mirror session. The session ID is a number between 0 and 7.
You set the following SPAN options:
- Source port
- Destination port
- Direction (ingress or egress)
Run the nv set system port-mirror session <session-id> span <option>
command. The NVUE commands save the configuration in the /etc/cumulus/switchd.d/port-mirror.conf
file.
To reduce the volume of data, you can truncate the mirrored frames at a specified number of bytes. The size must be between 4 and 4088 bytes and a multiple of 4.
Example Commands
To mirror all packets received on swp1, and copy and transmit the packets to swp2 for monitoring:
cumulus@switch:~$ nv set system port-mirror session 1 span direction ingress
cumulus@switch:~$ nv set system port-mirror session 1 span source-port swp1
cumulus@switch:~$ nv set system port-mirror session 1 span destination swp2
cumulus@switch:~$ nv config apply
To mirror all packets that go out of swp1, and copy and transmit the packets to swp2 for monitoring:
cumulus@switch:~$ nv set system port-mirror session 1 span direction egress
cumulus@switch:~$ nv set system port-mirror session 1 span source-port swp1
cumulus@switch:~$ nv set system port-mirror session 1 span destination swp2
cumulus@switch:~$ nv config apply
SPAN sessions that reference an outgoing interface create the mirrored packets according to the ingress interface before the routing decision. For example, the above commands capture traffic that is ultimately destined to leave swp1 but mirrors the packets when they arrive on swp2. Packets that reference the original VLAN tag, and the source and destination MAC address transfer when swp2 originally receives the packet.
To mirror packets from all ports to swp53:
cumulus@switch:~$ nv set system port-mirror session 1 span direction ingress
cumulus@switch:~$ nv set system port-mirror session 1 span source-port swp1-54
cumulus@switch:~$ nv set system port-mirror session 1 span destination swp53
cumulus@switch:~$ nv config apply
To mirror all packets received on bond1, and copy and transmit the packets to swp53 for monitoring:
cumulus@switch:~$ nv set system port-mirror session 1 span direction ingress
cumulus@switch:~$ nv set system port-mirror session 1 span source-port bond1
cumulus@switch:~$ nv set system port-mirror session 1 span destination swp53
cumulus@switch:~$ nv config apply
To truncate the mirrored frames at 40 bytes:
cumulus@switch:~$ nv set system port-mirror session 1 span truncate size 40
cumulus@switch:~$ nv config apply
Delete SPAN Sessions
You can delete all SPAN sessions with the nv unset system port-mirror
command. For example:
cumulus@switch:~$ nv unset system port-mirror
cumulus@switch:~$ nv config apply
To delete a specific SPAN session, run the nv unset system port-mirror session <session-id>
command. For example:
cumulus@switch:~$ nv unset system port-mirror session 1
cumulus@switch:~$ nv config apply
Edit the /etc/cumulus/switchd.d/port-mirror.conf
file, then load the configuration.
The following example configuration mirrors all packets received on swp1, and copies and transmits the packets to swp2 for monitoring:
cumulus@switch:~$ sudo nano /etc/cumulus/switchd.d/port-mirror.conf
Copyright © 2021 NVIDIA CORPORATION & AFFILIATES. ALL RIGHTS RESERVED.
#
# This software product is a proprietary product of Nvidia Corporation and its affiliates
# (the "Company") and all right, title, and interest in and to the software
# product, including all associated intellectual property rights, are and
# shall remain exclusively with the Company.
#
# This software product is governed by the End User License Agreement
# provided with the software product.
#
# [session_n]
# session-id = n
# mirror.session.n.direction = (ingress | egress)
# mirror.session.n.src = <swpx, bond>
# mirror.session.n.dest = (swpx | <src-ip> <dst-ip>)
# mirror.session.n.type = (span | erspan | none)
#
# Default is all sessions off
# mirror.session.all.type = none
[session_1]
session-id = 1
mirror.session.1.direction = ingress
mirror.session.1.src = swp1
mirror.session.1.dest = swp2
mirror.session.1.type = span
Run the following command to the load the configuration:
cumulus@switch:~$ /usr/lib/cumulus/switchdctl --load /etc/cumulus/switchd.d/port-mirror.conf -prefix mirror
SPAN sessions that reference an outgoing interface create the mirrored packets according to the ingress interface before the routing decision. For example, the following rule captures traffic that is ultimately destined to leave swp1 but mirrors the packets when they arrive on swp49. The rule transmits packets that reference the original VLAN tag, and source and destination MAC address at the time that swp49 originally receives the packet.
[session_1]
session-id = 1
mirror.session.1.direction = egress
mirror.session.1.src = swp1
mirror.session.1.dest = swp49
mirror.session.1.type = span
cumulus@switch:~$ /usr/lib/cumulus/switchdctl --load /etc/cumulus/switchd.d/port-mirror.conf -prefix mirror
Selective SPAN with ACLs
You can configure selective SPAN with ACLs to mirror a subset of traffic according to:
- Source or destination IP address
- IP protocol
- TCP or UDP source or destination port
- TCP flags
- An ingress port
To match swp1 ingress traffic that has the source IP address 10.10.1.1 and mirror the traffic to swp2 when a match occurs:
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 type ipv4
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 match ip source-ip 10.10.1.1
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action span swp2
cumulus@switch:~$ nv set interface swp1 acl EXAMPLE1 inbound
To match OSPF packets coming in on swp1 and mirror the traffic to swp2 when a match occurs:
cumulus@switch:~$ nv set acl EXAMPLE1 type ipv4
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 match ip protocol ospf
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action span swp2
cumulus@switch:~$ nv set interface swp1 acl EXAMPLE1 inbound
To match UDP packets coming in on bond1 and mirror the traffic to swp53 when a match occurs:
cumulus@switch:~$ nv set acl EXAMPLE1 type ipv4
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 match ip protocol udp
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action span swp53
cumulus@switch:~$ nv set interface bond1 acl EXAMPLE1 inbound
cumulus@switch:~$ nv config apply
- Always place your rule files in the
/etc/cumulus/acl/policy.d/
directory. - Using
cl-acltool
with the--out-interface
rule applies to transit traffic only; it does not apply to traffic sourced from the switch. --out-interface
rules cannot target bond interfaces, only the bond members tied to them. For example, to mirror all packets going out of bond1 to swp53, where bond1 members are swp1 and swp2, create the rule-A FORWARD --out-interface swp1,swp2 -j SPAN --dport swp53
.
Create a rules file in the
/etc/cumulus/acl/policy.d/
directory. The following example rules mirror ICMP packets that ingress swp1 to swp54 and UDP packets that egress swp4 to swp53:cumulus@switch:~$ sudo nano /etc/cumulus/acl/policy.d/span.rules [iptables] -A FORWARD --in-interface swp1 -p icmp -j SPAN --dport swp54 -A FORWARD --out-interface swp4 -p udp -j SPAN --dport swp53
Install the rules:
cumulus@switch:~$ sudo cl-acltool -i
Do not run the cl-acltool -i
command with -P
option. The -P
option removes all existing control plane rules or other installed rules and only installs the rules defined in the specified file.
Verify that you installed the SPAN rules:
cumulus@switch:~$ sudo cl-acltool -L all | grep SPAN 38025 7034K SPAN icmp -- swp1 any anywhere anywhere dport:swp54 50832 55M SPAN udp -- any swp4 anywhere anywhere dport:swp53
Example Rules
To mirror forwarded packets from all ports matching source IP address 20.0.1.0 and destination IP address 20.0.1.2 to port swp1:
-A FORWARD --in-interface swp+ -s 20.0.0.2 -d 20.0.1.2 -j SPAN --dport swp1
To mirror ICMP packets from all ports to swp1:
-A FORWARD --in-interface swp+ -s 20.0.0.2 -p icmp -j SPAN --dport swp1
To mirror forwarded UDP packets received from port swp1, towards destination IP address 20.0.1.2 and destination port 53:
-A FORWARD --in-interface swp1 -d 20.0.1.2 -p udp --dport 53 -j SPAN --dport swp1
To mirror all forwarded TCP packets with only SYN set:
-A FORWARD --in-interface swp+ -p tcp --tcp-flags ALL SYN -j SPAN --dport swp1
To mirror all forwarded TCP packets with only FIN set:
-A FORWARD --in-interface swp+ -p tcp --tcp-flags ALL FIN -j SPAN --dport swp1
CPU port as the SPAN Destination
You can set the CPU port as a SPAN destination interface to mirror data plane traffic to the CPU. The SPAN traffic goes to a separate network interface mirror where you can analyze it with tcpdump
. This is a useful feature if you do not have any free external ports on the switch for monitoring. SPAN traffic does not appear on switch ports.
Cumulus Linux controls how much traffic reaches the CPU so that mirrored traffic does not overwhelm the CPU.
You configure the CPU port as the SPAN destination with ACLs.
To monitor traffic mirrored to the CPU, run the tcpcdump -i mirror
command.
- Cumulus Linux does not support egress mirroring for control plane generated traffic to the CPU port.
- When you set the CPU port as a SPAN destination interface, Cumulus Linux mirrors packets that match the rule on both ingress and egress only one time to the destination interface.
To match swp1 ingress traffic that has the source IP address 10.10.1.1 and mirror the traffic to the CPU when a match occurs:
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action span cpu
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 match ip source-ip 10.10.1.1
cumulus@switch:~$ nv set acl EXAMPLE1 type ipv4
cumulus@switch:~$ nv set interface swp1 acl EXAMPLE1 inbound
cumulus@switch:~$ nv config apply
To match swp1 egress traffic that has the source IP address 10.10.1.1 and mirror the traffic to the CPU when a match occurs:
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action span cpu
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 match ip source-ip 10.10.1.1
cumulus@switch:~$ nv set acl EXAMPLE1 type ipv4
cumulus@switch:~$ nv set interface swp1 acl EXAMPLE1 outbound
cumulus@switch:~$ nv config apply
Create a file in the
/etc/cumulus/acl/policy.d/
directory and add rules.To match swp1 ingress traffic that has the source IP address 10.10.1.1 and mirror the traffic to the CPU when a match occurs:
cumulus@switch:~$ sudo nano /etc/cumulus/acl/policy.d/span-cpu.rules [iptables] -A FORWARD -i swp1 -s 10.10.1.1 -j SPAN --dport cpu
To match swp1 egress traffic that has the source IP address 10.10.1.1 and mirror the traffic to the CPU when a match occurs:
-A FORWARD -o swp1 -s 10.10.1.1 -j SPAN --dport cpu
Install the rule:
cumulus@switch:~$ sudo cl-acltool -i
Do not run the cl-acltool -i
command with -P
option. The -P
option removes all existing control plane rules or other installed rules and only installs the rules defined in the specified file.
ERSPAN
To configure ERSPAN to mirror ports on your switch, you create a port mirror session. The session ID is a number between 0 and 7.
You can set the following ERSPAN options:
- Source port
- Direction (ingress or egress)
- Source IP address for ERSPAN encapsulation
- Destination IP address for ERSPAN encapsulation
Run the nv set system port-mirror session <session-id> erspan <option>
command. The NVUE commands save the configuration in the /etc/cumulus/switchd.d/port-mirror.conf
file.
To reduce the volume of data, you can truncate the mirrored frames at a specified number of bytes. The size must be between 4 and 4088 bytes and a multiple of 4.
Example Commands
The following examples configure ERSPAN encapsulation from source IP address 10.10.10.1 to destination IP address 10.10.10.234.
To mirror all packets that arrive on swp1:
cumulus@switch:~$ nv set system port-mirror session 1 erspan direction ingress
cumulus@switch:~$ nv set system port-mirror session 1 erspan source-port swp1
cumulus@switch:~$ nv set system port-mirror session 1 erspan destination source-ip 10.10.10.1
cumulus@switch:~$ nv set system port-mirror session 1 erspan destination dest-ip 10.10.10.234
cumulus@switch:~$ nv config apply
To mirror all packets that go out of swp1:
cumulus@switch:~$ nv set system port-mirror session 1 erspan direction egress
cumulus@switch:~$ nv set system port-mirror session 1 erspan source-port swp1
cumulus@switch:~$ nv set system port-mirror session 1 erspan destination source-ip 10.10.10.1
cumulus@switch:~$ nv set system port-mirror session 1 erspan destination dest-ip 10.10.10.234
cumulus@switch:~$ nv config apply
Delete ERSPAN Sessions
You can delete all ERSPAN sessions with the nv unset system port-mirror
command. For example:
cumulus@switch:~$ nv unset system port-mirror
cumulus@switch:~$ nv config apply
To delete a specific ERSPAN session, run the nv unset system port-mirror session <session-id>
command. For example:
cumulus@switch:~$ nv unset system port-mirror session 1
cumulus@switch:~$ nv config apply
Edit the /etc/cumulus/switchd.d/port-mirror.conf
file, then load the configuration.
The following example ERSPAN configuration mirrors all packets received on swp1:
cumulus@switch:~$ sudo nano /etc/cumulus/switchd.d/port-mirror.conf
Copyright © 2021 NVIDIA CORPORATION & AFFILIATES. ALL RIGHTS RESERVED.
#
# This software product is a proprietary product of Nvidia Corporation and its affiliates
# (the "Company") and all right, title, and interest in and to the software
# product, including all associated intellectual property rights, are and
# shall remain exclusively with the Company.
#
# This software product is governed by the End User License Agreement
# provided with the software product.
#
# [session_n]
# session-id = n
# mirror.session.n.direction = (ingress | egress)
# mirror.session.n.src = <swpx, bond>
# mirror.session.n.dest = (swpx | <src-ip> <dst-ip>)
# mirror.session.n.type = (span | erspan | none)
#
# Default is all sessions off
# mirror.session.all.type = none
[session_1]
session-id = 1
mirror.session.1.direction = ingress
mirror.session.1.src = swp1
mirror.session.1.dest = 10.10.10.1 10.10.10.234
mirror.session.1.type = erspan
Run the following command to the load the configuration:
cumulus@switch:~$ /usr/lib/cumulus/switchdctl --load /etc/cumulus/switchd.d/port-mirror.conf -prefix mirror
- If you use Wireshark to review the ERSPAN output, you might see the Wireshark error message
Unknown version, please report or test to use fake ERSPAN preference
and the trace might be unreadable. To resolve this issue, go to Protocols \ ERSPAN from the Wireshark General preferences and check the Force to decode fake ERSPAN frame option. - To set up a capture filter on the destination switch that filters for a specific IP protocol, use
ip.proto == 47
to filter for GRE-encapsulated (IP protocol 47) traffic.
Selective ERSPAN with ACLs
You can configure selective ERSPAN with ACLs to mirror a subset of traffic according to:
- Source or destination IP address
- IP protocol
- TCP or UDP source or destination port
- TCP flags
- An ingress port
The following command mirrors inbound ICMP packets from all swp interfaces. The source IP address for ERSPAN encapsulation is 10.10.10.1 and the destination IP address for ERSPAN encapsulation is 10.10.10.234.
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 type ipv4
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 match ip protocol icmp
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action erspan source-ip 10.10.10.1
cumulus@switch:~$ nv set acl EXAMPLE1 rule 1 action erspan dest-ip 10.10.10.234
cumulus@switch:~$ nv set interface swp1-54 acl EXAMPLE1 inbound
cumulus@switch:~$ nv config apply
Create a rules file in
/etc/cumulus/acl/policy.d/
. The following rule configures ERSPAN for all ICMP packets that ingress swp1. The source IP address for ERSPAN encapsulation is 10.10.10.1 and the destination IP address for ERSPAN encapsulation is 10.10.10.234.cumulus@switch:~$ sudo nano /etc/cumulus/acl/policy.d/erspan.rules [iptables] -A FORWARD --in-interface swp1 -p icmp -j ERSPAN --src-ip 10.10.10.1 --dst-ip 10.10.10.234
src-ip
can be any IP address, even if it does not exist in the routing table.dst-ip
must be an IP address reachable through the routing table and front-panel port (not the management port) or SVI. Use ping or ip route getto verify that the destination IP address is reachable. Install the rules:
cumulus@switch:~$ sudo cl-acltool -i
Do not run the cl-acltool -i
command with -P
option. The -P
option removes all existing control plane rules or other installed rules and only installs the rules defined in the specified file.
Verify that you installed the ERSPAN rules:
cumulus@switch:~$ sudo iptables -L -v | grep ERSPAN 29 0 ERSPAN icmp -- swp1 any anywhere anywhere ERSPAN src-ip:10.10.10.1 dst-ip:10.10.10.234
Example Rules
In the following example rules, the source IP address for ERSPAN encapsulation is 10.10.10.1 and the destination IP address for ERSPAN encapsulation is 10.10.10.234.
To mirror forwarded packets from all ports matching the source IP address 20.0.0.2 and the destination IP address 20.0.1.2:
-A FORWARD --in-interface swp+ -s 20.0.0.2 -d 20.0.1.2 -j ERSPAN --src-ip 10.10.10.1 --dst-ip 10.10.10.234
To mirror ICMP packets from all ports:
-A FORWARD --in-interface swp+ -p icmp -j ERSPAN --src-ip 10.10.10.1 --dst-ip 10.10.10.234
To mirror forwarded UDP packets with destination port 53 arriving on swp1:
-A FORWARD --in-interface swp1 -p udp --dport 53 -j ERSPAN --src-ip 10.10.10.1 --dest-ip 10.10.10.234
To mirror all forwarded TCP packets with only SYN set:
-A FORWARD --in-interface swp+ -p tcp --tcp-flags ALL SYN -j ERSPAN --src-ip 10.10.10.1 --dst-ip 10.10.10.234
To mirror all forwarded TCP packets with only FIN set:
-A FORWARD --in-interface swp+ -p tcp --tcp-flags ALL FIN -j ERSPAN --src-ip 10.10.10.1 --dst-ip 10.10.10.234
Show SPAN and ERSPAN Configuration
To show SPAN and ERSPAN configuration for a specific session, run the NVUE nv show system port-mirror session <session-id>
command. To show SPAN and ERSPAN configuration for all sessions, run the NVUE nv show system port-mirror
command.
cumulus@switch:~$ nv show system port-mirror session 1
operational applied pending
--------------- ----------- ------- -------
erspan
enable off
span
enable on
direction ingress
[destination]
[source-port] swp1
truncate
enable off
You can also run the sudo cl-acltool -L all | grep SPAN
or sudo cl-acltool -L all | grep ERSPAN
command.
cumulus@switch:~$ sudo cl-acltool -L all | grep SPAN
0 0 SPAN all -- any swp1 10.10.10.1 anywhere /* rule_id:1,acl_name:EXAMPLE1,dir:outbound,interface_id:swp1 */ dport:cpu
Limitations
- On a switch with the Spectrum-2 ASIC or later, Cumulus Linux supports four SPAN destinations in atomic mode or eight SPAN destinations in non-atomic mode. On a switch with the Spectrum 1 ASIC, Cumulus Linux supports only a single SPAN destination in atomic mode or three SPAN destinations in non-atomic mode.
- WJH buffer drop monitoring uses a SPAN destination; if you configure What Just Happened (WJH), ensure that you do not exceed the total number of SPAN destinations allowed for your switch ASIC type.
- Multiple SPAN sources can point to the same SPAN destination, but a SPAN source cannot specify two SPAN destinations.
- Cumulus Linux does not support IPv6 ERSPAN destinations.
- You cannot use eth0 as a destination.
- You cannot mirror packets that egress a bond interface (such as bond1); you can only mirror packets that egress bond members (such as swp1, swp2 and so on).
- Mirrored traffic is not guaranteed. A congested MTP results in discarded mirrored packets.
- A oversubscribed SPAN and ERSPAN destination interface might result in data plane buffer depletion and buffer drops. Exercise caution when enabling SPAN and ERSPAN when the aggregate speed of all source ports exceeds the destination port.
- ERSPAN does not cause the kernel to send ARP requests to resolve the next hop for the ERSPAN destination. If an ARP entry for the destination or next hop does not already exist in the kernel, you need to manually resolve this before sending mirrored traffic (use
ping
orarping
). - Mirroring to the same interface that you are monitoring causes a recursive flood of traffic and might impact traffic on other interfaces.
- Cumulus VX does not support ACL-based SPAN, ERSPAN, or port mirroring. To capture packets in Cumulus VX, use the
tcpdump
command line network traffic analyzer. - When you configure ERSPAN sessions with the NVUE
nv set system port-mirror
commands, the destination IP address must be reachable from the source IP address through the default VRF.