VLAN-aware Bridge Mode
VLAN-aware bridge mode in Cumulus Linux implements a configuration model for large-scale layer 2 environments, with one single instance of spanning tree protocol. Each physical bridge member port includes the list of allowed VLANs as well as the port VLAN ID, either the primary VLAN Identifier (PVID) or native VLAN. MAC address learning, filtering and forwarding are VLAN-aware. This reduces the configuration size, and eliminates the large overhead of managing the port and VLAN instances as subinterfaces, replacing them with lightweight VLAN bitmaps and state updates.
Cumulus Linux supports multiple VLAN-aware bridges but with the following limitations:
- You cannot use MLAG with multiple VLAN-aware bridges.
- You cannot use the same port with multiple VLAN-aware bridges.
- You cannot use the same VNIs in multiple VLAN-aware bridges.
- You cannot use VLAN translation with multiple VLAN-aware bridges.
- You cannot use double tagged VLAN interfaces with multiple VLAN-aware bridges.
- You cannot associate multiple single VXLAN devices (SVDs) with a single VLAN-aware bridge
Configure a VLAN-aware Bridge
The example commands below create a VLAN-aware bridge for STP that contains two switch ports and includes 3 VLANs; tagged VLANs 10 and 20, and untagged (native) VLAN 1.
With NVUE, there is a default bridge called br_default
, which has no ports assigned. The example below configures this default bridge.
cumulus@switch:~$ nv set interface swp1-2 bridge domain br_default
cumulus@switch:~$ nv set bridge domain br_default vlan 10,20
cumulus@switch:~$ nv set bridge domain br_default untagged 1
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file and add the bridge:
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
bridge-ports swp1 swp2
bridge-vids 10 20
bridge-pvid 1
bridge-vlan-aware yes
...
Run the ifreload -a
command to load the new configuration:
cumulus@switch:~$ ifreload -a
The Primary VLAN Identifier (PVID) of the bridge defaults to 1. You do not have to specify bridge-pvid
for a bridge or a port. However, even though this does not affect the configuration, it helps other users for readability. The following configurations are identical to each other and the configuration above:
auto br_default
iface br_default
bridge-ports swp1 swp2
bridge-vids 1 10 20
bridge-vlan-aware yes
auto br_default
iface br_default
bridge-ports swp1 swp2
bridge-pvid 1
bridge-vids 1 10 20
bridge-vlan-aware yes
auto br_default
iface br_default
bridge-ports swp1 swp2
bridge-vids 10 20
bridge-vlan-aware yes
- If you specify
bridge-vids
orbridge-pvid
at the bridge level, all ports in the bridge inherit these configurations. However, specifying any of these settings for a specific port overrides the setting in the bridge. - Do not bridge the management port eth0 with any switch ports. For example, if you create a bridge with eth0 and swp1, the bridge does not work correctly and disrupts access to the management interface.
Configure Multiple VLAN-aware Bridges
This example shows the commands required to create two VLAN-aware bridges on the switch.
- bridge1 bridges swp1 and swp2, and includes 2 VLANs;
vlan 10
andvlan 20
- bridge2 bridges swp3 and contains one VLAN;
vlan 10
Bridges are independent so you can reuse VLANs between bridges. Each VLAN-aware bridge maintains its own MAC address and VLAN tag table; MAC and VLAN tags in one bridge are not visible to the other table.
cumulus@switch:~$ nv set interface swp1-2 bridge domain bridge1
cumulus@switch:~$ nv set bridge domain bridge1 vlan 10,20
cumulus@switch:~$ nv set bridge domain bridge1 untagged 1
cumulus@switch:~$ nv set interface swp3 bridge domain bridge2
cumulus@switch:~$ nv set bridge domain bridge2 vlan 10
cumulus@switch:~$ nv set bridge domain bridge2 untagged 1
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file and add the bridge:
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bridge1
iface bridge1
bridge-ports swp1 swp2
bridge-vlan-aware yes
bridge-vids 10 20
bridge-pvid 1
auto bridge2
iface bridge2
bridge-ports swp3
bridge-vlan-aware yes
bridge-vids 10
bridge-pvid 1
...
Run the ifreload -a
command to load the new configuration:
cumulus@switch:~$ ifreload -a
NVIDIA Spectrum 1 switches support a maximum of 10000 VLAN elements. NVIDIA Spectrum-2 switches and later support a maximum of 15996 VLAN elements when warm restart mode is off
or 7934 VLAN elements when warm restart mode is on
.
Cumulus Linux calculates the total number of VLAN elements as the number of VLANs times the number of configured bridges. For example, 6 bridges, each containing 2600 VLANs totals 15600 VLAN elements.
On NVIDIA Spectrum-2 switches and later, if you enable multiple VLAN-aware bridges and want to use more VLAN elements than the default, you must update the number of VLAN elements in the /etc/mlx/datapath/broadcast_domains.conf
file.
- To specify the total number of bridge domains you want to use, uncomment and edit the
broadcast_domain.max_vlans
parameter. The default value is 6143 when warm restart mode isoff
or 4096 when warm restart mode ison
. - To specify the total number of subinterfaces you want to use, uncomment and edit the
broadcast_domain.max_subinterfaces
parameter. The default value is 3872 when warm restart mode isoff
or 1872 when warm restart mode ison
.
You must restart switchd
with the systemctl restart switchd
command to apply the configuration.
The number of broadcast_domain.max_vlans
plus broadcast_domain.max_subinterfaces
cannot exceed 15996.
Increasing the broadcast_domain.max_vlans
parameter can affect layer 2 multicast scale support.
Reserved VLAN Range
For hardware data plane internal operations, the switching silicon requires VLANs for every physical port, Linux bridge, and layer 3 subinterface. Cumulus Linux reserves a range of VLANs by default; the reserved range is 3725-3999.
If the reserved VLAN range conflicts with any user-defined VLANs, you can modify the range. The new range must be a contiguous set of VLANs with IDs between 2 and 4094. For a single VLAN-aware bridge, the minimum size of the range is 2 VLANs. For multiple VLAN-aware bridges, the minimum size of the range is the number of VLAN-aware bridges on the system plus one.
The following example changes the reserved VLAN range to be between 4064 and 4094:
cumulus@switch:~$ nv set system global reserved vlan internal range 4064-4094
cumulus@switch:~$ nv config apply
Edit the
/etc/cumulus/switchd.conf
file to uncomment theresv_vlan_range
line and specify a new range.cumulus@switch:~$ sudo nano /etc/cumulus/switchd.conf ... # global reserved vlan internal range resv_vlan_range = 4064-4094
After you save the file, you must restart
switchd
:cumulus@switch:~$ sudo systemctl restart switchd.service
VLAN Pruning
By default, the bridge port inherits the bridge VIDs, however, you can configure a port to override the bridge VIDs.
This example commands configure swp3 to override the bridge VIDs:
cumulus@switch:~$ nv set interface swp1-3 bridge domain br_default
cumulus@switch:~$ nv set bridge domain br_default vlan 10,20
cumulus@switch:~$ nv set bridge domain br_default untagged 1
cumulus@switch:~$ nv set interface swp3 bridge domain br_default vlan 20
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file, then run the ifreload -a
command. The following example commands configure swp3 to override the bridge VIDs:
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
bridge-ports swp1 swp2 swp3
bridge-pvid 1
bridge-vids 10 20
bridge-vlan-aware yes
auto swp3
iface swp3
bridge-vids 20
...
cumulus@switch:~$ ifreload -a
Access Ports and Tagged Packets
Access ports ignore all tagged packets. In the configuration below, swp1 and swp2 are access ports, while all untagged traffic goes to VLAN 10:
cumulus@switch:~$ nv set interface swp1-2 bridge domain br_default
cumulus@switch:~$ nv set bridge domain br_default vlan 10,20
cumulus@switch:~$ nv set bridge domain br_default untagged 1
cumulus@switch:~$ nv set interface swp1 bridge domain br_default access 10
cumulus@switch:~$ nv set interface swp2 bridge domain br_default access 10
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file, then run the ifreload -a
command.
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
bridge-ports swp1 swp2
bridge-pvid 1
bridge-vids 10 20
bridge-vlan-aware yes
auto swp1
iface swp1
bridge-access 10
auto swp2
iface swp2
bridge-access 10
...
cumulus@switch:~$ ifreload -a
Drop Untagged Frames
With VLAN-aware bridge mode, you can configure a switch port to drop any untagged frames. To do this, add bridge-allow-untagged no
to the switch port (not to the bridge). The bridge port is without a PVID and drops untagged packets.
The following example command configures swp2 to drop untagged frames:
cumulus@switch:~$ nv set interface swp2 bridge domain br_default untagged none
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file to add the bridge-allow-untagged no
line under the switch port interface stanza, then run the ifreload -a
command.
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto swp1
iface swp1
auto swp2
iface swp2
bridge-allow-untagged no
auto br_default
iface br_default
bridge-ports swp1 swp2
bridge-pvid 1
bridge-vids 10 20
bridge-vlan-aware yes
...
cumulus@switch:~$ sudo ifreload -a
When you check VLAN membership for that port, it shows that there is no untagged VLAN.
cumulus@switch:~$ bridge -c vlan show
portvlan ids
swp1 1 PVID Egress Untagged
10 20
swp2 10 20
bridge 1
VLAN Layer 3 Addressing
When configuring the VLAN attributes for the bridge, specify the attributes for each VLAN interface. If you are configuring the switch virtual interface (SVI) for the native VLAN, you must declare the native VLAN and specify its IP address. Specifying the IP address in the bridge stanza itself returns an error.
The following example commands declare native VLAN 10 with IPv4 address 10.1.10.2/24 and IPv6 address 2001:db8::1/32.
The NVUE and Linux commands also show an example with multiple VLAN-aware bridges.
cumulus@switch:~$ nv set interface vlan10 ip address 10.1.10.2/24
cumulus@switch:~$ nv set interface vlan10 ip address 2001:db8::1/32
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set interface bridge2_vlan10 type svi
cumulus@switch:~$ nv set interface bridge2_vlan10 vlan 10
cumulus@switch:~$ nv set interface bridge2_vlan10 base-interface bridge2
cumulus@switch:~$ nv set interface bridge2_vlan10 ip address 10.1.10.2/24
cumulus@switch:~$ nv set interface bridge1_vlan10 type svi
cumulus@switch:~$ nv set interface bridge1_vlan10 vlan 10
cumulus@switch:~$ nv set interface bridge1_vlan10 base-interface bridge1
cumulus@switch:~$ nv set interface bridge1_vlan10 ip address 12.1.10.2/24
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file, then run the ifreload -a
command.
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bridge
iface bridge
bridge-ports swp1 swp2
bridge-pvid 1
bridge-vids 10 20
bridge-vlan-aware yes
auto vlan10
iface vlan10
address 10.1.10.2/24
address 2001:db8::1/32
vlan-id 10
vlan-raw-device br_default
cumulus@switch:~$ ifreload -a
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bridge2_vlan10
iface bridge2_vlan10
address 10.1.10.2/24
hwaddress 1c:34:da:1d:e6:fd
vlan-raw-device bridge2
vlan-id 10
auto bridge1_vlan10
iface bridge1_vlan10
address 12.1.10.2/24
hwaddress 1c:34:da:1d:e6:fd
vlan-raw-device bridge1
vlan-id 10
Keep SVIs Perpetually UP
The first time you configure a switch, all southbound bridge ports are down; therefore, by default, SVIs are also down. You can force SVIs to always be up by disabling interface state tracking so that the SVIs are always in the UP state even when all member ports are down. Other implementations describe this feature as no autostate. This is beneficial if you want to perform connectivity testing.
To configure all SVIs on the switch to be perpetually UP, run the nv set system global svi-force-up enable on
command.
cumulus@switch:~$ nv set system global svi-force-up enable on
cumulus@switch:~$ nv config apply
To configure SVIs in a specific bridge to be perpetually UP, run the nv set bridge domain <bridge> svi-force-up enable on
command:
cumulus@switch:~$ nv set bridge domain br_default svi-force-up enable on
cumulus@switch:~$ nv config apply
- To configure all SVIs on the switch to be perpetually DOWN, run the
nv set system global svi-force-up enable off
command. - To configure the SVIs in a specific bridge to be perpetually DOWN, run the
nv set bridge domain <bridge> svi-force-up enable off
command.
To configure the SVIs in a bridge to be perpetually UP, edit the /etc/network/interfaces
file and add the bridge-always-up on
option to the bridge stanza, then reload the configuration with the sudo ifreload -a
command:
cumulus@switch:~$ sudo nano /etc/network/interfaces
auto br_default
iface br_default
bridge-ports bond1 bond2 bond3 peerlink
hwaddress 48:b0:2d:4e:ad:89
bridge-vlan-aware yes
bridge-vids 10 20 30
bridge-pvid 1
bridge-stp yes
bridge-mcsnoop no
bridge-always-up on
mstpctl-forcevers rstp
cumulus@switch:~$ sudo ifreload -a
To configure all SVIs on the switch to be perpetually UP, add the bridge-always-up on
option to all bridge stanzas with SVIs.
- To configure the SVIs in a bridge to be perpetually DOWN, remove the
bridge-always-up on
option from the bridge stanza, then reload the configuration with thesudo ifreload -a
command. - To configure all SVIs on the switch to be perpetually DOWN, remove the
bridge-always-up on
option from all bridge stanzas, then reload the configuration with thesudo ifreload -a
command.
With the svi-force-up
(bridge-always-up
) option set to on
, even when an interface is down, the bridge remains UP:
cumulus@switch:~$ ip link show bond1
7: bond1: <BROADCAST,MULTICAST,MASTER> mtu 9216 qdisc noqueue master br_default state DOWN mode DEFAULT group default qlen 1000
link/ether 48:b0:2d:cf:e4:3e brd ff:ff:ff:ff:ff:ff
cumulus@switch:~$ ip link show br_default
18: br_default: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 8:b0:2d:4e:ad:89 brd ff:ff:ff:ff:ff:ff
To show if the svi-force-up
option is set to on
for all SVIs on the switch, run the nv show system global svi-force-up
command:
cumulus@switch:~$ nv show system global svi-force-up
operational applied
------ ----------- -------
enable on on
To show if the svi-force-up
option is set to on
for SVIs in a specific bridge, run the nv show bridge domain <domain-id> svi-force-up
command:
cumulus@switch:~$ nv show bridge domain br_default svi-force-up
applied
------ -------
enable on
IPv6 Link-local Address Generation
By default, Cumulus Linux automatically generates IPv6 link-local addresses on VLAN interfaces. If you want to use a different mechanism to assign link-local addresses, you can disable this feature. You can disable link-local automatic address generation for both regular IPv6 addresses and address-virtual (macvlan) addresses.
To disable automatic address generation for a regular IPv6 address on a VLAN, run the following command. The following example command disables automatic address generation for a regular IPv6 address on VLAN 10.
Edit the /etc/network/interfaces
file to add the line ipv6-addrgen off
to the VLAN stanza, then run the ifreload -a
command.
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto vlan10
iface vlan 10
ipv6-addrgen off
vlan-id 10
vlan-raw-device br_default
...
cumulus@switch:~$ ifreload -a
To reenable automatic link-local address generation for a VLAN:
/etc/network/interfaces
file to remove the line ipv6-addrgen off
from the VLAN stanza, then run the ifreload -a
command.MAC Address for a Bridge
To configure a MAC address for a bridge, run the nv set bridge domain <bridge> mac-address <mac-address>
command.
The following example configures the bridge br_default
with MAC address 00:00:5E:00:53:00
:
cumulus@switch:~$ nv set bridge domain br_default mac-address 00:00:5E:00:53:00
cumulus@switch:~$ nv config apply
To unset the MAC address for a bridge, run the nv unset bridge domain <bridge> mac-address <mac-address>
command.
cumulus@switch:~$ nv unset bridge domain br_default mac-address
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file to add the MAC address (hwaddress
) to the bridge stanza, then run the sudo ifreload -a
command.
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
bridge-ports bond1 bond2 bond3 peerlink vxlan48
hwaddress 00:00:5E:00:53:00
bridge-vlan-aware yes
bridge-vids 10 20 30
cumulus@switch:~$ sudo ifreload -a
To unset the MAC address for a bridge, remove the MAC address from the bridge stanza and run the sudo ifreload -a
command.
MAC Address Ageing
By default, Cumulus Linux stores MAC addresses in the Ethernet switching table for 1800 seconds (30 minutes). You can change this setting to a value between 0 and 65535. A value of 0 disables MAC learning and frames flood out of all ports in a VLAN.
The following command example changes the MAC ageing setting to 600 seconds:
cumulus@switch:~$ nv set bridge domain br_default ageing 600
cumulus@switch:~$ nv config apply
Edit the /etc/network/interfaces
file to add the bridge-ageing
parameter to the bridge interface:
cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
bridge-ageing 600
...
To show the bridge ageing configuration setting, run the nv show bridge domain <domain>
command or the Linux sudo ip -d link show <bridge-domain>
command.
cumulus@switch:~$ nv show bridge domain br_default
operational applied
--------------- ----------- ----------
ageing 600
encap 802.1Q
mac-address auto
type vlan-aware
untagged 1
vlan-vni-offset 0
...
To reset bridge ageing to the default value (1800 seconds), run the nv unset bridge domain <domain> ageing
command.
Static MAC Address Entries
You can add a static MAC address entry to the layer 2 table for an interface within the VLAN-aware bridge by running a command similar to the following:
cumulus@switch:~$ sudo bridge fdb add 12:34:56:12:34:56 dev swp1 vlan 150 master static sticky
cumulus@switch:~$ sudo bridge fdb show
44:38:39:00:00:7c dev swp1 master bridge permanent
12:34:56:12:34:56 dev swp1 vlan 150 sticky master bridge static
44:38:39:00:00:7c dev swp1 self permanent
12:12:12:12:12:12 dev swp1 self permanent
12:34:12:34:12:34 dev swp1 self permanent
12:34:56:12:34:56 dev swp1 self permanent
12:34:12:34:12:34 dev bridge master bridge permanent
44:38:39:00:00:7c dev bridge vlan 500 master bridge permanent
12:12:12:12:12:12 dev bridge master bridge permanent
Troubleshooting
To show the ports mapped to each bridge, run the NVUE nv show bridge port
command or the Linux bridge link show
command:
cumulus@switch:~$ nv show bridge port
domain port
-------- ------------------------------
br_default swp1,swp2,swp3
To show port information for a specific bridge, run the NVUE nv show bridge domain <domain-name> port
command:
cumulus@switch:~$ nv show bridge domain br_default port
port flags state
---- -------------------------- ----------
swp1 flood,learning,mcast_flood forwarding
swp2 flood,learning,mcast_flood forwarding
swp3 flood,learning,mcast_flood forwarding
To show the VLANs mapped to each bridge port, run the NVUE nv show bridge port-vlan
command or the Linux bridge vlan show
command:
cumulus@switch:~$ nv show bridge port-vlan
domain port vlan tag-state
------- --------- --------- ---------
br_default swp1 10 untagged
swp2 1 untagged
10 tagged
20 tagged
30 tagged
swp3 1 untagged
10 tagged
20 tagged
30 tagged
To show VLAN information for a specific bridge, run the NVUE nv show bridge domain <domain-name> port vlan
command or the Linux bridge -d vlan show
command:
cumulus@switch:~$ nv show bridge domain br_default port vlan
port vlan tag-state fwd-state
---- ---- --------- ----------
swp1 10 untagged forwarding
swp2 1 untagged forwarding
10 tagged forwarding
20 tagged forwarding
30 tagged forwarding
swp3 1 untagged forwarding
10 tagged forwarding
20 tagged forwarding
30 tagged forwarding
Example Configuration
The following example configuration contains an access port (swp51), a trunk carrying all VLANs (swp3 thru swp48), and a trunk pruning some VLANs from a switch port (swp2).
cumulus@switch:mgmt:~$ nv set interface swp3-48 bridge domain br_default
cumulus@switch:mgmt:~$ nv set bridge domain br_default vlan 310,700,707,712,850,910
cumulus@switch:mgmt:~$ nv set interface swp1 bridge domain br_default access 310
cumulus@switch:mgmt:~$ nv set interface swp1 bridge domain br_default stp bpdu-guard on
cumulus@switch:mgmt:~$ nv set interface swp1 bridge domain br_default stp admin-edge on
cumulus@switch:mgmt:~$ nv set interface swp2 bridge domain br_default vlan 707,712,850
cumulus@switch:mgmt:~$ nv set interface swp2 bridge domain br_default stp admin-edge on
cumulus@switch:mgmt:~$ nv set interface swp2 bridge domain br_default stp bpdu-guard on
cumulus@switch:mgmt:~$ nv set interface swp49 bridge domain br_default stp network on
cumulus@switch:mgmt:~$ nv set interface swp50 bridge domain br_default stp network on
cumulus@switch:mgmt:~$ nv config apply
cumulus@switch:mgmt:~$ sudo cat /etc/nvue.d/startup.yaml
- set:
bridge:
domain:
br_default:
vlan:
'310': {}
'700': {}
'707': {}
'712': {}
'850': {}
'910': {}
interface:
swp1:
bridge:
domain:
br_default:
access: 310
stp:
admin-edge: on
bpdu-guard: on
type: swp
swp2:
bridge:
domain:
br_default:
stp:
admin-edge: on
bpdu-guard: on
vlan:
'707': {}
'712': {}
'850': {}
type: swp
...
swp49:
bridge:
domain:
br_default:
stp:
network: on
type: swp
swp50:
bridge:
domain:
br_default:
stp:
network: on
type: swp
system:
hostname: switch
cumulus@switch:mgmt:~$ sudo cat /etc/network/interfaces
...
auto lo
iface lo inet loopback
auto mgmt
iface mgmt
address 127.0.0.1/8
address ::1/128
vrf-table auto
auto eth0
iface eth0 inet dhcp
ip-forward off
ip6-forward off
vrf mgmt
# the following is an access port
auto swp1
iface swp1
bridge-access 310
mstpctl-bpduguard yes
mstpctl-portadminedge yes
# the following is a trunk port that is pruned
# only .1q tags of 707, 712, 850 are sent and received
auto swp2
iface swp2
bridge-vids 707 712 850
mstpctl-bpduguard yes
mstpctl-portadminedge yes
...
# the following port is the trunk uplink and inherits all vlans
# from br_default; bridge assurance is enabled using portnetwork
auto swp49
iface swp49
mstpctl-portnetwork yes
# the following port is the trunk uplink and inherits all vlans
# from 'br_default'; bridge assurance is enabled using portnetwork
auto swp50
iface swp50
mstpctl-portnetwork yes
# ports swp3-swp48 are trunk ports that inherit vlans
# 310,700,707,712,850,910 from the bridge br_default
auto br_default
iface br_default
bridge-ports swp1 swp2 swp3... swp49 swp50
hwaddress 44:38:39:22:01:af
bridge-vlan-aware yes
bridge-vids 310 700 707 712 850 910
bridge-pvid 1
Considerations
Spanning Tree Protocol (STP)
- By default, STP runs in RSTP mode on a per-bridge basis. To configure STP to run in PVRST mode, where each VLAN runs its own instance of STP, see PVRST Mode for a VLAN-aware Bridge.
mstpd
remains the user space protocol daemon.
VLAN Translation
You cannot enable VLAN translation on a bridge in VLAN-aware mode. Only traditional mode bridges support VLAN translation.
Bridge Conversion
You cannot convert traditional mode bridges automatically to and from a VLAN-aware bridge. You must delete the original configuration and bring down all member switch ports before creating a new bridge.
VLAN Memory Resource Limitations
On Spectrum-2 and later, Cumulus Linux uses internal debugging flow counters for each VLAN that require KVD and ATCAM memory space. When you configure more than 1000 VLAN interfaces, you might not be able to apply ACLs if flow counter resources deplete the ACL resource space. In addition, you might see error messages in the /var/log/switchd.log
file similar to the following:
error: hw sync failed (sync_acl hardware installation failed) Rolling back .. failed.
error: hw sync failed (Bulk counter init failed with No More Resources). Rolling back ..
To troubleshoot this issue and manage netfilter resources with high VLAN and ACL scale, refer to Troubleshooting ACL Rule Installation Failures.