Set Up Your KVM Virtual Machine for a Single Remote Server

Follow these steps to setup and configure your VM on a single server in a cloud deployment:

  1. Verify that your system meets the VM requirements.

    ResourceMinimum Requirements
    ProcessorFour (4) virtual CPUs
    Memory8 GB RAM
    Local disk storage64 GB
    Network interface speed1 Gb NIC
    HypervisorKVM/QCOW (QEMU Copy on Write) image for servers running CentOS, Ubuntu, and RedHat operating systems
  2. Confirm that the needed ports are open for communications.

    You must open the following ports on your NetQ on-premises server:
    Port or Protocol NumberProtocolComponent Access
    4IP ProtocolCalico networking (IP-in-IP Protocol)
    179TCPCalico networking (BGP)
    443TCPNetQ UI
    2379TCPetcd datastore
    4789UDPCalico networking (VxLAN)
    5000TCPDocker registry
    31980TCPNetQ Agent communication
    31982TCPNetQ Agent SSL communication
    32708TCPAPI Gateway

    Port 32666 is no longer used for the NetQ UI.

  3. Download the NetQ images.

    1. On the NVIDIA Application Hub, log in to your account.
    2. Select NVIDIA Licensing Portal.
    3. Select Software Downloads from the menu.
    4. Click Product Family and select NetQ.
    5. Locate the NetQ SW 4.1 KVM Cloud image and select Download.
    6. If prompted, agree to the license agreement and proceed with the download.

    For enterprise customers, if you do not see a link to the NVIDIA Licensing Portal on the NVIDIA Application Hub, contact NVIDIA support.

    For NVIDIA employees, download NetQ directly from the NVIDIA Licensing Portal.

  4. Setup and configure your VM.

    Open your hypervisor and set up your VM. You can use this example for reference or use your own hypervisor instructions.

    KVM Example Configuration

    This example shows the VM setup process for a system with Libvirt and KVM/QEMU installed.

    1. Confirm that the SHA256 checksum matches the one posted on the Cumulus Downloads website to ensure the image download has not been corrupted.

      $ sha256sum ./Downloads/netq-4.0.0-ubuntu-18.04-tscloud-qemu.qcow2
      $ FE353FC06D3F843F4041D74C853D38B0A56036C5886F6233A3ED1A9464AEB783 ./Downloads/netq-4.0.0-ubuntu-18.04-tscloud-qemu.qcow2
    2. Copy the QCOW2 image to a directory where you want to run it.

      Tip: Copy, instead of moving, the original QCOW2 image that was downloaded to avoid re-downloading it again later should you need to perform this process again.

      $ sudo mkdir /vms
      $ sudo cp ./Downloads/netq-4.0.0-ubuntu-18.04-tscloud-qemu.qcow2 /vms/ts.qcow2
    3. Create the VM.

      For a Direct VM, where the VM uses a MACVLAN interface to sit on the host interface for its connectivity:

      $ virt-install --name=netq_ts --vcpus=4 --memory=8192 --os-type=linux --os-variant=generic --disk path=/vms/ts.qcow2,format=qcow2,bus=virtio,cache=none --network=type=direct,source=eth0,model=virtio --import --noautoconsole

      Replace the disk path value with the location where the QCOW2 image is to reside. Replace network model value (eth0 in the above example) with the name of the interface where the VM is connected to the external network.

      Or, for a Bridged VM, where the VM attaches to a bridge which has already been setup to allow for external access:

      $ virt-install --name=netq_ts --vcpus=4 --memory=8192 --os-type=linux --os-variant=generic \ --disk path=/vms/ts.qcow2,format=qcow2,bus=virtio,cache=none --network=bridge=br0,model=virtio --import --noautoconsole

      Replace network bridge value (br0 in the above example) with the name of the (pre-existing) bridge interface where the VM is connected to the external network.

      Make note of the name used during install as this is needed in a later step.

    4. Watch the boot process in another terminal window.
      $ virsh console netq_ts
  5. Log in to the VM and change the password.

    Use the default credentials to log in the first time:

    • Username: cumulus
    • Password: cumulus
    $ ssh cumulus@<ipaddr>
    Warning: Permanently added '<ipaddr>' (ECDSA) to the list of known hosts.
    Ubuntu 18.04.5 LTS
    cumulus@<ipaddr>'s password:
    You are required to change your password immediately (root enforced)
    System information as of Thu Dec  3 21:35:42 UTC 2020
    System load:  0.09              Processes:           120
    Usage of /:   8.1% of 61.86GB   Users logged in:     0
    Memory usage: 5%                IP address for eth0: <ipaddr>
    Swap usage:   0%
    WARNING: Your password has expired.
    You must change your password now and login again!
    Changing password for cumulus.
    (current) UNIX password: cumulus
    Enter new UNIX password:
    Retype new UNIX password:
    passwd: password updated successfully
    Connection to <ipaddr> closed.

    Log in again with your new password.

    $ ssh cumulus@<ipaddr>
    Warning: Permanently added '<ipaddr>' (ECDSA) to the list of known hosts.
    Ubuntu 18.04.5 LTS
    cumulus@<ipaddr>'s password:
      System information as of Thu Dec  3 21:35:59 UTC 2020
      System load:  0.07              Processes:           121
      Usage of /:   8.1% of 61.86GB   Users logged in:     0
      Memory usage: 5%                IP address for eth0: <ipaddr>
      Swap usage:   0%
    Last login: Thu Dec  3 21:35:43 2020 from <local-ipaddr>
  6. Verify the platform is ready for installation. Fix any errors indicated before installing the NetQ software.

    cumulus@hostname:~$ sudo opta-check-cloud
  7. Change the hostname for the VM from the default value.

    The default hostname for the NetQ Virtual Machines is ubuntu. Change the hostname to fit your naming conventions while meeting Internet and Kubernetes naming standards.

    Kubernetes requires that hostnames are composed of a sequence of labels concatenated with dots. For example, “” is a hostname. Each label must be from 1 to 63 characters long. The entire hostname, including the delimiting dots, has a maximum of 253 ASCII characters.

    The Internet standards (RFCs) for protocols specify that labels may contain only the ASCII letters a through z (in lower case), the digits 0 through 9, and the hyphen-minus character ('-').

    Use the following command:

    cumulus@hostname:~$ sudo hostnamectl set-hostname NEW_HOSTNAME

    Add the same NEW_HOSTNAME value to /etc/hosts on your VM for the localhost entry. Example: localhost NEW_HOSTNAME
  8. Run the Bootstrap CLI. Be sure to replace the eth0 interface used in this example with the interface on the server used to listen for NetQ Agents.

    cumulus@:~$ netq bootstrap master interface eth0 tarball /mnt/installables/netq-bootstrap-4.1.0.tgz

    Allow about five to ten minutes for this to complete, and only then continue to the next step.

    If this step fails for any reason, you can run netq bootstrap reset and then try again.

    If you have changed the IP address or hostname of the NetQ Cloud VM after this step, you need to re-register this address with NetQ as follows:

    Reset the VM.

    cumulus@hostname:~$ netq bootstrap reset

    Re-run the Bootstrap CLI. This example uses interface eth0. Replace this with your updated IP address, hostname or interface using the interface or ip-addr option.

    cumulus@:~$ netq bootstrap master interface eth0 tarball /mnt/installables/netq-bootstrap-4.1.0.tgz
  9. Consider the following for container environments, and make adjustments as needed.

    Flannel Virtual Networks

    If you are using Flannel with a container environment on your network, you may need to change its default IP address ranges if they conflict with other addresses on your network. This can only be done one time during the first installation.

    The address range is NetQ overrides the original Flannel default, which is

    To change the default address range, use the CLI with the pod-ip-range option. For example:

    cumulus@hostname:~$ netq bootstrap master interface eth0 tarball /mnt/installables/netq-bootstrap-4.1.0.tgz pod-ip-range
    Docker Default Bridge Interface

    The default Docker bridge interface is disabled in NetQ. If you need to reenable the interface, contact support.

The final step is to install and activate the NetQ software. You can do this using the Admin UI or the CLI.

Click the installation and activation method you want to use to complete installation: