4001098
| When you use NetQ LCM to upgrade a Cumulus Linux switch from version 5.9 to 5.10, and if the upgrade fails, NetQ rolls back to version 5.9 and reverts the cumulus user password to the default password. After rollback, reconfigure the password with the nv set system aaa user cumulus password <password> command. | 4.11.0-4.13.0 | |
3995266
| When you use NetQ LCM to upgrade a Cumulus Linux switch with NTP configured using NVUE in a VRF that is not mgmt, the upgrade fails to complete. To work around this issue, first unset the NTP configuration with the nv unset service ntp and nv config apply commands, and reconfigure NTP after the upgrade completes. | 4.11.0-4.13.0 | |
3993243
| When you upgrade your NetQ VM, RoCE validation data might not contain all RoCE-enabled switches in your network. This condition will clear within 24 hours of the NetQ upgrade. | 4.10.0-4.13.0 | |
3985598
| When you configure multiple threshold-crossing events for the same TCA event ID on the same device, NetQ will only display one TCA event for each hostname per TCA event ID, even if both thresholds are crossed or status events are triggered. | 4.11.0-4.13.0 | |
3983871
| When you run the netq install command on a VM with an IP address configured that overlaps the NetQ pod or service IP subnets 10.244.0.0/16 or 10.96.0.0/16, the install prechecks will fail but subsequent attempts to run netq install will fail even after changing the VM IP address to not conflict with these subnets. To work around this issue, run the netq bootstrap reset purge-db command and rerun the netq install command. | 4.11.0-4.13.0 | |
3981655
| When you upgrade your NetQ VM, some devices in the NetQ inventory might appear as rotten. To work around this issue, restart NetQ agents on devices or upgrade them to the latest agent version after the NetQ VM upgrade is completed. | 4.11.0-4.13.0 | |
3858210
| When you upgrade your NetQ VM, DPUs in the inventory are not shown. To work around this issue, restart the DTS container on the DPUs in your network. | 4.10.0-4.13.0 | |
3854467
| When a single NetQ cluster VM is offline, the NetQ kafka-connect pods are brought down on other cluster nodes, preventing NetQ data from collecting data. To work around this issue, bring all cluster nodes back into service. | 4.10.0-4.13.0 | |
3847280
| The netq-opta package fails to install on Cumulus Linux 5.9.0. On-switch OPTA is not supported on Cumulus Linux 5.9.0. | 4.10.0-4.13.0 | |
3800434
| When you upgrade NetQ from a version prior to 4.9.0, What Just Happened data that was collected before the upgrade is no longer present. | 4.9.0-4.13.0 | |
3772274
| After you upgrade NetQ, data from snapshots taken prior to the NetQ upgrade will contain unreliable data and should not be compared to any snapshots taken after the upgrade. In cluster deployments, snapshots from prior NetQ versions will not be visible in the UI. | 4.9.0-4.13.0 | |
3771279
| When an interface speed is changed in the network, NetQ might not reflect the new speed until up to an hour after the change. | 4.11.0-4.13.0 | |
3769936
| When there is a NetQ interface validation failure for admin state mismatch, the validation failure might clear unexpectedly while one side of the link is still administratively down. | 4.9.0-4.13.0 | |
3752422
| When you run a NetQ trace and specify MAC addresses for the source and destination, NetQ displays the message “No valid path to destination” and does not display trace data. | 4.9.0-4.13.0 | |
3613811
| LCM operations using in-band management are unsupported on switches that use eth0 connected to an out-of-band network. To work around this issue, configure NetQ to use out-of-band management in the mgmt VRF on Cumulus Linux switches when interface eth0 is in use. | 4.8.0-4.13.0 | |
Download all 4.11 release notes as .xls