Set Up Your VMware Virtual Machine for a Single On-premises Server

Follow these steps to set up and configure your VM on a single server in an on-premises deployment:

  1. Verify that your system meets the VM requirements.

    ResourceMinimum Requirements
    ProcessorSixteen (16) virtual CPUs
    Memory64 GB RAM
    Local disk storage500 GB SSD with minimum disk IOPS of 1000 for a standard 4kb block size
    (Note: This must be an SSD; use of other storage options can lead to system instability and are not supported.)
    Network interface speed1 Gb NIC
    HypervisorVMware ESXi™ 6.5 or later (OVA image) for servers running Cumulus Linux, CentOS, Ubuntu, and RedHat operating systems
  2. Confirm that the required ports are open for communications.

    You must open the following ports on your NetQ on-premises server:
    Port or Protocol NumberProtocolComponent Access
    4IP ProtocolCalico networking (IP-in-IP Protocol)
    22TCPSSH
    80TCPNginx
    179TCPCalico networking (BGP)
    443TCPNetQ UI
    2379TCPetcd datastore
    4789UDPCalico networking (VxLAN)
    5000TCPDocker registry
    6443TCPkube-apiserver
    30001TCPDPU communication
    31980TCPNetQ Agent communication
    31982TCPNetQ Agent SSL communication
    32708TCPAPI Gateway
  3. Download the NetQ image.

    1. On the NVIDIA Application Hub, log in to your account.
    2. Select NVIDIA Licensing Portal.
    3. Select Software Downloads from the menu.
    4. Click Product Family and select NetQ.
    5. Locate the NetQ SW 4.12 VMware image and select Download.
    6. If prompted, read the license agreement and proceed with the download.

    For enterprise customers, if you do not see a link to the NVIDIA Licensing Portal on the NVIDIA Application Hub, contact NVIDIA support.


    For NVIDIA employees, download NetQ directly from the NVIDIA Licensing Portal.

  4. Set up and configure your VM.

    VMware Example Configuration This example shows the VM setup process using an OVA file with VMware ESXi.
    1. Enter the address of the hardware in your browser.

    2. Log in to VMware using credentials with root access.

    3. Click Storage in the Navigator to verify you have an SSD installed.

    4. Click Create/Register VM at the top of the right pane.

    5. Select Deploy a virtual machine from an OVF or OVA file, and click Next.

    6. Provide a name for the VM, for example NetQ.

      Tip: Make note of the name used during install as this is needed in a later step.

    7. Drag and drop the NetQ Platform image file you downloaded in Step 1 above.

    8. Click Next.

    9. Select the storage type and data store for the image to use, then click Next. In this example, only one is available.

    10. Accept the default deployment options or modify them according to your network needs. Click Next when you are finished.

    11. Review the configuration summary. Click Back to change any of the settings, or click Finish to continue with the creation of the VM.

      The progress of the request is shown in the Recent Tasks window at the bottom of the application. This may take some time, so continue with your other work until the upload finishes.

    12. Once completed, view the full details of the VM and hardware.

  5. Log in to the VM and change the password.

    Use the default credentials to log in the first time:

    • Username: cumulus
    • Password: cumulus
    $ ssh cumulus@<ipaddr>
    Warning: Permanently added '<ipaddr>' (ECDSA) to the list of known hosts.
    Ubuntu 20.04 LTS
    cumulus@<ipaddr>'s password:
    You are required to change your password immediately (root enforced)
    System information as of Thu Dec  3 21:35:42 UTC 2020
    System load:  0.09              Processes:           120
    Usage of /:   8.1% of 61.86GB   Users logged in:     0
    Memory usage: 5%                IP address for eth0: <ipaddr>
    Swap usage:   0%
    WARNING: Your password has expired.
    You must change your password now and login again!
    Changing password for cumulus.
    (current) UNIX password: cumulus
    Enter new UNIX password:
    Retype new UNIX password:
    passwd: password updated successfully
    Connection to <ipaddr> closed.
    

    Log in again with your new password.

    $ ssh cumulus@<ipaddr>
    Warning: Permanently added '<ipaddr>' (ECDSA) to the list of known hosts.
    Ubuntu 20.04 LTS
    cumulus@<ipaddr>'s password:
      System information as of Thu Dec  3 21:35:59 UTC 2020
      System load:  0.07              Processes:           121
      Usage of /:   8.1% of 61.86GB   Users logged in:     0
      Memory usage: 5%                IP address for eth0: <ipaddr>
      Swap usage:   0%
    Last login: Thu Dec  3 21:35:43 2020 from <local-ipaddr>
    cumulus@ubuntu:~$
    
  6. Verify the platform is ready for installation. Fix any errors indicated before installing the NetQ software.

    cumulus@hostname:~$ sudo opta-check
  7. Change the hostname for the VM from the default value.

    The default hostname for the NetQ Virtual Machines is ubuntu. Change the hostname to fit your naming conventions while meeting Internet and Kubernetes naming standards.

    Kubernetes requires that hostnames are composed of a sequence of labels concatenated with dots. For example, “en.wikipedia.org” is a hostname. Each label must be from 1 to 63 characters long. The entire hostname, including the delimiting dots, has a maximum of 253 ASCII characters.

    The Internet standards (RFCs) for protocols specify that labels may contain only the ASCII letters a through z (in lower case), the digits 0 through 9, and the hyphen-minus character ('-').

    Use the following command:

    cumulus@hostname:~$ sudo hostnamectl set-hostname NEW_HOSTNAME

    Add the same NEW_HOSTNAME value to /etc/hosts on your VM for the localhost entry. Example:

    127.0.0.1 localhost NEW_HOSTNAME
  8. Install and activate the NetQ software using the CLI:

    cumulus@hostname:~$ netq install standalone full interface eth0 bundle /mnt/installables/NetQ-4.12.0.tgz

    NetQ uses the 10.244.0.0/16 (pod-ip-range) and 10.96.0.0/16 (service-ip-range) networks for internal communication by default. If you are using these networks, you must override each range by specifying new subnets for these parameters in the install command:

    cumulus@hostname:~$ netq install standalone full interface eth0 bundle /mnt/installables/NetQ-4.12.0.tgz pod-ip-range <pod-ip-range> service-ip-range <service-ip-range>

    You can specify the IP address of the server instead of the interface name using the ip-addr <ip-address> argument:

    cumulus@hostname:~$ netq install standalone full ip-addr <ip-address> bundle /mnt/installables/NetQ-4.12.0.tgz

    If you change the server IP address or hostname after installing NetQ, you must reset the server with the netq bootstrap reset keep-db command and rerun the install command.

    If this step fails for any reason, you can run netq bootstrap reset and then try again.

    Verify Installation Status

    To view the status of the installation, use the netq show status [verbose] command. The following example shows a successful on-premises installation:

    State: Active
        Version: 4.12.0
        Installer Version: 4.12.0
        Installation Type: Cluster
        Activation Key: PKrgipMGEhVuZXRxLWVuZHBvaW50LWdhdGV3YXkYsagDIixUQmFLTUhzZU80RUdTL3pOT01uQ2lnRnrrUhTbXNPUGRXdnUwTVo5SEpBPTIHZGVmYXVsdDoHbmV0cWRldgz=
        Master SSH Public Key: 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
        Is Cloud: False
        
        Cluster Status:
        IP Address     Hostname       Role    Status
        -------------  -------------  ------  --------
        10.188.44.147  10.188.44.147  Role    Ready
        
        NetQ... Active
        

    Run the netq show opta-health command to verify all applications are operating properly. Allow 10-15 minutes for all applications to come up and report their status.

    cumulus@hostname:~$ netq show opta-health
        Application                                            Status    Namespace      Restarts    Timestamp
        -----------------------------------------------------  --------  -------------  ----------  ------------------------
        cassandra-rc-0-w7h4z                                   READY     default        0           Fri Apr 10 16:08:38 2020
        cp-schema-registry-deploy-6bf5cbc8cc-vwcsx             READY     default        0           Fri Apr 10 16:08:38 2020
        kafka-broker-rc-0-p9r2l                                READY     default        0           Fri Apr 10 16:08:38 2020
        kafka-connect-deploy-7799bcb7b4-xdm5l                  READY     default        0           Fri Apr 10 16:08:38 2020
        netq-api-gateway-deploy-55996ff7c8-w4hrs               READY     default        0           Fri Apr 10 16:08:38 2020
        netq-app-address-deploy-66776ccc67-phpqk               READY     default        0           Fri Apr 10 16:08:38 2020
        netq-app-admin-oob-mgmt-server                         READY     default        0           Fri Apr 10 16:08:38 2020
        netq-app-bgp-deploy-7dd4c9d45b-j9bfr                   READY     default        0           Fri Apr 10 16:08:38 2020
        netq-app-clagsession-deploy-69564895b4-qhcpr           READY     default        0           Fri Apr 10 16:08:38 2020
        netq-app-configdiff-deploy-ff54c4cc4-7rz66             READY     default        0           Fri Apr 10 16:08:38 2020
        ...
        

    If any of the applications or services display Status as DOWN after 30 minutes, open a support ticket and attach the output of the opta-support command.

After NetQ is installed, you can log in to NetQ from your browser.