Install the NetQ On-premises Appliance
This topic describes how to prepare your single, NetQ On-premises Appliance for installation of the NetQ Platform software.
Each system shipped to you contains:
- Your NVIDIA NetQ On-premises Appliance (a Supermicro 6019P-WTR server)
- Hardware accessories, such as power cables and rack mounting gear (note that network cables and optics ship separately)
- Information regarding your order
For more detail about hardware specifications (including LED layouts and FRUs like the power supply or fans, and accessories like included cables) or safety and environmental information, refer to the user manual and quick reference guide.
Install the ApplianceAfter you unbox the appliance:
- Mount the appliance in the rack.
- Connect it to power following the procedures described in your appliance's user manual.
- Connect the Ethernet cable to the 1G management port (eno1).
- Power on the appliance.
If your network runs DHCP, you can configure NetQ over the network. If DHCP is not enabled, then you configure the appliance using the console cable provided.
Configure the Password, Hostname, and IP Address
Change the password and specify the hostname and IP address for the appliance before installing the NetQ software.
Log in to the appliance using the default login credentials:
- Username: cumulus
- Password: cumulus
Change the password using the
cumulus@hostname:~$ passwd Changing password for cumulus. (current) UNIX password: cumulus Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully
The default hostname for the NetQ On-premises Appliance is netq-appliance. Change the hostname to fit your naming conventions while meeting Internet and Kubernetes naming standards.
Kubernetes requires that hostnames comprise a sequence of labels concatenated with dots. For example, en.wikipedia.org is a hostname. Each label must be from 1 to 63 characters long. The entire hostname, including the delimiting dots, has a maximum of 253 ASCII characters.
The Internet standards (RFCs) for protocols specify that labels can contain only the ASCII letters a through z (in lower case), the digits 0 through 9, and the hyphen-minus character ('-').
Use the following command:
cumulus@hostname:~$ sudo hostnamectl set-hostname NEW_HOSTNAME
Identify the IP address.
The appliance contains two Ethernet ports. It uses port eno1 for out-of-band management. This is where NetQ Agents should send the telemetry data collected from your monitored switches and hosts. By default, eno1 uses DHCPv4 to get its IP address. You can view the assigned IP address using the following command:
cumulus@hostname:~$ ip -4 -brief addr show eno1 eno1 UP 10.20.16.248/24
Alternately, you can configure the interface with a static IP address by editing the /etc/netplan/01-ethernet.yaml Ubuntu Netplan configuration file.
For example, to set your network interface eno1 to a static IP address of 192.168.1.222 with gateway 192.168.1.1 and DNS server as 18.104.22.168 and 22.214.171.124:
# This file describes the network interfaces available on your system # For more information, see netplan(5). network: version: 2 renderer: networkd ethernets: eno1: dhcp4: no addresses: [192.168.1.222/24] gateway4: 192.168.1.1 nameservers: addresses: [126.96.36.199,188.8.131.52]
Apply the settings.
cumulus@hostname:~$ sudo netplan apply
Verify NetQ Software and Appliance Readiness
Now that the appliance is up and running, verify that the software is available and the appliance is ready for installation.
Verify that the needed packages are present and of the correct release, version 4.6 and update 38.
cumulus@hostname:~$ dpkg -l | grep netq ii netq-agent 4.6.0-ub20.04u42~1682429296.e13e0426_amd64 Cumulus NetQ Telemetry Agent for Ubuntu ii netq-apps 4.6.0-ub20.04u42~1682429296.e13e0426_amd64 Cumulus NetQ Fabric Validation Application for Ubuntu
Verify the installation images are present and of the correct release, version 4.6.
cumulus@hostname:~$ cd /mnt/installables/ cumulus@hostname:/mnt/installables$ ls NetQ-4.6.0.tgz
Verify the appliance is ready for installation. Fix any errors indicated before installing the NetQ software.
cumulus@hostname:~$ sudo opta-check
The final step is to install and activate the NetQ software using the CLI:
Run the following command on your NetQ platform server:
cumulus@hostname:~$ netq install standalone full interface eth0 bundle /mnt/installables/NetQ-4.6.0.tgz
You can specify the IP address instead of the interface name here: use
ip-addr <IP address> in place of
interface <ifname> above.
If you have changed the IP address or hostname of the NetQ on-premises VM after this step, you need to re-register this address with NetQ as follows:
Reset the VM, indicating whether you want to purge any NetQ DB data or keep it.
cumulus@hostname:~$ netq bootstrap reset [purge-db|keep-db]
Re-run the install CLI on the appliance. This example uses interface eno1. Replace this with your updated IP address, hostname or interface using the interface or ip-addr option.
cumulus@hostname:~$ netq install standalone full interface eno1 bundle /mnt/installables/NetQ-4.6.0.tgz
If this step fails for any reason, you can run
netq bootstrap reset and then try again.
Verify Installation Status
To view the status of the installation, use the
netq show status [verbose] command. The following example shows a successful on-premises installation:
State: Active Version: 4.6.0 Installer Version: 4.6.0 Installation Type: Standalone Activation Key: PKrgipMGEhVuZXRxLWVuZHBvaW50LWdhdGV3YXkYsagDIixUQmFLTUhzZU80RUdTL3pOT01uQ2lnRnrrUhTbXNPUGRXdnUwTVo5SEpBPTIHZGVmYXVsdDoHbmV0cWRldgz= Master SSH Public Key: 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 Is Cloud: False Cluster Status: IP Address Hostname Role Status ------------- ------------- ------ -------- 10.188.44.147 10.188.44.147 Role Ready NetQ... Active
netq show opta-health command to verify all applications are operating properly. Allow 10-15 minutes for all applications to come up and report their status.
cumulus@hostname:~$ netq show opta-health Application Status Namespace Restarts Timestamp ----------------------------------------------------- -------- ------------- ---------- ------------------------ cassandra-rc-0-w7h4z READY default 0 Fri Apr 10 16:08:38 2020 cp-schema-registry-deploy-6bf5cbc8cc-vwcsx READY default 0 Fri Apr 10 16:08:38 2020 kafka-broker-rc-0-p9r2l READY default 0 Fri Apr 10 16:08:38 2020 kafka-connect-deploy-7799bcb7b4-xdm5l READY default 0 Fri Apr 10 16:08:38 2020 netq-api-gateway-deploy-55996ff7c8-w4hrs READY default 0 Fri Apr 10 16:08:38 2020 netq-app-address-deploy-66776ccc67-phpqk READY default 0 Fri Apr 10 16:08:38 2020 netq-app-admin-oob-mgmt-server READY default 0 Fri Apr 10 16:08:38 2020 netq-app-bgp-deploy-7dd4c9d45b-j9bfr READY default 0 Fri Apr 10 16:08:38 2020 netq-app-clagsession-deploy-69564895b4-qhcpr READY default 0 Fri Apr 10 16:08:38 2020 netq-app-configdiff-deploy-ff54c4cc4-7rz66 READY default 0 Fri Apr 10 16:08:38 2020 ...
If any of the applications or services display Status as DOWN after 30 minutes, open a support ticket and attach the output of the
After NetQ is installed, you can log in to NetQ from your browser.