Physical Interfaces Commands
Use the CLI to monitor OSI Layer 1 physical components on network devices, including interfaces, ports, links, and peers. You can monitor transceivers and cabling deployed per port (interface), per vendor, per part number, and so forth.
This information can help you:
- Determine which ports are empty versus which ones have cables plugged in to help validate expected connectivity.
- Audit transceiver and cable components by vendor, helping you estimate replacement costs, repair costs, and overall maintenance costs.
- Identify mismatched links.
- Identify when physical layer changes (for example, bonds and links going down or flapping) occurred.
NetQ uses LLDP (Link Layer Discovery Protocol) to collect port information. NetQ can also identify peer ports connected to DACs (Direct Attached Cables) and AOCs (Active Optical Cables) without using LLDP, even if the link is not UP.
View performance and status information about cables, transceiver modules, and interfaces with netq show interfaces physical:
netq show interfaces physical
View Utilization Statistics Networkwide
Utilization statistics can indicate whether resources are becoming dangerously close to their maximum capacity or other, user-defined thresholds. Depending on the function of the switch, the acceptable thresholds can vary.
Compute Resources Utilization
View how many compute resources—CPU, disk, and memory—the switches on your network consume with netq show resource-util:
netq show resource-util
View statistics about a given node and interface, including frame errors, ACL drops, and buffer drops with netq show ethtool-stats:
netq show ethtool-stats
Interface Statistics and Utilization
NetQ Agents collect performance statistics every 30 seconds for the physical interfaces on switches in your network. The NetQ Agent does not collect statistics for non-physical interfaces, such as bonds, bridges, and VXLANs. The NetQ Agent collects the following statistics:
- Transmit: tx_bytes, tx_carrier, tx_colls, tx_drop, tx_errs, tx_packets
- Receive: rx_bytes, rx_drop, rx_errs, rx_frame, rx_multicast, rx_packets
- rx_util, tx_util
- port speed
netq show interface-stats
netq show interface-utilization
ACL Resource Utilization Networkwide
View incoming and outgoing access control lists (ACLs) configured on all switches and host with netq show cl-resource acl:
netq show cl-resource acl
Forwarding Resources Utilization Networkwide
View forwarding resources on all devices with netq show cl-resource forwarding:
netq show cl-resource forwarding
SSD Utilization Networkwide
For NetQ Appliances that have 3ME3 solid state drives (SSDs) installed (primarily in on-premises deployments), you can view the utilization of the drive on demand. A warning is generated when a drive drops below 10% health, or has more than a 2% loss of health in 24 hours, indicating the need to rebalance the drive. Tracking SSD utilization over time lets you see any downward trend or drive instability before you receive a warning message.
View SDD utilization with netq show cl-ssd-util:
netq show cl-ssd-util
Disk Storage After BTRFS Allocation Networkwide
Customers running Cumulus Linux 3 which uses the BTRFS (b-tree file system) might experience issues with disk space management. This is a known problem of BTRFS because it does not perform periodic garbage collection, or rebalancing. If left unattended, these errors can make it impossible to rebalance the partitions on the disk. To avoid this issue, NVIDIA recommends rebalancing the BTRFS partitions in a preemptive manner, but only when absolutely needed to avoid reduction in the lifetime of the disk. By tracking the state of the disk space usage, users can determine when to rebalance.
For details about when to rebalance a partition, refer to When to Rebalance BTRFS Partitions.
View BTRFS disk utilization with netq show cl-btrfs-info:
netq show cl-btrfs-info
Link Interface Commands
View interface (link) state, type, count, aliases, and additional information with variations of the netq show interfaces command, including netq show interfaces type and netq show events message_type interfaces:
netq show interfaces
netq show interfaces type
netq show events message_type interfaces
The netq check interfaces command verifies interface communication status for all nodes (leafs, spines, and hosts) or an interface between specific nodes in your network fabric. This command only checks the physical interfaces; it does not check bridges, bonds, or other software constructs.
netq check interfaces
View Link Interfaces in the UI
You can monitor the same information outlined in the section above via the UI by expanding the Menu, then selecting Interfaces.
Check for MTU Inconsistencies
The maximum transmission unit (MTU) determines the largest size packet or frame that can be transmitted across a given communication link. When the MTU is not configured to the same value on both ends of the link, communication problems can occur. Use the netq check mtu command to verify that the MTU is correctly specified for each link.