Link on Physical Switch Port Does not Come Up
Issue
The link on a physical switch port — an interface starting with “swp” — does not come up.
Environment
- Cumulus Linux, all versions
Resolution
Here is a list of things to check:
Use Suggested Optics, Cables, Transceivers
Read the pluggables section of the HCL for recommendations on which optics, cables and transceivers to use with your platform.
Ensure Your Cumulus Linux License Is Valid
Until you install a valid Cumulus Linux license, none of the physical switch ports come up, so they do not appear in the output of ip link show.
$ sudo cl-license
No license installed!
Read this article for additional details on how to address this.
Bring the Link Up with ip link set
Check the output of ip link show, you should see the following:
Physical state: UP
Admin state: UP
LOWER_UP
cumulus@switch$ ip link show swp1 3: swp1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc pfifo_fast state UP mode DEFAULT qlen 500 link/ether c4:54:44:4f:ab:00 brd ff:ff:ff:ff:ff:ff
If the physical switch port shows as DOWN instead of UP, configure the interface to be UP with the ip link set command:
cumulus@switch$ ip link show swp3
5: swp3: <BROADCAST,MULTICAST> mtu 9000 qdisc pfifo_fast master vlan5 state DOWN mode DEFAULT qlen 500
link/ether c4:54:44:4f:ab:00 brd ff:ff:ff:ff:ff:ff
cumulus@switch$ sudo ip link set swp3 up
cumulus@switch$ ip link show swp3
5: swp3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc pfifo_fast master vlan5 state UP mode DEFAULT qlen 500
link/ether c4:54:44:4f:ab:00 brd ff:ff:ff:ff:ff:ff
To make this persistent after reboot so the port is up, define the swp in the /etc/network/interfaces file (using net add interface swp3 link up); you can also automate this with Mako, as documented in this article.
cumulus@switch$ net add interface swp3 link up
cumulus@switch$ net commit
Ensure Physical Connections Are Good
In the output of ip link show, if you see NO_CARRIER instead of LOWER_UP, there is no physical link.
cumulus@switch$ ip link show swp21
23: swp21: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 9000 qdisc pfifo_fast master vlan5 state DOWN mode DEFAULT qlen 500
link/ether c4:54:44:4f:ab:12 brd ff:ff:ff:ff:ff:ff
Check your connections, reseat the pluggable and verify cables.
Explicitly Configure the Port Speed, Duplex Mode, Auto Negotiation Settings
You might need to explicitly configure the physical switch port attributes, especially in scenarios where ports might allow different types of pluggables or where someone reconfigured the attribute. The following attributes might need to be explicitly configured:
- link-speed
- link-duplex
- link-autoneg
For example, you can configure the following in /etc/network/interfaces:
auto swp1
iface swp1
address 10.1.1.1/24
mtu 9000
link-speed 10000
link-duplex full
link-autoneg off
Note that if the interface name starts with swp and ends with _sX, where X is a number between 0 and 3, then this is a 10G connection in a breakout Twinax or AOC cable.
cumulus@switch$ ip link show swp32s0
37: swp32s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 500
link/ether 00:e0:ec:27:ab:9b brd ff:ff:ff:ff:ff:ff
cumulus@switch$ grep swp32s0 /var/lib/cumulus/porttab
swp32s0 xe34 0 0
cumulus@switch$ grep xe34 /etc/bcm.d/config.bcm
port_init_speed_xe34=10000
port_init_autoneg_xe34=0
serdes_if_type_xe34=9
Read Switch Port Attributes for more details on how to configure the physical switch port attributes.
Validate Hardware Settings with ethtool
The ethtool command enables you to query or control the network driver and hardware settings. It takes the device name (like swp1) as an argument, for example:
cumulus@switch$ ethtool swp1
cumulus@switch$ sudo ethtool -m swp1
Read Monitoring Interfaces and Transceivers Using ethtool for more details on ethtool.
Force the Interface Configurations to Be Pushed to Hardware
Ensure the configuration in /etc/network/interfaces gets pushed to hardware. Run the following command:
cumulus@switch$ sudo ifreload -a