BFD
The nv unset commands remove the configuration you set with the equivalent nv set commands. This guide only describes an nv unset command if it differs from the nv set command.
nv set interface <interface-id> router ospf bfd profile <profile-name>
Configures the BFD profile to use for an OSPF interface.
When you enable BFD on an OSPF interface, a neighbor registers with BFD when two-way adjacency starts and de-registers when adjacency goes down. The BFD configuration is per interface and any IPv4 neighbors discovered on that interface inherit the configuration.
Command Syntax
| Syntax | Description |
|---|---|
<interface-id> | The interface you want to configure. |
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set interface swp1 router ospf bfd profile BFD1
nv set interface <interface-id> router pim bfd profile <profile-name>
Configures the BFD profile to use for a PIM interface.
Command Syntax
| Syntax | Description |
|---|---|
<interface-id> | The interface you want to configure. |
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set interface swp1 router pim bfd profile BFD1
nv set router bfd state
Enables and disables BFD globally on the switch.
BFD provides low overhead and rapid detection of failures in the paths between two network devices. It provides a unified mechanism for link detection over all media and protocol layers. Use BFD to detect failures for IPv4 and IPv6 single or multihop paths between any two network devices, including unidirectional path failure detection.
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd state enabled
nv set router bfd profile <profile-name>
Configures the BFD profile.
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1
nv set router bfd profile <profile-name> detect-multiplier
Configures the detection time multiplier to determine packet loss. The detection timeout is calculated based on multiplying the detection multiplier with the greater value between the local switch’s receive interval and the peer’s transmit interval. The default value is 3.
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1 detect-multiplier 10
nv set router bfd profile <profile-name> min-rx-interval
Configures the minimum interval between the received BFD control packets. You can set a value between 10 and 4294967 milliseconds. The default value is 300.
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1 min-rx-interval 100
nv set router bfd profile <profile-name> min-tx-interval
Configures the minimum interval for transmitting BFD control packets. You can set a value between 10 and 4294967 milliseconds. The default value is 300.
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1 min-tx-interval 100
nv set router bfd profile <profile-name> minimum-ttl
Configures the minimum expected TTL for an incoming BFD control packet (for multi hop sessions only). This feature tightens the packet validation requirements to avoid receiving BFD control packets from other sessions. You can set a value between 1 and 254. The default value is 254 (only expect one hop between this system and the peer).
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1 minimum-ttl 1
nv set router bfd profile <profile-name> passive-mode
Configures passive mode, which marks the session as passive. A passive session does not attempt to start the connection and waits for control packets from the peer before it begins replying. Passive mode is useful when you have a router that acts as the central node of a star network and you want to avoid sending BFD control packets you don’t need to. You can set passive mode to enabled or disabled. The default is disabled.
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1 passive-mode enabled
nv set router bfd profile <profile-name> shutdown
Configures the BFD shutdown, which enables or disables the peer. When the peer is disabled, the switch sends an administrative down message to the remote peer. The default value is disabled.
Command Syntax
| Syntax | Description |
|---|---|
\<profile-name\> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set router bfd profile BFD1 shutdown enabled
nv set vrf <vrf-id> router bgp peer-group <peer-group-id> bfd profile <profile-name>
Configures BFD for a peer group using the specified BFD profile.
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<peer-group-id> | The peer group name. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router bgp peer-group fabric bfd profile BFD1
nv set vrf <vrf-id> router bgp neighbor <neighbor-id> bfd profile <profile-name>
Configures BFD for a neighbor using the specified BFD profile.
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<neighbor-id> | The VRF name. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router bgp neighbor swp51 bfd profile BFD1
nv set vrf <vrf-id> router static <ipv4-prefix> distance <integer> via <ipv4> bfd profile <profile-name>
Associates static routes with BFD to monitor static route reachability. Depending on status of the BFD session, the switch either adds or removes static routes from the Routing Information Base (RIB).
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<ipv4-prefix> | The IPv4 prefix. |
<integer> | The IPv4 prefix. |
<ipv4> | The IPv4 prefix. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router static 10.10.10.101/32 distance 2 via 10.0.1.0 bfd profile BFD2
nv set vrf <vrf-id> router static <ipv4-prefix> distance <integer> via <ipv4> bfd multi-hop
Configures BFD for multihop next-hop tracking through static routes. You can specify enabled or disabled. BFD operates in single hop mode by default.
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<ipv4-prefix> | The IPv4 prefix. |
<integer> | The IPv4 prefix. |
<ipv4> | The IPv4 prefix. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router static 10.10.10.101/32 distance 2 via 10.0.1.0 bfd multi-hop enabled
nv set vrf <vrf-id> router static <ipv4-prefix> distance <integer> via <ipv4> bfd source
Configures the BFD source for static routes.
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<ipv4-prefix> | The IPv4 prefix. |
<integer> | The IPv4 prefix. |
<ipv4> | The IPv4 prefix. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router static 10.10.10.101/32 distance 2 via 10.0.1.0 bfd source 10.10.10.3
nv set vrf <vrf-id> router static <ipv4-prefix> via <ipv4> bfd profile <profile-name>
Associates static routes with BFD to monitor static route reachability. Depending on status of the BFD session, the switch either adds or removes static routes from the Routing Information Base (RIB).
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<ipv4-prefix> | The IPv4 prefix. |
<ipv4> | The IPv4 prefix. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router static 10.10.10.101/32 via 10.0.1.0 bfd profile BFD1
nv set vrf <vrf-id> router static <ipv4-prefix> via <ipv4> bfd multi-hop
Configures BFD for multihop next-hop tracking through static routes. You can specify enabled or disabled. BFD operates in single hop mode by default.
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<ipv4-prefix> | The IPv4 prefix. |
<ipv4> | The IPv4 prefix. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router static 10.10.10.101/32 via 10.0.1.0 bfd multi-hop enabled
nv set vrf <vrf-id> router static <ipv4-prefix> via <ipv4> bfd source
Configures the BFD source for static routes.
Command Syntax
| Syntax | Description |
|---|---|
<vrf-id> | The VRF name. |
<ipv4-prefix> | The IPv4 prefix. |
<ipv4> | The IPv4 prefix. |
Version History
Introduced in Cumulus Linux 5.15.0
Example
cumulus@switch:~$ nv set vrf default router static 10.10.10.101/32 distance 2 via 10.0.1.0 bfd source 10.10.10.3