QoS
The nv unset
commands remove the configuration you set with the equivalent nv set
commands. This guide only describes an nv unset
command if it differs from the nv set
command.
nv set interface <interface-id> qos
Configures QoS on the specified interface.
nv set interface <interface-id> qos congestion-control
Configures QoS congestion control on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos congestion-control
nv set interface <interface-id> qos congestion-control profile <profile-name>
Configures the QoS congestion control profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos congestion-control profile MYPROFILE
nv set interface <interface-id> qos egress-scheduler
Configures QoS egress scheduling on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos egress-scheduler
nv set interface <interface-id> qos egress-scheduler profile <profile-name>
Configures the QoS egress scheduler profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos egress-scheduler profile MYPROFILE
nv set interface <interface-id> qos egress-shaper
Configures QoS egress shaping on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos egress-shaper
nv set interface <interface-id> qos egress-shaper profile <profile-name>
Configures the QoS egress scheduler profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos egress-shaper profile MYPROFILE
nv set interface <interface-id> qos link-pause
Configures QoS link pause on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos link-pause
nv set interface <interface-id> qos link-pause profile <profile-name>
Configures the QoS link pause profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos link-pause profile
nv set interface <interface-id> qos mapping
Configures QoS mapping on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set interface swp1 qos mapping
nv set interface <interface-id> qos mapping profile <profile-name>
Configures the QoS mapping profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set interface swp1 qos mapping profile MYPROFILE
nv set interface <interface-id> qos pfc
Configures QoS PFC on the specifies interface.
nv set interface <interface-id> qos pfc profile <profile-name>
Configures the QoS PFC profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set interface swp1 qos pfc profile MYPROFILE
nv set interface <interface-id> qos remark
Configures QoS remarking on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos remark
nv set interface <interface-id> qos remark profile <profile-name>
Configures the QoS mapping profile on the specified interface.
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
<profile-name> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set interface swp1 qos remark profile MYPROFILE
nv set interface <interface-id> qos pfc-watchdog state
Enables or disables PFC watchdog on the interface. PFC watchdog detects and mitigates pause storms on ports where PFC or link pause is ON. The default setting is disable
.
- PFC watchdog only works for lossless traffic queues.
- You can only configure PFC watchdog on a port with PFC (or link pause) configuration.
- You can only enable PFC watchdog on a physical interface (swp).
- You cannot enable the watchdog on a bond (for example, bond0) but you can enable the watchdog on a port that is a member of a bond (for example, swp1).
Command Syntax
Syntax | Description |
---|---|
<interface-id> | The interface you want to configure. |
Version History
Introduced in Cumulus Linux 5.6.0
Example
cumulus@switch:~$ nv set interface swp1 qos qos pfc-watchdog state enable
nv set qos
Configures global Quality of Service (QOS) settings.
nv set qos advance-buffer-config <profile-id>
Configures the QoS advanced buffer profile settings. Advanced buffer configuration can override the base traffic-pool profiles configured on the system.
nv set qos advance-buffer-config <profile-id> egress-lossless-buffer
Configures egress lossless buffer settings.
nv set qos advance-buffer-config <profile-id> egress-lossless-buffer reserved
Configures the reserved buffer allocation in bytes for the egress lossless buffer. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossless-buffer reserved 10000
nv set qos advance-buffer-config <profile-id> egress-lossless-buffer service-pool <integer>
Configures the service pool for the egress lossless buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossless-buffer service-pool 3
nv set qos advance-buffer-config <profile-id> egress-lossless-buffer shared-alpha
Configures the dynamic shared buffer alpha allocation in bytes for the egress lossless buffer. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossless-buffer shared-alpha 10000
nv set qos advance-buffer-config <profile-id> egress-lossless-buffer shared-bytes
Configures the static shared buffer allocation in bytes for the egress lossless buffer. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossless-buffer shared-bytes 10000
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer
Configures the egress lossy buffer.
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-port
Configures the multicast port for the egress lossy buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer multicast-port
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-port reserved
Configures the reserved multicast port buffer allocation in bytes for the egress lossy buffer. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossless-buffer reserved 10000
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-port shared-bytes
Configures the multicast port static buffer allocation in bytes for the egress lossy buffer. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossless-buffer shared-bytes 10000
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-switch-priority <qos-sp-id>
Configures the multicast switch priority for the egress lossy buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-sp-id> | The multicast switch priority. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer multicast-switch-priority 5,7
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-switch-priority <qos-sp-id> reserved
Configures the reserved buffer allocation in bytes for the egress lossy buffer multicast switch priority. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-sp-id> | The multicast switch priority. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer multicast-switch-priority 5,7
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-switch-priority <qos-sp-id> service-pool <integer>
Configures the service pool ID for the egress lossy buffer multicast switch priority.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-sp-id> | The multicast switch priority. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer multicast-switch-priority 5,7 service-pool 3
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-switch-priority <qos-sp-id> shared-alpha
Configures the dynamic shared buffer alpha allocation for the egress lossy buffer multicast switch priority.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-sp-id> | The multicast switch priority. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer multicast-switch-priority 5,7 shared-alpha alpha_2
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer multicast-switch-priority <qos-sp-id> shared-bytes
Configures the static shared buffer allocation in bytes for the egress lossy buffer multicast switch priority. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-sp-id> | The multicast switch priority. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer multicast-switch-priority 5,7 shared-bytes 10000
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer traffic-class <traffic-class-id>
Configures the traffic classes for the egress lossy buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<traffic-class-id> | The traffic class ID. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer traffic-class 3
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer traffic-class <traffic-class-id> reserved
Configures the reserved buffer allocation in bytes for the egress lossy buffer traffic class. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<traffic-class-id> | The traffic class ID. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer traffic-class 3 reserved 10000
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer traffic-class <traffic-class-id> service-pool <integer>
Configures the service pool ID for the egress lossy buffer traffic class.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<traffic-class-id> | The traffic class ID. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer traffic-class 3 service-pool 3
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer traffic-class <traffic-class-id> shared-alpha
Configures the dynamic shared buffer alpha allocation for the egress lossy buffer traffic class.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<traffic-class-id> | The traffic class ID. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer traffic-class 3 shared-alpha alpha_2
nv set qos advance-buffer-config <profile-id> egress-lossy-buffer traffic-class <traffic-class-id> shared-bytes
Configures the static shared buffer allocation in bytes for the egress lossy buffer traffic class. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<traffic-class-id> | The traffic class ID. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-lossy-buffer traffic-class 3 shared-bytes 10000
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id>
Configures the QoS egress service pool ID.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool ID. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id> infinite
Configures the egress service pool flag to infinite. You can specify true
or false
. The default setting is false
.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3 infinite true
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id> memory-percent
Configures the egress service pool memory percent allocation. You can specify a value between 0 and 100. The sum of memory-percent
values across all egress pools must be less than or equal to 100 percent.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3 memory-percent 20
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id> mode
Configures the egress service pool mode. You can specify static
or dynamic
.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3 mode dynamic
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id> reserved
Configures the egress service pool reserved buffer allocation in bytes. You can specify a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3 reserved 10000
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id> shared-alpha
Configures the egress service pool dynamic shared buffer alpha allocation.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3 shared-alpha alpha_1_4
nv set qos advance-buffer-config <profile-id> egress-pool <pool-id> shared-bytes
Configures the egress service pool static shared buffer allocation in bytes. You can specify a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-pool 3 shared-bytes 10000
nv set qos advance-buffer-config <profile-id> ingress-lossless-buffer
Configures the ingress lossless buffer settings.
nv set qos advance-buffer-config <profile-id> ingress-lossless-buffer service-pool <integer>
Configures the service pool for the ingress lossless buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossless-buffer service-pool 3
nv set qos advance-buffer-config <profile-id> ingress-lossless-buffer shared-alpha
Configures the dynamic shared buffer alpha allocation for the ingress lossless buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossless-buffer shared-alpha alpha_1_8
nv set qos advance-buffer-config <profile-id> ingress-lossless-buffer shared-bytes
Configures the static shared buffer allocation in bytes for the ingress lossless buffer. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossless-buffer shared-bytes 10000
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer
Configures the ingress lossy buffer.
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id>
Configures the priority group alias name for the ingress lossy buffer.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id> name <value>
Configures an alias name for the ingress lossy buffer priority group.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 name SERVERS
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id> reserved
Configures the reserved buffer allocation in bytes for the ingress lossy buffer priority group. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 reserved 10000
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id> service-pool <integer>
Configures the service pool for the ingress lossy buffer priority group.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 service-pool 2
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id> shared-alpha
Configures dynamic shared buffer alpha allocation in bytes for the ingress lossy buffer priority group. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 shared-alpha 10000
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id> shared-bytes
Configures the static shared buffer allocation in bytes for the ingress lossy buffer priority group. You can set a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 shared-bytes 10000
nv set qos advance-buffer-config <profile-id> ingress-lossy-buffer priority-group <priority-group-id> switch-priority <qos-sp-id>
Configures the switch priority for the ingress lossy buffer priority group.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
<qos-sp-id> | The switch priority. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 switch-priority 0,1,3,4,5,6,7
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id>
Configures the QoS ingress service pool name.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id> infinite
Configures the ingress service pool flag to infinite. You can specify true
or false
. The default setting is false
.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 infinite true
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id> memory-percent
Configures the ingress service pool memory percent allocation. You can specify a value between 0 and 100. The sum of memory-percent
values across all ingress pools must be less than or equal to 100 percent.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 memory-percent 20
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id> mode
Configures the ingress service pool mode. You can specify static
or dynamic
.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 mode dynamic
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id> reserved
Configures the ingress service pool reserved buffer allocation in bytes. You can specify a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 reserved 10000
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id> shared-alpha
Configures the ingress service pool dynamic shared buffer alpha allocation.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 shared-alpha alpha_1_4
nv set qos advance-buffer-config <profile-id> ingress-pool <pool-id> shared-bytes
Configures the ingress service pool static shared buffer allocation in bytes. You can specify a value between 0 and 4294967295.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<pool-id> | The pool name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 shared-bytes 10000
nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group <priority-group> headroom
Configures the lossy headroom for a specified priority group. Lossy headroom is the buffer on top of the reserved buffer that stores packets that ingress the switch. You can configure the lossy headroom to help analyze performance for a specific priority group.
The switch calculates the default value internally based on the MTU and internal latency.
Command Syntax
Syntax | Description |
---|---|
<priority-group-id> | The priority group alias name. In Cumulus Linux 5.10 and later, you can specify bulk , and service1 through service7 . In Cumulus Linux 5.9 and earlier, you can specify bulk , control , and service1 through service6 . |
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossy-buffer priority-group service1 headroom 50000
nv set qos advance-buffer-config <profile-id> egress-mgmt-buffer reserved
Configures the egress management reserved buffer allocation in bytes.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-mgmt-buffer reserved 30000
nv set qos advance-buffer-config <profile-id> egress-mgmt-buffer service-pool
Configures the QoS egress management buffer service pool mapping. You can specify a value between 0 and 7.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-mgmt-buffer service-pool 0
nv set qos advance-buffer-config <profile-id> egress-mgmt-buffer shared-alpha
Configures the dynamic egress management shared buffer alpha allocation. You can specify one of these values: alpha_0
, alpha_1_128
, alpha_1_64
, alpha_1_32
, alpha_1_16
, alpha_1_8
, alpha_1_4
, alpha_1_2
, alpha_1
, alpha_2
, alpha_4
, alpha_8
, alpha_16
, alpha_32
, alpha_64
, or alpha_infinity
.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-mgmt-buffer shared-alpha alpha_2
nv set qos advance-buffer-config <profile-id> egress-mgmt-buffer shared-bytes
Configures the QoS static egress management shared buffer allocation in bytes.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global egress-mgmt-buffer shared-bytes 14000
nv set qos advance-buffer-config <profile-id> ingress-mgmt-buffer headroom
Configures the QoS ingress management buffer headroom in bytes.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-mgmt-buffer headroom 10000
nv set qos advance-buffer-config <profile-id> ingress-mgmt-buffer service-pool
Configures the QoS ingress management buffer service pool mapping. You can specify a value between 0 and 7.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-mgmt-buffer service-pool 0
nv set qos advance-buffer-config <profile-id> ingress-mgmt-buffer shared-alpha
Configures the QoS dynamic ingress management shared buffer alpha allocation. You can specify one of these values: alpha_0
, alpha_1_128
, alpha_1_64
, alpha_1_32
, alpha_1_16
, alpha_1_8
, alpha_1_4
, alpha_1_2
, alpha_1
, alpha_2
, alpha_4
, alpha_8
, alpha_16
, alpha_32
, alpha_64
, or alpha_infinity
.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-mgmt-buffer shared-alpha alpha_2
nv set qos advance-buffer-config <profile-id> ingress-mgmt-buffer shared-bytes
Configures the static ingress management shared buffer allocation in bytes.
Version History
Introduced in Cumulus Linux 5.10.0
Example
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-mgmt-buffer shared-bytes 14000
nv set qos congestion-control <profile-id>
Configures ECN; an end-to-end flow control technology. Instead of telling adjacent devices to stop transmitting during times of buffer congestion, ECN sets the ECN bits of the transit IPv4 or IPv6 header to indicate to end hosts that congestion might occur. As a result, the sending hosts reduce their sending rate until the transit switch no longer sets ECN bits.
ECN operates by having a transit switch that marks packets between two end hosts. You use ECN with RDMA over Converged Ethernet (RoCE).
nv set qos congestion-control <profile-id> traffic-class <qos-tc-id>
Configures traffic class settings for the specified ECN profile.
nv set qos congestion-control <profile-id> traffic-class <qos-tc-id> ecn
Turns ECN bit marking on or off for the traffic class in the specified ECN profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 ecn enable
nv set qos congestion-control <profile-id> traffic-class <qos-tc-id> max-threshold <value>
Configures the maximum buffer threshold in bytes. Cumulus Linux marks all ECN-capable packets when buffer congestion crosses this threshold.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 max-threshold 200000
nv set qos congestion-control <profile-id> traffic-class <qos-tc-id> min-threshold <value>
Configures the minimum buffer threshold in bytes. Random ECN marking starts when buffer congestion crosses this threshold. The probability determines if ECN marking occurs.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 min-threshold 40000
nv set qos congestion-control <profile-id> traffic-class <qos-tc-id> probability
Configures the probability that Cumulus Linux marks an ECN-capable packet when buffer congestion is between the minimum threshold and the maximum threshold. You can set a value between 1 and 100.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 probability 80
nv set qos congestion-control <profile-id> traffic-class <qos-tc-id> red
Turns RED on or off.
ECN prevents packet drops in the network due to congestion by signaling hosts to transmit less. However, if congestion continues after ECN marking, packets drop after the switch buffer is full. By default, Cumulus Linux tail-drops packets when the buffer is full. You can enable RED to drop packets that are in the queue randomly instead of always dropping the last arriving packet. This might improve overall performance of TCP based flows.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 red enable
nv set qos egress-queue-mapping <profile-id>
Configures egress queues. Cumulus Linux supports eight egress queues to provide different classes of service. By default switch priority values map directly to the matching egress queue. For example, switch priority value 0 maps to egress queue 0.
You can remap queues by changing the switch priority value to the corresponding queue value. You can map multiple switch priority values to a single egress queue.
nv set qos egress-queue-mapping <profile-id> switch-priority <qos-sp-id>
Configures the switch priority for the egress queue profile.
nv set qos egress-queue-mapping <profile-id> switch-priority <qos-sp-id> traffic-class
Configures the switch priority to egress queue mapping.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-sp-id> | The switch priority. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos egress-queue-mapping default-global switch-priority 2 traffic-class 7
nv set qos egress-scheduler <profile-id>
Configures the egress scheduler. Cumulus Linux supports 802.1Qaz, Enhanced Transmission Selection, which allows the switch to assign bandwidth to egress queues and then schedule the transmission of traffic from each queue. 802.1Qaz supports Priority Queuing.
Cumulus Linux provides a default egress scheduler that applies to all ports, where the bandwidth allocated to egress queues 0,2,4,6 is 12 percent and the bandwidth allocated to egress queues 1,3,5,7 is 13 percent.
nv set qos egress-scheduler <profile-id> traffic-class <qos-tc-id>
Configures the traffic class for the specified egress scheduler profile. The traffic class defines the egress queue where you want to assign bandwidth. For example, traffic-class 2 defines the bandwidth allocation for egress queue 2.
nv set qos egress-scheduler <profile-id> traffic-class <qos-tc-id> bw-percent
Configures the bandwidth percent value between 1 and 100 for the specified egress queue. If you do not specify a value for an egress queue, Cumulus Linux uses a DWRR value of 0 (no egress scheduling). The combined total of values you assign must be less than or equal to 100.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 2,6 bw-percent 30
nv set qos egress-scheduler <profile-id> traffic-class <qos-tc-id> mode
Configures the traffic class mode (dwrr
or strict
) for the specified egress scheduler profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 2,6 mode dwrr
nv set qos egress-shaper <profile-id>
Configures traffic shaping, which allows a switch to send traffic at an average bitrate lower than the physical interface. Traffic shaping prevents a receiving device from dropping bursty traffic if the device is either not capable of that rate of traffic or has a policer that limits what it accepts.
Traffic shaping works by holding packets in the buffer and releasing them at specific time intervals.
nv set qos egress-shaper <profile-id> port-max-rate
Configures the maximum packet shaper rate for the specified profile. You can set a value between 0 and 2147483647.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos egress-shaper shaper1 port-max-rate 2000
nv set qos egress-shaper <profile-id> traffic-class <qos-tc-id>
Configures the traffic class (egress queue) for the specified traffic shaper profile.
nv set qos egress-shaper <profile-id> traffic-class <qos-tc-id> max-rate
Configures the maximum bandwidth for the specified egress queue for a traffic shaper profile. You can set a value between 0 and 2147483647.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos egress-shaper shaper1 traffic-class 2 max-rate 500
nv set qos egress-shaper <profile-id> traffic-class <qos-tc-id> min-rate
Configures the minimum bandwidth for the specified egress queue for a traffic shaper profile. You can set a value between 0 and 2147483647.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-tc-id> | The traffic class (egress queue). |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos egress-shaper shaper1 traffic-class 2 min-rate 100
nv set qos link-pause <profile-id>
Configures QoS link pause; an older congestion control mechanism that causes all traffic on a link between two switches, or between a host and switch, to stop transmitting during times of congestion. Pause frames start and stop depending on buffer congestion. You configure pause frames on a per-direction, per-interface basis. You can receive pause frames to stop the switch from transmitting when requested, send pause frames to request neighboring devices to stop transmitting, or both.
Before configuring pause frames, you must first modify the switch buffer allocation.
nv set qos link-pause <profile-id> cable-length
Configures the cable length in meters for the specified link pause profile. You can specify a value between 1 and 100000.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos link-pause my_pause_ports cable-length 50
nv set qos link-pause <profile-id> port-buffer <value>
Configures the port buffer allocation in bytes for the specified link pause profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos link-pause my_pause_ports port-buffer 20000
nv set qos link-pause <profile-id> rx
Turns receiving pause frames on and off.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos link-pause my_pause_ports rx disable
nv set qos link-pause <profile-id> tx
Turns sending pause frames on and off.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos link-pause my_pause_ports tx enable
nv set qos link-pause <profile-id> xoff-threshold <value>
Configures the frame transmission stop threshold in bytes for the specified link pause profile.
NVIDIA recommends that you do not change this setting but, instead, let Cumulus Linux configure the settings dynamically. Only change the threshold setting if you are an advanced user who understands the buffer configuration requirements for lossless traffic to work seamlessly.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos link-pause my_pause_ports xoff-threshold 1000
nv set qos link-pause <profile-id> xon-threshold <value>
Configures the frame transmission start threshold in bytes for the specified link pause profile.
NVIDIA recommends that you do not change these settings but, instead, let Cumulus Linux configure the settings dynamically. Only change the threshold this setting if you are an advanced user who understands the buffer configuration requirements for lossless traffic to work seamlessly.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos link-pause my_pause_ports xon-threshold 1000
nv set qos mapping <profile-id>
Configures trust 802.1p and DSCP marking.
When a frame or packet arrives on the switch, Cumulus Linux maps it to an internal COS (switch priority) value. This value never writes to the frame or packet but classifies and schedules traffic internally through the switch.
You can define the trusted values: 802.1p, DSCP, or both.
nv set qos mapping <profile-id> dscp <qos-dscp-id>
Configures trust DSCP marking.
nv set qos mapping <profile-id> dscp <qos-dscp-id> switch-priority
Configures the DSCP to switch priority mapping.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-dscp-id> | The DSCP value. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos mapping default-global dscp 10,21,36 switch-priority 0
nv set qos mapping <profile-id> pcp <qos-pcp-id>
Configures trust 802.1p marking.
nv set qos mapping <profile-id> pcp <qos-pcp-id> switch-priority
Configures the 802.1p to switch priority mapping.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
<qos-pcp-id> | The 802.1p value. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos mapping default-global pcp 0 switch-priority 4
nv set qos mapping <profile-id> port-default-sp
Assigns all traffic to a specific switch priority regardless of the ingress marking.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos mapping default-global port-default-sp 3
nv set qos mapping <profile-id> trust
Configures the port trust. You can specify l2
, l3
, port
, or both
.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos mapping default-global trust l3
nv set qos pfc <profile-id>
Configures Priority flow control (PFC) settings. PFC extends the capabilities of pause frames by the frames for a specific 802.1p value instead of stopping all traffic on a link. If a switch supports PFC and receives a PFC pause frame for a given 802.1p value, the switch stops transmitting frames from that queue, but continues transmitting frames for other queues.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global
nv set qos pfc <profile-id> cable-length
Configures the cable length in meters for the specified PFC profile. You can specify a value between 1 and 100000.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global cable-length 50
nv set qos pfc <profile-id> port-buffer <value>
Configures the port buffer allocation in bytes for the specified PFC profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global port-buffer 20000
nv set qos pfc <profile-id> rx
Turns receiving PFC frames on and off.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global rx enable
nv set qos pfc <profile-id> switch-priority <qos-sp-id>
Configures the switch priority for the specified PFC profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global switch-priority 0
nv set qos pfc <profile-id> tx
Turns sending PFC frames on and off.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global tx enable
nv set qos pfc <profile-id> xoff-threshold <value>
Configures the frame transmission stop threshold in bytes for the specified PFC profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global xoff-threshold 1000
nv set qos pfc <profile-id> xon-threshold <value>
Configures the frame transmission start threshold in bytes for the specified PFC profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos pfc default-global xon-threshold 10000
nv set qos remark <profile-id>
Configures 802.1p or DSCP traffic marking.
nv set qos remark <profile-id> rewrite
You can specify l2
, l3
, or both
.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos remark default-global rewrite
nv set qos remark <profile-id> switch-priority <qos-sp-id>
Configures switch priority to 802.1p or DSCP traffic marking.
nv set qos remark <profile-id> switch-priority <qos-sp-id> dscp
Configures switch priority to egress DSCP mapping for the specified remark profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos remark default-global switch-priority 0 dscp 22
nv set qos remark <profile-id> switch-priority <qos-sp-id> pcp
Configures switch priority to egress 802.1p (PCP) mapping for the specified remark profile.
Command Syntax
Syntax | Description |
---|---|
<profile-id> | The profile name. |
Version History
Introduced in Cumulus Linux 5.4.0
Example
cumulus@switch:~$ nv set qos remark default-global switch-priority 0 pcp 4
nv set qos roce
Configures RDMA over Converged Ethernet lossless (RoCE).
nv set qos roce cable-length
Configures the cable length for RoCE lossless. You can specify a value between 1 and 100000. The default setting is 100 meters.
Version History
Introduced in Cumulus Linux 5.0.0
Example
cumulus@switch:~$ nv set qos roce cable-length 1000
nv set qos roce enable
Turns QoS RoCE on or off on the switch. The default setting is off
.
Version History
Introduced in Cumulus Linux 5.0.0
Example
cumulus@switch:~$ nv set qos roce enable off
nv set qos roce mode
Configures the RoCE mode. You can specify lossy
or lossless
. The default setting is lossless
.
Version History
Introduced in Cumulus Linux 5.0.0
Example
cumulus@switch:~$ nv set qos roce mode lossy
nv set qos traffic-pool <traffic-pool-id>
Configures the Q0S traffic pool ID.
Command Syntax
Syntax | Description |
---|---|
<traffic-pool-id> | The traffic pool ID. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos traffic-pool 3
nv set qos traffic-pool <traffic-pool-id> memory-percent
Configures the percent of memory allocated to the specified traffic pool.
Command Syntax
Syntax | Description |
---|---|
<traffic-pool-id> | The traffic pool ID. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos traffic-pool 3 memory percent 80
nv set qos traffic-pool <traffic-pool-id> switch-priority <qos-sp-id>
Configures the QoS switch priority for the specified traffic pool.
Command Syntax
Syntax | Description |
---|---|
<traffic-pool-id> | The traffic pool ID. |
Version History
Introduced in Cumulus Linux 5.3.0
Example
cumulus@switch:~$ nv set qos traffic-pool 3
nv set qos pfc-watchdog polling-interval
Configures the PFC watchdog polling interval. The default polling interval is 100 milliseconds.
Version History
Introduced in Cumulus Linux 5.6.0
Example
cumulus@switch:~$ nv set qos pfc-watchdog polling-interval 200
nv set qos pfc-watchdog robustness
Configures how many polling intervals the PFC watchdog must wait before it mitigates the storm condition. The default number of polling intervals is 3.
Version History
Introduced in Cumulus Linux 5.6.0
Example
cumulus@switch:~$ nv set qos pfc-watchdog robustness 5