Create Content

image image image image image

On This Page

interface ethernet


interface ethernet <slot>/<port>[/<subport>][-<slot>/<port>[/<subport>]]

Enters the Ethernet interface or Ethernet interface range configuration mode.

Syntax Description<slot>/<port>Ethernet port number
subportEthernet subport number to be used if a port is split
DefaultN/A
Configuration Modeconfig
History3.1.0000
3.2.1100Added range support
Example
switch (config) # interface ethernet 1/1
switch (config interface ethernet 1/1) # exit
switch (config) # interface ethernet 1/1-1/10
switch (config interface ethernet 1/1-1/10) #
Related Commands
Notes



boot-delay


boot-delay [<time>]
no boot-delay

Configures interface boot-delay timer.
The no form of the command returns boot-delay time to its default value.

Syntax DescriptiontimeBoot delay time in seconds
Range: 0-600
Default0 seconds
Configuration Modeconfig interface ethernet
config interface port-channel
config interface mlag-port-channel
History3.6.2002
Example
switch (config interface ethernet 1/1) # boot-delay 60
Related Commandsshow interfaces ethernet
Notes
  • This command delays the interface from boot time of the interface
  • Configuration save and system reboot is required for the configuration to take effect



description


description <string>
no description

Configures an interface description.
The no form of the command returns the interface description to its default value.

Syntax Descriptionstring40 bytes
Default""
Configuration Modeconfig interface ethernet
config interface port-channel
config interface mlag-port-channel
History3.1.0000
3.3.4500Added MPO configuration mode
Example
switch (config interface ethernet 1/1) # description my-interface
Related Commandsshow interfaces ethernet
Notes




fec-override


fec-override <fec-configuration> [force]
no fec-override <fec-configuration> [force]

Changes FEC configuration on a specific port or range of ports.
The no form of the command resets this parameter to its default value.

Syntax Descriptionfec-configuration
  • fc-fec FireCode FEC
  • no-fec does not use FEC
  • rs-fec Reed Solomon FEC
force
DefaultAuto-FEC selection
Configuration Modeconfig interface ethernet
History3.5.0000
3.6.2002Added force option
3.7.1000Updated Example
Example
switch (config interface ethernet 1/1) # fec-override fc-fec
Related Commandsshow interfaces ethernet
Notes

Use this command with caution. There is no limitation in configuring non-standard FEC. It may cause the link to malfunction.



flowcontrol


flowcontrol {receive | send} {off | on} [force]

Enables or disables IEEE 802.3x link-level flow control per direction for the specified interface.

Syntax Descriptionreceive | send
  • receive ingresses direction

  • send egresses direction

off | on
  • on enables IEEE 802.3x link-level flow control for the specified interface on receive or send
  • off disables IEEE 802.3x link-level flow control for the specified interface on receive or send
forceForces configuration without the need to toggle the interface
Defaultreceive off; send off
Configuration Mode

config interface ethernet
config interface port-channel
config interface mlag-port-channel

History3.1.0000
3.3.4500Added MPO configuration mode
Example
switch (config interface ethernet 1/1) # flowcontrol receive on
Related Commandsshow interfaces ethernet
Notes

To configure global pause please see section “Flowcontrol (Global pause)”.



ip address dhcp


ip address dhcp
no ip address dhcp

Enables DHCP on this Ethernet interface.

Syntax DescriptionN/A
DefaultDisabled
Configuration Mode

config interface ethernet set as router interface
config interface port-channel set as router interface

History3.4.2008
Example
switch (config interface ethernet 1/1) # ip address dhcp
Related Commandsshow interfaces ethernet
Notes




load-interval


load-interval <time>
no load-interval

Sets the interface counter interval.
The no form of the command resets the interval to its default value.

Syntax DescriptiontimeIn seconds
Default300 seconds
Configuration Mode

config interface ethernet
config interface port-channel
config interface mlag-port-channel

History3.3.0000
3.3.4500Added MPO configuration mode
Example
switch (config interface ethernet 1/1) # load-interval 30
Related Commandsshow interfaces ethernet
Notes

This interval is used for the ingress rate and egress rate counters



module-type


module-type <type> [force]
no module-type <type> [force]

Splits the interface to two or four separate interfaces, or merges them back to a single interface (QSFP).
The no form of the command resets the interface to its default configuration.

Syntax Description

type

  • qsfp - Port runs at 40000/56000Mbps
  • qsfp-split-2 - Port is split and runs at 2X10000Mb/s
  • qsfp-split-4 - Port is split and runs at 4X10000Mb/s

force

Force the split operation without asking for user confirmation.

Default

QSFP

Configuration Mode

config interface ethernet

History

3.1.1400


3.5.0000

Added note

3.6.3640

Added note

3.6.4006

Added note

Example

switch (config interface ethernet 1/4) # module-type qsfp-split-4
The following interfaces will be unmapped: 1/4 1/1
Type 'yes' to confirm split: yes

Related Commands

show interfaces ethernet

Notes

  • Port cannot be split when storm-control is configured on port
  • Force command don't remove storm-control configuration. Error output:
    % Storm control configuration must be removed from interface Eth1/2
  • After a split port is created or deleted, the forwarding mode for each split port is set according to the global configuration
  • The affected interfaces should be disabled prior to the operation
  • In order to unsplit the interface, use the command with “qsfp”, the speed is set to 40Gb/s “module-type qsfp”
  • The following speeds are supported on the different Ethernet interface types:
    • qsfp 1G, 10G, 25G, 40G, 50G, 56G, 100G
    • qsfp-split-2 1G, 10G, 25G, 50G
    • qsfp-split-4 1G, 10G, 25G



mtu


mtu <frame-size>

Configures the Maximum Transmission Unit (MTU) frame size for the interface.

Syntax Description

frame-size

Range: 1500-9216 bytes

Default

1500 bytes

Configuration Mode

config interface ethernet
config interface port-channel
config interface mlag-port-channel

History

3.1.0000


3.3.4500

Added MPO configuration mode

Example

switch (config interface ethernet 1/4) # mtu 9216

Related Commands

show interfaces ethernet

Notes




shutdown


shutdown
no shutdown

Disables the interface.
The no form of the command enables the interface.

Syntax DescriptionN/A

Default

Interface is enabled

Configuration Mode

config interface ethernet
config interface port-channel
config interface mlag-port-channel

History

3.1.0000


3.3.4500

Added MPO configuration mode

Example

switch (config interface ethernet 1/4) # shutdown

Related Commands

show interfaces ethernet

Notes




speed


speed {<value> [no-autoneg | speed_value [... speed_value]] | <auto>} [force]
no speed

Sets the speed of the interface.
The no form of the command sets the speed of the interface to its default value.

Syntax Description

value

The following speeds are available:

  • 1G or 1000 - 1GbE
  • 10G or 10000 - 10GbE
  • 25G or 25000 - 25GbE
  • 40G or 40000 - 40GbE
  • 50G or 50000 - 50GbE
  • 56G or 56000 - 56GbE
  • 100G or 100000 - 100GbE
  • auto - auto negotiates link speed (not supported on MPO or LAG interfaces)

no-autoneg

Disallows speed auto-negotiation on the interface

force

Forces speed change configuration

Default

Depends on the port module type (see the “Notes” section below)

Configuration Mode

config interface ethernet
config interface port-channel

config interface mlag-port-channel

History

3.1.0000


3.5.0000

Added 25GbE, 50GbE, and 100GbE speeds and updated notes

3.6.6000

Added the no-autoneg parameter

Example

switch (config interface ethernet 1/1) # speed 40G
Related Commandsshow interfaces ethernet

Notes

  • The default speed of an interface depends on its speed capabilities, an interface capable of 100GbE will have 100GbE speed by default

  • It is not possible to set the speed on a LAG or MPO interface
  • Not all interfaces support all speed options
  • It is not possible to set “auto” speed with the “no-autoneg” parameter
  • It is not possible to set “auto” speed along with specific speeds
  • A port with more than one speed advertised or a port configured to “auto” speed cannot be added to LAG
  • To change the speed of a LAG interface:
    1. Remove Ethernet ports from LAG.
    2. Shutdown ports.
    3. Reconfigure port speed.
    4. Re-enable ports.
    5. Re-add ports to LAG interface.



clear counters


clear counters

Clears the interface counters.

Syntax Description

N/A

Default

N/A

Configuration Mode

config interface ethernet
config interface port-channel
config interface mlag-port-channel

History

3.1.0000


3.3.4500

Added MPO configuration mode

Example

switch (config interface ethernet 1/1) # clear counters
Related Commandsshow interfaces ethernet

Notes

This command also clears NVE counters



show interfaces counters


show interfaces <type> <id> counters [priority <prio>]

Displays the extended counters for the interface.

Syntax Description

id

Interface number: <slot>/<port>

priority

Displays interface extended counters per priority. Range: 0-7 or “all”

Default

N/A

Configuration Mode

Any command mode

History

3.1.0000


3.6.1002

Added “error packets” counter to Tx

3.6.4006

Added extended output for storm-control

3.6.5000

Added hoq discard packets counter

Example

switch (config) # show interfaces ethernet 1/1 counters

Rx
  0                    packets
  0                    unicast packets
  0                    multicast packets
  0                    broadcast packets
  0                    bytes
  0                    packets of 64 bytes
  0                    packets of 65-127 bytes
  0                    packets of 128-255 bytes
  0                    packets of 256-511 bytes
  0                    packets of 512-1023 bytes
  0                    packets of 1024-1518 bytes
  0                    packets Jumbo
  0                    error packets
  0                    discard packets
  0                    hoq discard packets
  0                    fcs errors
  0                    undersize packets
  0                    oversize packets
  0                    pause packets
  0                    unknown control opcode
  0                    symbol errors
(appears only on L2 ethernet ports and port-channels supported interfaces)
..0                    packets
..0                    unicast packets
..0                    multicast packets
..
  0                    error packets
  0                    discard packets
  0                    discard packets by Storm Control
  0                    fcs errors
  0                    undersize packets

Tx
  0                    packets
  0                    unicast packets
  0                    multicast packets
  0                    broadcast packets
  0                    bytes
  0                    error packets
  0                    discard packets
  0                    hoq discard packets
  0                    pause packets
  0                    TX wait
  0                    TX wait useconds
  0                    queue depth TC0
  0                    queue depth TC1
  0                    queue depth TC2
  0                    queue depth TC3
  0                    queue depth TC4
  0                    queue depth TC5
  0                    queue depth TC6
  0                    queue depth TC7

Related Commands


Notes

Mellanox Spectrum® based systems display queue depth for TC0-TC7



show interfaces counters discard


show interfaces <type> <id> counters discard

Displays discarded counters of the interface.

Syntax Description

id

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.6.6102

Example

switch (config) # show interfaces ethernet 1/9 counters discard 

Interface Eth1/9:
  Rx:
    0                     discard packets
    0                     error packets
    0                     fcs errors
    0                     undersize packets
    0                     oversize packets
    0                     unknown control opcode
    0                     symbol errors
    0                     discard packets by storm control
    0                     general discard packets
    0                     policy discard packets
    0                     invalid tag packets
    0                     discard packets by vlan filter

  Tx:
    0                     discard packets
    0                     error packets
    0                     hoq discard packets
    0                     oversize packets
    0                     policy discard packets
    0                     SLL discard packets
    0                     discard packets by vlan filter
    0                     discard packets by stp filter
    0                     discard packets by loopback filter

Related Commands


Notes




show interfaces ethernet


show interfaces ethernet <inf>

Displays the configuration and status for the interface.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.1.0000


3.6.1002

Added “error packets” counter to Tx, “Last change in operational status”, and “Isolation group” to output

3.6.2002

Added “boot delay” parameters to output

3.6.3640

Added support for “forwarding mode”

3.6.4110

Updated Example with “Forwarding mode”

3.6.5000

Added telemetry to output

3.6.6000

Added output line for “auto-negotiation”

3.6.8008

Updated Example

3.6.8100

Updated Example

3.7.1100

Updated Example and Notes

Example

switch (config) # show interfaces ethernet 1/10
Eth1/10:
  Admin state                      : Enabled
  Operational state                : Up
  Last change in operational status: 0:00:47 ago (1 oper change)
  Boot delay time                  : 0 sec
  Description                      : N\A
  Mac address                      : 7c:fe:90:f5:8d:2e
  MTU                              : 1500 bytes (Maximum packet size 1522 bytes)
  Fec                              : auto
  Operational Fec                  : rs-fec
  Flow-control                     : receive off send off
  Supported speeds                 : 1G 10G 25G 40G 50G 56G 100G
  Advertised speeds                : 100G
  Actual speed                     : 100G
  Auto-negotiation                 : Enabled
  Width reduction mode             : Unknown
  Switchport mode                  : access
  MAC learning mode                : Enabled
  Forwarding mode                  : inherited cut-through
Telemetry sampling: Disabled TCs: N\A Telemetry threshold: Disabled TCs: N\A Telemetry threshold level: N\A Last clearing of "show interface" counters: Never 60 seconds ingress rate : 232 bits/sec, 29 bytes/sec, 1 packets/sec 60 seconds egress rate : 8 bits/sec, 1 bytes/sec, 1 packets/sec Rx: 25 packets 0 unicast packets 25 multicast packets 0 broadcast packets 1600 bytes 0 discard packets 0 error packets 0 fcs errors 0 undersize packets 0 oversize packets 0 pause packets 0 unknown control opcode 0 symbol errors 0 discard packets by storm control Tx: 3 packets 0 unicast packets 3 multicast packets 0 broadcast packets 192 bytes 0 discard packets 0 error packets 0 hoq discard packets

Related Commands


Notes

  • If a high power transceiver (e.g. LR4) is inserted to a port that does not support it, the link does not go up, and the following warning message is displayed: “Warning: High power transceiver is not supported” when running the command “show interfaces ethernet” is run. For more information, please refer to “High Power Transceivers”.
  • “Operational Fec” appears as N/A while port is DOWN, and as no-fec/fc-fec/rs-fec while port is UP



show interfaces ethernet description


show interfaces ethernet [<inf>] description

Displays the admin status and protocol status for the specified interface.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.1.0000


3.4.1100

Updated Example

Example

switch (config) # show interfaces ethernet description

Interface               Admin state         Operational state
---------               -----------         -----------------
Eth1/58                 Enabled             Down
Eth1/59                 Enabled             Up
Eth1/60                 Enabled             Down (Suspend)
switch (config) # show interfaces ethernet 1/60 description

Eth1/60

  Admin state: Enabled
  Operational state: Down (Suspend)
Related Commands

Notes




show interfaces ethernet rates


show interfaces ethernet rates [<transfer-rate-unit>]

Displays the current transfer rate of the interface.

Syntax Description

transfer-rate-unit

  • bytes displays interface transfer rates in B/s dynamically (while converting to K/M/G if needed)
  • KB displays interface transfer rate in Kb/s
  • MB displays interface transfer rate in Mb/s
  • GB displays interface transfer rate in Gb/s
  • bits displays interface transfer rates in b/s dynamically (while converting to K/M/G if needed)
  • Kb displays interface transfer rate in Kb/s
  • Mb displays interface transfer rate in Mb/s
  • Gb displays interface transfer rate in Gb/s
  • If no parameter is entered, transfer rate is displayed in bits

Default

N/A

Configuration Mode

Any command mode

History

3.6.2002


3.7.0000

Added new rates to “transfer-rate-unit”

Example

switch (config) # show interfaces ethernet rates KB

Port                        egress                             ingress
                  avg rate (KB/s)   pkts/sec         avg rate (KB/s)   pkts/sec
---------        ----------------   --------         ---------------   --------
Eth1/1                       0            0                 0.032            1
Eth1/2                       0            0                 0.032            1
Eth1/3                       0            0                     0            0
...
Related Commands

Notes




show interfaces ethernet status


show interfaces ethernet [<inf>] status

Displays the status, speed and negotiation mode of the specified interface.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.1.0000


3.4.1100

Updated Example

Example

switch (config) # show interfaces ethernet status

Port                   Operational state           Speed                  Negotiation
----                   -----------------           -----                  -----------
Eth1/58                Down                        40 Gbps             No-Negotiation
Eth1/59                Up                          40 Gbps             No-Negotiation
Eth1/60                Down (Suspend)              40 Gbps             No-Negotiation
Related Commands

Notes




show interfaces ethernet transceiver


show interfaces ethernet [<inf>] transceiver

Displays transceiver information.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.1.0000

Example

switch (config) # show interfaces ethernet status

Port                   Operational state           Speed                  Negotiation
----                   -----------------           -----                  -----------
Eth1/58                Down                        40 Gbps             No-Negotiation
Eth1/59                Up                          40 Gbps             No-Negotiation
Eth1/60                Down (Suspend)              40 Gbps             No-Negotiation
Related Commands
switch (config) # show interfaces ethernet 1/1 transceiver
Port 1/1 state
        identifier             : QSFP+
        cable/module type      : Optical cable/module
        ethernet speed and type: 40GBASE - SR4
        vendor                 : Mellanox
        cable_length           : 50 m
        part number            : MC2210411-SR4
        revision               : A1
        serial number          : TT1151-00006

Notes



show interfaces ethernet transceiver brief


show interfaces ethernet [<inf>] transceiver brief

Display brief transceiver information.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.6.6102

Example

switch (config) # show interfaces ethernet 1/1 transceiver brief
show interfaces ethernet transceiver brief 

----------------------------------------------------------------------------------------
Interface       Identifier      Vendor           PN               SN               Rev   
----------------------------------------------------------------------------------------
Eth1/1                                                                              
Eth1/2          QSFP+           Mellanox         MCP1600-E00A     MT1710VS06916    A3
Eth1/3          QSFP+           Mellanox         MCP1600-E00A     MT1710VS06929    A3
Eth1/4          QSFP+           Mellanox         MCP1600-E00A     MT1710VS06953    A3
Eth1/5          QSFP+           Mellanox         MCP1600-E00A     MT1710VS06923    A3
Related Commands

Notes



show interfaces ethernet transceiver counters


show interfaces ethernet [<inf>] transceiver counters

Displays PHY counters.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.6.1002

Example

switch (config) # show interfaces ethernet 1/1 transceiver counters 

Rx
phy received bits               17725862707200
phy symbol errors               0
phy corrected bits              0
Related Commands
Notes
  • The counter “phy received bits” provides information on the total amount of traffic received and can be used to estimate the ratio of error traffic
  • The counter “phy symbol errors” provides information on the error traffic that was not corrected because the FEC algorithm could not do it or because FEC was not active on this interface
  • The counter “phy corrected bits” provides the number of corrected bits by the active FEC mode (RS/FC)



show interfaces ethernet transceiver counters details


show interfaces ethernet [<inf>] transceiver counters

Displays all PHY counters.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.6.1002

Example

switch (config) # show interfaces ethernet 1/1 transceiver counters details

Phy counters
Symbol errors                   0
Sync headers errors             0
Edpl/bip errors lane0           0
Edpl/bip errors lane1           0
Edpl/bip errors lane2           0
Edpl/bip errors lane3           0
FC corrected blocks lane0       0
FC corrected blocks lane1       0
FC corrected blocks lane2       0
FC corrected blocks lane3       0
FC uncorrectable blocks lane0   0
FC uncorrectable blocks lane1   0
FC uncorrectable blocks lane2   0
FC uncorrectable blocks lane3   0
RS corrected blocks             0
RS uncorrectable blocks         0
RS no errors blocks             0
RS single error blocks          0
RS corrected symbols total      0
RS corrected symbols lane0      0
RS corrected symbols lane1      0
RS corrected symbols lane2      0
RS corrected symbols lane3      0
Link down events                0
Successful recovery events      0
Time since last clear           3545366
Related Commands
Notes

The number of lanes displayed depends on interface splitter ratio (4-way-split – each split has only 1 lane; 2-way-split – each split has 2 lanes)



show interfaces ethernet transceiver diagnostics


show interfaces ethernet [<inf>] transceiver diagnostics

Displays cable channel monitoring and diagnostics info for this interface. Tx and Rx power are reported in mW and dBm units.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.6.2002


3.6.4006

Updated Example to report Tx and Rx power in mW and dBm units

3.6.6000

Updated Example

Example

switch (config) # show interfaces ethernet 1/5 transceiver diagnostics

Port 1/5 transceiver diagnostic data:
  Temperature (-127C to +127C):
    Temperature          : 26 C
    Hi Temp Alarm Thresh : 80 C
    Low Temp Alarm Thresh: -10 C
    Temperature Alarm    : None

  Voltage ( 0 to 6.5535 V):
    Voltage              : 3.28980 V
    Hi Volt Alarm Thresh : 3.50000 V
    Low Volt Alarm Thresh: 3.10000 V
    Voltage Alarm        : None

  Tx Bias Current ( 0 to 131 mA):
    Ch1 Tx Current          : 6.60000 mA
    Ch2 Tx Current          : 6.60000 mA
    Ch3 Tx Current          : 6.60000 mA
    Ch4 Tx Current          : 6.60000 mA
    Hi Tx Crnt Alarm Thresh : 8.50000 mA
    Low Tx Crnt Alarm Thresh: 5.49200 mA
    Ch1 Tx Current Alarm    : None
    Ch2 Tx Current Alarm    : None
    Ch3 Tx Current Alarm    : None
    Ch4 Tx Current Alarm    : None

  Tx Power ( 0 mW to 6.5535 mW / 8.1647 dBm):
    Ch1 Tx Power             : 1.01420 mW / 0.06124 dBm
    Ch2 Tx Power             : 0.96740 mW / -0.14394 dBm
    Ch3 Tx Power             : 0.96730 mW / -0.14439 dBm
    Ch4 Tx Power             : 0.96050 mW / -0.17503 dBm
    Hi Tx Power Alarm Thresh : 3.46730 mW / 5.39991 dBm
    Low Tx Power Alarm Thresh: 0.07240 mW / -11.40261 dBm
    Ch1 Tx Power Alarm       : None
    Ch2 Tx Power Alarm       : None
    Ch3 Tx Power Alarm       : None
    Ch4 Tx Power Alarm       : None

  Rx Power ( 0 mW to 6.5535 mW / 8.1647 dBm):
    Ch1 Rx Power             : 0.99160 mW / -0.03663 dBm
    Ch2 Rx Power             : 1.06080 mW / 0.25633 dBm
    Ch3 Rx Power             : 1.09810 mW / 0.40642 dBm
    Ch4 Rx Power             : 0.97500 mW / -0.10995 dBm
    Hi Rx Power Alarm Thresh : 3.46730 mW / 5.39991 dBm
    Low Rx Power Alarm Thresh: 0.04670 mW / -13.30683 dBm
    Ch1 Rx Power Alarm       : None
    Ch2 Rx Power Alarm       : None
    Ch3 Rx Power Alarm       : None
    Ch4 Rx Power Alarm       : None

  Vendor Date Code (dd-mm-yyyy): 07-11-2016
Related Commands

Notes

This example is for a QSFP transceiver



show interfaces ethernet transceiver raw


show interfaces ethernet [<inf>] transceiver raw

Displays cable info for this interface.

Syntax Description

inf

Interface number: <slot>/<port>

Default

N/A

Configuration Mode

Any command mode

History

3.6.1002

Example
switch (config) # show interfaces ethernet 1/7 transceiver raw
Port 1/7 raw transceiver data:

I2C Address 0x50, Page 0, 0:255:
  0000  0d 02 06 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0010  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0020  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0030  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0040  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0050  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0060  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0070  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0080  0d 00 23 08 00 00 00 00 00 00 00 05 8d 00 00 00  ..#.............
  0090  00 00 01 a0 4d 65 6c 6c 61 6e 6f 78 20 20 20 20  ....Mellanox
  00a0  20 20 20 20 0f 00 02 c9 4d 43 32 32 30 37 31 33      ....MC220713
  00b0  30 2d 30 30 41 20 20 20 41 33 02 03 05 00 46 66  0-00A   A3....Ff
  00c0  00 00 00 00 4d 54 31 32 32 37 56 53 30 30 36 34  ....MT1227VS0064
  00d0  32 20 20 20 31 32 30 37 30 38 20 20 00 00 00 e4  2   120708  ....
  00e0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00f0  00 00 00 00 00 00 00 00 00 00 02 00 00 30 00 00
I2C Address 0x50, Pages 1, 128:255:
  0080  0d 02 06 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  0090  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00a0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00b0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00c0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00d0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00e0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  00f0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Related Commands

Notes







show interfaces status


show interfaces status 

Displays the configuration and status for the interface.

Syntax Description

N/A

Default

N/A

Configuration Mode

Any command mode

History

3.6.4006

Example

switch (config) # show interfaces status

--------------------------------------------------------------------------------------------------------------------------------
Port                Operational state   Admin                         Speed           Description
--------------------------------------------------------------------------------------------------------------------------------
mgmt0               Up                  Enabled                       1000Mb/s (auto) -
Eth1/1              Down                Disabled                      Unknown         -
Eth1/2              Up                  Enabled                       40G             -
Eth1/3              Up                  Enabled                       40G             -
Eth1/4              Up                  Enabled                       40G             -
Eth1/5              Up                  Enabled                       40G             -
Eth1/6              Down                Disabled                      Unknown         -
Eth1/7              Down                Disabled                      Unknown         -
Eth1/8              Down                Disabled                      Unknown         -
Eth1/9              Down                Disabled                      Unknown         -
Eth1/10             Up                  Enabled                       100G            -
Eth1/11             Up                  Enabled                       100G            -
Eth1/12             Up                  Enabled                       100G            -
Eth1/13             Up                  Enabled                       100G            -
Eth1/14             Down                Disabled                      Unknown         -
Eth1/15             Up                  Enabled                       100G            -
Eth1/16	            Up                  Enabled                       100G            -

Related Commands


Note

If a high power transceiver (e.g. LR4) is inserted to a port that does not support it, the link does not go up, and the following warning message is displayed: “Warning: High power transceiver is not supported” when running the command “show interfaces ethernet” is run. For more information, please refer to “High Power Transceivers”.