Software Management

This chapter displays all the relevant commands used to manage the system software image.

image boot

	image boot {location <location-id> \| next} Specifies the default location where the system should be booted from.
Syntax Description	location-id	Specifies the default destination location. There can be up to 2 images on the system. Possible values: 1-2.
	next	Sets the boot location to be the next once after the one currently booted from, thus avoiding a cycle through all the available locations
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # image boot location 2
Related Commands	show images
Notes

boot next

	boot next fallback-reboot enable no boot next fallback-reboot enable Sets the default setting for next boot. Normally, if the system fails to apply the configuration on startup (after attempting upgrades or downgrades, as appropriate), it will reboot to the other partition as a fallback. The no form of the command tells the system not to do that, only for the next boot.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # boot fallback-reboot enable
Related Commands	show images
Notes	Normally, if the system fails to apply the configuration on startup (after attempting upgrades or downgrades, as appropriate), it will reboot to the other partition as a fallback. The 'no' variant of this command tells the system NOT to do that, ONLY for the next boot. Note that this setting is not persistent, and will go back to enabled automatically after every boot.

image delete

	image delete <image-name> Deletes the specified image file.
Syntax Description	image-name	Specifies the image name
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # image delete image-ufm_appliance-x86_64-x86_64-20121205-152024.img
Related Commands	show images
Notes

image fetch

	image fetch <URL> [<filename>] Downloads an image from the specified URL or via SCP.
Syntax Description	URL	HTTP, HTTPS, FTP, TFTP, SCP and SFTP are supported Example: scp://username[:password]@hostname/path/filename
	filename	Specifies a filename for this image to be stored as locally
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # image fetch scp://<username>@192.168.10.125/var/www/html/<image_name> Password ****** 100.0%[###########################################################################################]
Related Commands	show images
Notes	Please delete the previously available image, prior to fetching the new image See section "Updating UFM™ SDN Appliance Software” in the Mellanox UFM SDN Appliance User Manual for a full upgrade example

image install

	image install <image-filename> [location <location-id>] \| [progress <prog-options>] [verify <ver-options>] Downloads an image from the specified URL or via SCP.
Syntax Description	image filename	Specifies the image name
	location-id	Specifies the image destination location
	prog-options	“no-track” overrides CLI default and does not track the installation progress. “track” overrides CLI default and tracks the installation progress.
	ver-options	“check-sig” requires an image to have either a valid signature or no signature. “ignore-sig” allows unsigned or invalidly signed images to be installed. “require-sig” requires from the installed image to have a valid signature. If a valid signature is not found on the image, the image cannot be installed.
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # image install image-ufm_appliance-x86_64-x86_64-20121205-152024.img Step 1 of 4: Verify Image 100.0% [###############################################################################################] Step 2 of 4: Uncompress Image 100.0% [###############################################################################################] Step 3 of 4: Create Filesystems 100.0% [###############################################################################################] Step 4 of 4: Extract Image 100.0% [###############################################################################################]
Related Commands	show images
Notes	The image cannot be installed on the “active” location (the one which is currently being booted) On a two-location system, the location is chosen automatically if no location is specified

image move

	image move <src image name> <dest image name> Renames the specified image file.
Syntax Description	src image name	Specifies the old image name
	dest image name	Specifies the new image name
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # image move image1.img image2.img
Related Commands	show images
Notes

image option

	image options require-sig no image options require-sig Requires from all the installed images a valid signature. The no form of the command does not require a signature. However if one is present, it must be valid.
Syntax Description	require-sig	Requires images to be signed by a trusted signature
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # image options require-sig
Related Commands	show images
Notes

show bootvar

	show bootvar Displays the installed system images and the boot parameters.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # show bootvar Installed images: Partition 1: ufm_appliance UFMAPL_1.1.0.11_UFM_3.8.2.5 2012-12-05 15:20:24 x86_64 Partition 2: ufm_appliance UFMAPL_1.0.5.0_UFM_3.8.0.16 2012-10-24 14:27:53 x86_64 Last boot partition: 1 Next boot partition: 1 Boot manager password is set. No image install currently in progress. Image signing: trusted signature always required Admin require signed images: yes Settings for next boot only: Fallback reboot on configuration failure: yes (default)
Related Commands	N/A
Notes

show images

	show image Displays information about the system images and boot parameters.
Syntax Description	N/A
Default	N/A
Configuration Mode	Any configuration mode
History	1.5
Example	ufmapl [ mgmt-sa ] (config) # show images Images available to be installed: image-ufm_appliance-x86_64-x86_64-20121205-152024.img ufm_appliance UFMAPL_1.1.0.11_UFM_3.8.2.5 2012-12-05 15:20:24 x86_64 Installed images: Partition 1: ufm_appliance UFMAPL_1.1.0.11_UFM_3.8.2.5 2012-12-05 15:20:24 x86_64 Partition 2: ufm_appliance UFMAPL_1.0.5.0_UFM_3.8.0.16 2012-10-24 14:27:53 x86_64 Last boot partition: 1 Next boot partition: 1 Boot manager password is set. No image install currently in progress. Image signing: trusted signature always required Admin require signed images: yes Settings for next boot only: Fallback reboot on configuration failure: yes (default)
Related Commands	image boot image delete image fetch image install image move image option boot next
Notes

Content

Space Tools

On This Page

image boot

boot next

image delete

image fetch

image install

image move

image option

show bootvar

show images