Create Content



Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Created on Dec 16, 2021

Updated on Mar 16, 2022

On This Page

Introduction

This post describes how to configure a VMware vSphere Distributed Switch (VDS) with NVIDIA ConnectX-6 card and NATIVE VMware ESXi Driver on VMware vSphere Cluster version 7.0.3c, and perform basic initial configuration steps to enable the driver by using ESXi CLI interface.

Info

VMware ESXi, vSphere Cluster and vCenter install and configuration is out of the scope of this post.

Abbreviations and Acronyms

TermDefinitionTermDefinition
VDS NSX-managed Virtual Distributed SwitchVMVirtual Machine

References

VMware vSphere Distributed Switch

VMware vSphere Distributed Switch (VDS) provides a centralized interface from which you can configure, monitor and administer virtual machine access switching for the entire data center. The VDS provides simplified Virtual Machine network configuration, enhanced network monitoring and troubleshooting capabilities.

NVIDIA® Mellanox® ConnectX®-6 Dx

NVIDIA® Mellanox® ConnectX®-6 Dx is a member of the world-class, award-winning ConnectX series of network adapters. ConnectX-6 Dx delivers two ports of 10/25/40/50/100Gb/s or a single-port of 200Gb/s Ethernet connectivity paired with best-in-class hardware capabilities that accelerate and secure cloud and data center workloads.

Hardware and Software Requirements

Procedure

Configure a VDS

To configure a new VDS, use the following steps.

Create a VDS in a vCenter

To create a new VDS:

  1. Launch the vSphere Web Client and connect to a vCenter Server instance.
    Image Modified
  1. On the vSphere Web Client home screen, select the vCenter object from the list on the left.
    Hover over the Distributed Switches from the Inventory Lists area, then click New Distributed Switch (see image below) to launch the New VDS creation wizard.
    Image Modified

  2. Provide a name for the new distributed switch and select the location within the vCenter inventory where you would like to store the new VDS (a data center object or a folder).
    Click 
    NEXT.
    Image Modified

  3. Select the version of the VDS to create. 
    Click NEXT.
    Image Modified

  4. Specify the number of uplink ports as 2, uncheck the Create a default port group box and specify a name for that group.
    Click NEXT.
    Image Modified

  5. Click Finish.
    Image Modified

  6. Set the MTU for the newly created distributed switch.
    Right-click the new distributed switch in the list of objects and select Settings → Edit Settings... from the Actions menu.
    Image Modified
  7. In the SL_W01-DS01 Distributed Switch - Edit Settings dialog box, in the Advanced tab, set:
    MTU to 9000
    Discovery protocol to Link Layer Discovery Protocol
    Operation to Both.
    Click OK.
    Image Modified

Adding Hosts to VDS

To add an ESXi host to an existing VDS:

  1. Launch the vSphere Web Client, and connect to the vCenter Server instance.

  2. Navigate to the list of Hosts in the SL-WL01-cluster and select ESXi host.

  3. Select Configure → Networking → Physical adapters.

  4. Check the network ports that you are going to use. In this case, vmnic4 and vmnic5 are used.
    Image Modified
              
  5. Navigate to the list of distributed switches.

  6. Right-click the new distributed switch in the list of objects and select Add and Manage Hosts from the Actions menu.

  7. Select the Add hosts button and click NEXT.
    Image Modified


  8. From the list of the new hosts, check the boxes with the names of each ESXi host you would like to add to the VDS.
    Click NEXT.
    Image Modified


  9. In the next Manage physical adapters menu click on Adapters on all hosts and configure vmnic4 and vmnic5 (Sample) in an ESXi host as Uplink 1 and Uplink 2 for the VDS.
    Image Modified



  10. In the next Manage VMkernel adapters and Migrate VM networking menus, click NEXT to continue.
    Image Modified

  11. Click FINISH.
    Image Modified

Creating Distributed Port Groups for Storage Traffic

This section lists the steps required to create two Distributed Port Groups with one Active and one Standby uplinks.

  1. Add VMkernel Adapters for Distributed Port Groups by right-clicking on Distributed switch, and select Distributed Port Group>New Distributed Port Group.
    Image Modified

  2. On the New Distributed Port Group dialog box, enter Name as <NSX-VLAN1624-DPGand click NEXT.
    Image Modified

  3. Set the VLAN type as VLAN trunking, check the Customize default policies configuration checkbox, and click NEXT.
    Image Modified

  4. On the Security dialog box, click NEXT.
    Image Modified

  5. On the Traffic shaping dialog box, click NEXT.
    Image Modified

  6. NIC Teaming

    In the Teaming and failover dialog box, set Uplink 1 as the active uplink and Uplink 2 to standby uplink. Click NEXT.

    Image Modified


  7. In the Monitoring dialog box, set NetFlow to Disabled, and click NEXT.
    Image Modified

  8. In the Miscellaneous dialog box, set Block All Ports to No, and click NEXT.
    Image Modified

  9. In the Ready to complete dialog box, review all the changes before you click FINSIH.
    Image Modified

Adding a VMkernel Network for vSAN Port Group 

To add VMkernel adapters for distributed port groups, follow the steps below.

  1. Right click the distributed port group and select Add VMkernel Adapters.
    Image Modified
  2. Click Attached Hosts...
    Image Modified
  3. Select the hosts and click OK.
    Image Modified
  4. Click NEXT in the Select hosts dialog box.
    Image Modified
  5. Select vSAN(sample) in Available services, and click NEXT.
    Image Modified
  6. Enter the Network Settings and Gateway details, and click NEXT.
    Image Modified
  7. Click FINISH.
    Image Modified


Done !

Authors

Include Page
SA:Boris Kovalev
SA:Boris Kovalev

Related Documents

Content by Label
showLabelsfalse
showSpacefalse
sortcreation
cqllabel in ("vmware","ethernet")