Controller Product ConfigurationΒΆ

The prod configurations are the system-characterized values of the interface and controller settings, which allow an interface to work reliably for a platform. The prod configurations are set separately at the controller and pinmux/pad levels. This file contains the controller-level prod settings.

The DTS configuration file is in the following format:

  deviceprod {
             <controller-name>-<Instance> = <&Label>;
             #prod-cells = <N>;
         <Label>: <controller-name>@<base-address> {
             <mode> {
                     prod = <<address offset> <mask> <value>>;



  • Instance is controller instance id.

  • Label is the label assigned to the node which can be referenced for mapping instance to a node.

  • <controller-name> is predefined module name (sdmmc, qspi, se, i2c).

  • <base-address> is base address of the controller.

  • <mode> is controller mode for which the prod setting needs to be applied (e.g. default, hs400, and so on).

  • <address offset> is the register address offset from base address of the controller/instance

  • <mask> is the mask value (4 bytes, unsigned).

  • <value> is the data value (4 bytes, unsigned).

  • N specifies how many entries are there on the prod setting tuples per configurations.

    • if #prod-cells equals 3, there are three entries per prod configuration, which are address _offset, mask, and value.

The legacy config format used the device instance <controller-name>.<instance-index> instead of the base address of the device. The legacy format keeps one byte to store the instance but the new DTS format will have base address that requires four bytes in the BCT. As a result, some of the fields in the BCT structure have to be shifted accordingly.

For each entry in the prod configuration file, MB1 reads data from the specified address, modifies the data based on mask and value, and then writes the data back to the address:

val = read(address)
val = (val & ~mask) | (value & mask);
write(val, address);

The common prod configuration file is in the hardware/nvidia/platform/t23x/<platform>/bct/ directory.

Here is the new DTS example of a prod configuration file:

 / {
         deviceprod {
                 qspi-0 = <&qspi0>;
                 qspi-1 = <&qspi1>;
                 sdmmc-3 = <&sdmmc3>;

                 #prod-cells = <0x3>;

                 qspi0: qspi@3270000 {
                         default  {
                                 prod = <0x00000004 0x7C00 0x0>,
                                            <0x00000004 0xFF 0x10>;
                 qspi1: qspi@3300000 {
                         default {
                                 prod = <0x00000004 0x7C00 0x0>,
                                            <0x00000004 0xFF 0x10>;
                 sdmmc3: sdmmc@3460000 {
                         default {
                                 prod = <0x000001e4 0x00003FFF 0x0>;
                         hs400 {
                                 prod = <0x00000100 0x1FFF0000 0x14080000>,
                                            <0x0000010c 0x00003F00 0x00000028>;
                         ddr52 {
                                 prod = <0x00000100 0x1FFF0000 0x14080000>;

Here is the previous CFG format:

deviceprod.qspi.0.default.0x03270004.0x7C00 = 0x0 //TX Trimmer
deviceprod.qspi.0.default.0x03270004.0xFF = 0x10 //RX Trimmer

deviceprod.qspi.1.default.0x03300004.0x7C00 = 0x0 //TX Trimmer
deviceprod.qspi.1.default.0x03300004.0xFF = 0x10 //RX Trimmer

deviceprod.sdmmc.3.default.0x034601e4.0x00003FFF = 0x0 // auto cal pd and pu offsets
deviceprod.sdmmc.3.hs400.0x03460100.0x1FFF0000 = 0x14080000 // tap and trim values
deviceprod.sdmmc.3.hs400.0x0346010c.0x00003F00 = 0x00000028 // DQS trim val
deviceprod.sdmmc.3.ddr52.0x03460100.0x1FFF0000 = 0x14080000 // tap and trim values