Accelerated GStreamer

This topic is a guide to the GStreamer version 1.0 and 1.14 based accelerated solution included in NVIDIA® Jetson™ Linux.

Note

References to GStreamer version 1.0 also apply to GStreamer version 1.16.

GStreamer-1.0 Installation and Setup

This section explains how to install and configure GStreamer.

To install GStreamer-1.0

  • Enter the commands:

    $ sudo apt-get update
    $ sudo apt-get install gstreamer1.0-tools gstreamer1.0-alsa \
         gstreamer1.0-plugins-base gstreamer1.0-plugins-good \
         gstreamer1.0-plugins-bad gstreamer1.0-plugins-ugly \
         gstreamer1.0-libav
    $ sudo apt-get install libgstreamer1.0-dev \
         libgstreamer-plugins-base1.0-dev \
         libgstreamer-plugins-good1.0-dev \
         libgstreamer-plugins-bad1.0-dev
    

To check the GStreamer-1.0 version

  • Enter the command:

    $ gst-inspect-1.0 --version
    

GStreamer-1.0 Plugin Reference

Note

The gst-omx plugin is no longer supported in NVIDIA® Tegra® Linux Driver Package (now Jetson Linux) release 34.1. Use the gst-v4l2 plugin for development.

GStreamer version 1.0 includes the following gst-v4l2 video decoders:

Video decoder

Description

nvv4l2decoder

V4L2 H.265 Video decoder

V4L2 H.264 Video decoder

V4L2 VP8 video decoder

V4L2 VP9 video decoder

V4L2 MPEG4 video decoder

V4L2 MPEG2 video decoder

V4L2 AV1 video decoder (supported on NVIDIA® Jetson AGX Orin only)

GStreamer version 1.0 includes the following gst-v4l2 video encoders:

Video encoder

Description

nvv4l2h264enc

V4L2 H.264 video encoder

nvv4l2h265enc

V4L2 H.265 video encoder

nvv4l2vp9enc

V4L2 VP9 video encoder (supported with NVIDIA® Jetson Xavier™ NX series and Jetson AGX Xavier series only)

nvv4l2av1enc

V4L2 AV1 video encoder (supported with NVIDIA® Jetson AGX Orin only)

GStreamer version 1.0 includes the following EGL image video sink:

Video sink

Description

nveglglessink

EGL/GLES video sink element, support both the X11 and Wayland backends

nv3dsink

EGL/GLES video sink element

GStreamer version 1.0 includes the following DRM video sink:

Video sink

Description

nvdrmvideosink

DRM video sink element

GStreamer version 1.0 includes the following proprietary NVIDIA plugins:

NVIDIA proprietary plugin

Description

nvarguscamerasrc

Camera plugin for ARGUS API

nvv4l2camerasrc

Camera plugin for V4L2 API

nvvidconv

Video format conversion and scaling

nvcompositor

Video compositor

nveglstreamsrc

Acts as GStreamer Source Component, accepts EGLStream from EGLStream producer

nvvideosink

Video Sink Component. Accepts YUV-I420 format and produces EGLStream (RGBA)

nvegltransform

Video transform element for NVMM to EGLimage (supported with nveglglessink only)

GStreamer version 1.0 includes the following libjpeg-based JPEG image video encode/decode plugins:

JPEG

Description

nvjpegenc

JPEG encoder element

nvjpegdec

JPEG decoder element

Note

Enter this command before starting the video decode pipeline using gst-launch or nvgstplayer:

$ export DISPLAY=:0

Enter this command to start X server if it is not already running:

$  xinit &

Decode Examples

The examples in this section show how you can perform audio and video decode with GStreamer.

Audio Decode Examples Using gst-launch-1.0

The following examples show how you can perform audio decode using GStreamer-1.0.

  • AAC Decode (OSS Software Decode):

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
       qtdemux name=demux demux.audio_0 ! \
       queue ! avdec_aac ! audioconvert ! alsasink -e
    
  • AMR-WB Decode (OSS Software Decode):

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
         qtdemux name=demux demux.audio_0 ! queue ! avdec_amrwb ! \
         audioconvert ! alsasink -e
    
  • AMR-NB Decode (OSS Software Decode):

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
         qtdemux name=demux demux.audio_0 ! queue ! avdec_amrnb ! \
         audioconvert ! alsasink -e
    
  • MP3 Decode (OSS Software Decode):

    $ gst-launch-1.0 filesrc location=<filename.mp3> ! mpegaudioparse ! \
         avdec_mp3 ! audioconvert ! alsasink -e
    

    Note

    To route audio over HDMI®, set the alsasink property device to the value given for your platform in the table Port to device ID map in the topic Audio Setup and Development.

    For example, use device=hw:0,7 to route audio over the Jetson TX2 HDMI/DP 1 (HDMI) port.

Video Decode Examples Using gst-launch-1.0

The following examples show how you can perform video decode on GStreamer-1.0.

Video Decode Using gst-v4l2

The following examples show how you can perform video decode using the gst-v4l2 plugin on GStreamer-1.0.

  • H.264 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_h264.mp4> ! \
         qtdemux ! queue ! h264parse ! nvv4l2decoder ! nv3dsink -e
    

    Note

    To enable max perf mode, use the enable-max-performance property of the gst-v4l2 decoder plugin. Expect increased power consumption in max perf mode.

    For example:

    $ gst-launch-1.0 filesrc location=<filename_h264.mp4> ! \
         qtdemux ! queue ! h264parse ! nvv4l2decoder \
         enable-max-performance=1 ! nv3dsink -e
    

    Note

    To decode H.264/H.265 GDR streams you must enable error reporting by setting the property enable-frame-type-reporting to true.

    For example:

    $ gst-launch-1.0 filesrc \
         location=<filename_h264.mp4> ! \
         qtdemux ! queue ! h264parse ! nvv4l2decoder \
         enable-frame-type-reporting=1 ! nv3dsink -e
    
  • H.265 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_h265.mp4> ! \
         qtdemux ! queue ! h265parse ! nvv4l2decoder ! nv3dsink -e
    
  • 10-bit H.265 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_10bit.mkv> ! \
         matroskademux ! queue ! h265parse ! nvv4l2decoder ! \
         nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)NV12' ! \
         nv3dsink -e
    
  • 12-bit H.265 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_12bit.mkv> ! \
         matroskademux ! queue ! h265parse ! nvv4l2decoder ! \
         nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)NV12' ! \
         nv3dsink -e
    
  • 8-bit YUV444 (NV24) H.265 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_8bit_YUV444.265> ! \
         h265parse ! nvv4l2decoder ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)NV12' ! \
         nv3dsink -e
    
  • VP9 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_vp9.mkv> ! \
         matroskademux ! queue ! nvv4l2decoder ! nv3dsink -e
    
  • VP8 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_vp8.mkv> ! \
         matroskademux ! queue ! nvv4l2decoder ! nv3dsink -e
    
  • MPEG-4 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_mpeg4.mp4> ! \
         qtdemux ! queue ! mpeg4videoparse ! nvv4l2decoder ! nv3dsink -e
    
  • MPEG-4 Decode DivX 4/5 (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_divx.avi> ! \
         avidemux ! queue ! mpeg4videoparse ! nvv4l2decoder ! nv3dsink -e
    
  • MPEG-2 Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename_mpeg2.ts> ! \
         tsdemux ! queue ! mpegvideoparse ! nvv4l2decoder ! nv3dsink -e
    
  • AV1 Decode (NVIDIA Accelerated Decode):

    $  gst-launch-1.0 filesrc location = <filename_av1.webm> ! \
         matroskademux ! queue ! nvv4l2decoder ! nv3dsink -e
    

Image Decode Examples Using gst-launch-1.0

The following example shows how you can perform JPEG decode on GStreamer-1.0.

  • JPEG Decode (NVIDIA Accelerated Decode):

    $ gst-launch-1.0 filesrc location=<filename.jpg> ! nvjpegdec ! \
         imagefreeze ! xvimagesink -e
    

Encode Examples

The examples in this section show how you can perform audio and video encode with GStreamer.

Audio Encode Examples Using gst-launch-1.0

The following examples show how you can perform audio encode on GStreamer-1.0.

  • AAC Encode (OSS Software Encode):

    $ gst-launch-1.0 audiotestsrc ! \
         'audio/x-raw, format=(string)S16LE,
         layout=(string)interleaved, rate=(int)44100, channels=(int)2' ! \
         voaacenc ! qtmux ! filesink location=test.mp4 -e
    
  • AMR-WB Encode (OSS Software Encode):

    $ gst-launch-1.0 audiotestsrc ! \
         'audio/x-raw, format=(string)S16LE, layout=(string)interleaved, \
         rate=(int)16000, channels=(int)1' ! voamrwbenc ! qtmux ! \
         filesink location=test.mp4 -e
    

Video Encode Examples Using gst-launch-1.0

The following examples show how you can perform video encode with GStreamer-1.0.

Video Encode Using gst-v4l2

The following examples show how you can perform video encode using gst-v4l2 plugin with GStreamer-1.0.

  • H.264 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2h264enc ! \
         bitrate=8000000 ! h264parse ! qtmux ! filesink \
         location=<filename_h264.mp4> -e
    

    Note

    To enable max perf mode, use the maxperf-enable property of the gst-v4l2 encoder plugin. Expect increased power consumption in max perf mode.

    For example:

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2h264enc \
         maxperf-enable=1 bitrate=8000000 ! h264parse ! qtmux ! filesink \
         location=<filename_h264.mp4> -e
    
  • 8-bit YUV444 (NV24) H.264 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 filesrc location=<filename_nv24_352_288.yuv>! \
      videoparse width=352 height=288 format=52 framerate=30 ! \
      'video/x-raw, format=(string)NV24' ! nvvidconv ! \
      'video/x-raw(memory:NVMM), format=(string)NV24' ! nvv4l2h264enc \
      profile=High444 ! h264parse ! filesink \
      location=<filename_8bit_nv24.264> -e
    

    Note

    8-bit YUV444 H.264 encode is supported with High444 profile.

  • H.265 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2h265enc \
         bitrate=8000000 ! h265parse ! qtmux ! filesink \
         location=<filename_h265.mp4> -e
    

    Note

    Jetson AGX Xavier and Jetson AGX Orin can support 8Kp30 H.265 encode. For example:

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)3840, \
         height=(int)2160, format=(string)NV12, \
         framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), width=(int)7860, \
         height=(int)4320, format=(string)NV12 ! nvv4l2h265enc \
         preset-level=1 control-rate=1 bitrate=40000000 ! \
         h265parse ! matroskamux ! \
         filesink location=<filename_8k_h265.mkv> -e
    
  • 10-bit H.265 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)P010_10LE' ! \
         nvv4l2h265enc bitrate=8000000 ! h265parse ! qtmux ! \
         filesink location=<filename_10bit_h265.mp4> -e
    
  • 8-bit YUV444 (NV24) H.265 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 filesrc location=<filename_nv24_352_288.yuv> ! \
      videoparse width=352 height=288 format=52 framerate=30 ! \
      'video/x-raw, format=(string)NV24' ! nvvidconv ! \
      'video/x-raw(memory:NVMM), format=(string)NV24' ! nvv4l2h265enc \
      profile=Main ! h265parse ! filesink location=<filename_8bit_nv24.265> -e
    

    Note

    8-bit YUV444 H.265 encode is supported with Main profile.

  • VP9 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2vp9enc \
         bitrate=8000000 ! matroskamux ! filesink \
         location=<filename_vp9.mkv> -e
    

    Note

    Jetson AGX Orin does not support VP9 encode using gst-v4l2.

  • VP9 Encode with IVF Headers (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2vp9enc \
         enable-headers=1 bitrate=8000000 ! filesink \
         location=<filename_vp9.vp9> -e
    
  • AV1 Encode (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2av1enc \
         bitrate=20000000 ! webmmux ! filesink \
         location=<filename_av1.webm> -e
    

    Note

    AV1 encode using gst-v4l2 is supported only Jetson Orin.

  • AV1 Encode with IVF Headers (NVIDIA Accelerated Encode):

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvv4l2av1enc \
         enable-headers=1 bitrate=8000000 ! filesink \
         location=<filename_av1.av1> -e
    

Image Encode Examples Using gst-launch-1.0

The following example shows how you can perform JPEG encode on GStreamer-1.0.

  • Image Encode:

    $ gst-launch-1.0 videotestsrc num-buffers=1 ! \
         'video/x-raw, width=(int)640, height=(int)480, \
         format=(string)I420' ! nvjpegenc ! filesink location=test.jpg -e
    

Supported H.264/H.265/VP9/AV1 Encoder Features with GStreamer-1.0

This section describes example gst-launch-1.0 usage for features supported by the NVIDIA accelerated H.264/H.265/VP9/AV1 encoders.

Features Supported Using gst-v4l2

This section describes example gst-launch-1.0 usage for features supported by the NVIDIA accelerated H.264/H.265/VP8/VP9 gst-v4l2 encoders.

Note

Display detailed information on the nvv4l2h264enc, nvv4l2h265enc, v4l2vp9enc, or nvv4l2vp8enc encoder property with the command:

$ gst-inspect-1.0 [nvv4l2h264enc | nvv4l2h265enc | nvv4l2vp9enc | nvv4l2av1enc]
  • Set I-frame interval (supported with H.264/H.265/VP9/AV1 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         iframeinterval=100 ! h264parse ! qtmux ! filesink \
         location=<filename_h264.mp4> -e
    

    This property sets encoding Intra Frame occurrence frequency.

  • Set rate control mode and bitrate (supported with H.264/H.265/VP9/AV1 encode):

    The supported modes are 0 (variable bit rate, or VBR) and 1 (constant bit rate, or CBR).

    • Set variable bitrate mode:

      $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         control-rate=0 bitrate=30000000 ! h264parse ! qtmux ! filesink \
         location=<filename_h264_VBR.mp4> -e
      

Note

AV1 codec does not currently support VBR mode.

  • Set constant bitrate mode:

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
       'video/x-raw, width=(int)1280, height=(int)720, \
       format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
       'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
       control-rate=1 bitrate=30000000 ! h264parse ! qtmux ! filesink \
       location=<filename_h264_CBR.mp4> -e
    
  • Set peak bitrate:

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         bitrate=6000000 peak-bitrate=6500000 ! h264parse ! qtmux ! \
         filesink location=<filename_h264.mp4> -e
    

    Peak bitrate takes effect only in variable bit rate mode (control-rate=0). By default, the value is configured as (1.2×bitrate).

  • Set quantization parameter for I, P and B frame (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         ratecontrol-enable=0 quant-i-frames=30 quant-p-frames=30 \
         quant-b-frames=30 num-B-Frames=1 ! filesink \
         location=<filename_h264.264> -e
    

    The range of B frames does not take effect if the number of B frames is 0.

  • Set quantization range for I, P and B Frame (supported with H.264/H.265 encode). The format for the range is:

    "<I_range>:<P_range>:<B_range>"
    

    Where <I_range>, <P_range>, and <B_range> are each expressed in the form <min>,<max>, as in this example:

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         qp-range="24,24:28,28:30,30" num-B-Frames=1 ! 'video/x-h264, \
         stream-format=(string)byte-stream, alignment=(string)au' ! filesink \
         location=<filename_h264.264> -e
    
  • Set hardware preset level (supported with H.264/H.265/VP9/AV1 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         preset-level=4 MeasureEncoderLatency=1 ! 'video/x-h264, \
         stream-format=(string)byte-stream, alignment=(string)au' ! \
         filesink location=<filename_h264.264> -e
    

    The following modes are supported:

    • 0: DisablePreset.

    • 1: UltraFastPreset.

    • 2: FastPreset: Only integer pixel (integer-pel) block motion is estimated. For I/P macroblock mode decisions, only Intra 16×16 cost is compared with intermode costs. Supports Intra 16×16 and Intra 4×4 modes.

    • 3: MediumPreset: Supports up to half pixel (half-pel) block motion estimation. For I/P macroblock mode decisions, only Intra 16×16 cost is compared with intermode costs. Supports Intra 16×16 and Intra 4×4 modes.

    • 4: SlowPreset: Supports up to quarter pixel (Qpel) block motion estimation. For I/P macroblock mode decisions, Intra 4×4 as well as Intra 16×16 cost is compared with intermode costs. Supports Intra 16×16 and Intra 4×4 modes.

Note

AV1 codec currently supports only UltraFastPreset and FastPreset.

  • Set profile (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         profile=0 ! 'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! filesink location=<filename_h264.264> -e
    

    The following profiles are supported for H.264 encode:

    • 0: Baseline profile

    • 2: Main profile

    • 4: High profile

    The following profiles are supported for H.265 encode:

    • 0: Main profile

    • 1: Main10 profile

  • Insert SPS and PPS at IDR (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         insert-sps-pps=1 ! \
         'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! filesink location=<filename_h264.264> -e
    

    If enabled, a sequence parameter set (SPS) and a picture parameter set (PPS) are inserted before each IDR frame in the H.264/H.265 stream.

  • Enable two-pass CBR (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         control-rate=1 bitrate=10000000 EnableTwopassCBR=1 ! \
         'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! filesink location=<filename_h264.264> -e
    

    Two-pass CBR must be enabled along with constant bit rate (control-rate=1).

    Note

    For multi-instance encode with two-pass CBR enabled, enable max perf mode by using the maxperf-enable property of the gst-v4l2 encoder to achieve best performance. Expect increased power consumption in max perf mode.

  • Slice-header-spacing with spacing in terms of macroblocks (Supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         slice-header-spacing=8 bit-packetization=0 ! 'video/x-h264, \
         stream-format=(string)byte-stream, alignment=(string)au' ! \
         filesink location=<filename_h264.264> -e
    

    The bit-packetization=0 parameter configures the network abstraction layer (NAL) packet as macroblock (MB)-based, and slice-header-spacing=8 configures each NAL packet as 8 macroblocks maximum.

  • Slice header spacing with spacing in terms of number of bits (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         slice-header-spacing=1400 bit-packetization=1 ! 'video/x-h264, \
         stream-format=(string)byte-stream, alignment=(string)au' ! \
         filesink location=<filename_h264.264> -e
    

    The parameter bit-packetization=1 configures the network abstraction layer (NAL) packet as size-based, and slice-header-spacing=1400 configures each NAL packet as 1400 bytes maximum.

  • Enable CABAC-entropy-coding (supported with H.264 encode for main or high profile):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         profile=2 cabac-entropy-coding=1 ! 'video/x-h264, \
         stream-format=(string)byte-stream, alignment=(string)au' ! \
         filesink location=<filename_h264.264> -e
    

    The following entropy coding types are supported:

    • 0: CAVLC

    • 1: CABAC

  • Set number of B frames between two reference frames (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
      'video/x-raw, width=(int)1280, height=(int)720, \
      format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
      'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
      num-B-Frames=1 ! 'video/x-h264, stream-format=(string)byte-stream, \
      alignment=(string)au' ! filesink location=<filename_h264.264> -e
    

    This property sets the number of B frames between two reference frames.

    Note

    For multi-instance encode with num-B-Frames=2, enable max perf mode by specifying the maxperf-enable property of the gst-v4l2 encoder for best performance. Expect increased power consumption in max perf mode.

  • Enable motion vector metadata (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         EnableMVBufferMeta=1 ! 'video/x-h264, \
         stream-format=(string)byte-stream, alignment=(string)au' ! \
         filesink location=<filename_h264.264> -e
    
  • Set virtual buffer size:

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         vbv-size=10 ! h264parse ! qtmux ! \
         filesink location=<filename_h264.mp4> -e
    

    If the buffer size of the decoder or network bandwidth is limited, configuring virtual buffer size can cause the video stream generation to correspond to the limitations based on the following formula:

    virtual buffer size = vbv-size × (bitrate/fps)

  • Insert AUD (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         insert-aud=1 ! 'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! filesink location=<filename_h264.264> -e
    

    This property inserts an H.264/H.265 Access Unit Delimiter (AUD).

  • Insert VUI (supported with H.264/H.265 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=(int)1280, height=(int)720, \
         format=(string)I420, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc \
         insert-vui=1 ! 'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! filesink location=<filename_h264.264> -e
    

    This property inserts H.264/H.265 video usability information (VUI) in SPS.

  • Set picture order count (POC) type (supported with H.264 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=1920, height=1080, format=I420' ! nvvidconv ! \
         nvv4l2h264enc \
         poc-type=2 ! h264parse ! filesink location=<filename_h264.264> -e
    

    The following values are supported for the poc-type property:

    • 0: POC explicitly specified in each slice header (the default)

    • 2: Decoding/coding order and display order are the same

  • Set Disable CDF Update (supported with AV1 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=300 ! \
         'video/x-raw, width=1920, height=1080, format=I420' ! nvvidconv ! \
         nvv4l2av1enc \
         disable-cdf=0 enable-headers=1 ! filesink location=<filename_av1.av1> -e
    
  • Set Tile Configuration (supported with AV1 encode):

    • For 1x2 Tile configuration:

      $ gst-launch-1.0 videotestsrc num-buffers=30 ! \
      'video/x-raw, width=1920, height=1080, format=I420' ! nvvidconv ! \
      nvv4l2av1enc \
      tiles="1,0" bitrate=20000000 ! qtmux ! \
      filesink location= <filename_av1.mp4> -e
      
    • For 2x1 Tile configuration:

      $ gst-launch-1.0 videotestsrc num-buffers=30 ! \
      'video/x-raw, width=1920, height=1080, format=I420' ! nvvidconv ! \
      nvv4l2av1enc \
      tiles="0,1" bitrate=20000000 ! qtmux ! \
      filesink location= <filename_av1.mp4> -e
      
    • For 2x2 Tile configuration:

      $ gst-launch-1.0 videotestsrc num-buffers=30 ! \
      'video/x-raw, width=1920, height=1080, format=I420' ! nvvidconv ! \
      nvv4l2av1enc \
      preset-level=1 tiles="1,1" bitrate=20000000 ! qtmux ! \
      filesink location= <filename_av1.mp4> -e
      

    The feature encode frames as super-macroblocks, with Log2(Rows) and Log2(Columns) as the input.

  • Set SSIM RDO (supported with AV1 encode):

    $ gst-launch-1.0 videotestsrc num-buffers=30 ! \
         'video/x-raw, width=1920, height=1080, format=I420' ! nvvidconv ! \
         nvv4l2av1enc \
         enable-srdo=1 ! qtmux ! \
         filesink location= <filename_av1.mp4> -e
    

Camera Capture with GStreamer-1.0

To display nvgstcapture-1.0 usage information, enter the command:

$ nvgstcapture-1.0 --help

Note

The nvgstcapture-1.0 application default only supports ARGUS API using the nvarguscamerasrc plugin. The legacy nvcamerasrc plugin support is deprecated.

For more information, see nvgstcapture-1.0 Reference.

Camera Capture with GStreamer-1.0

Use the following command to capture using nvarguscamerasrc and preview display with nvdrmvideosink:

$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), \
     width=(int)1920, height=(int)1080, format=(string)NV12, \
     framerate=(fraction)30/1' ! nvdrmvideosink -e

Note

The nvarguscamerasrc plugin’s maxperf property is removed, as VIC actmon DFS is implemented to handle VIC frequency scaling as per load enabling clients to get required performance.

Progressive Capture Using nvv4l2camerasrc

To capture and preview display with nv3dsink, enter the command:

$ gst-launch-1.0 nvv4l2camerasrc device=/dev/video3 ! \
     'video/x-raw(memory:NVMM), format=(string)UYVY, \
     width=(int)1920, height=(int)1080, \
     interlace-mode= progressive, \
     framerate=(fraction)30/1' ! nvvidconv ! \
     'video/x-raw(memory:NVMM), format=(string)NV12' ! \
     nv3dsink -e

Note

The nvv4l2camerasrc plugin default currently supports only DMABUF (importer role) streaming I/O mode with V4L2_MEMORY_DMABUF.

The nvv4l2camerasrc plugin is currently verified using the NVIDIA V4L2 driver with a sensor that supports YUV capture in UYVY format.

If you need to use a different type of sensor for capture in other YUV formats, see the topic Sensor Software Driver Programming. In that case nvv4l2camerasrc must also be enhanced for required YUV format support.

The nvgstcapture-1.0 application uses the v4l2src plugin to capture still images and video.

The following table shows USB camera support.

USB camera support

Feature

YUV

Preview display

Image capture (VGA, 640×480)

Video capture (480p, 720p, H.264/H.265/VP8/VP9 encode)

Raw-YUV Capture Using v4l2src

Use the following command to capture raw YUV (I420 format) using v4l2src and preview display with xvimagesink:

$ gst-launch-1.0 v4l2src device="/dev/video0" ! \
     "video/x-raw, width=640, height=480, format=(string)YUY2" ! \
     xvimagesink -e

Camera Capture and Encode Support with OpenCV

The OpenCV sample application opencv_nvgstcam simulates the camera capture pipeline. Similarly, the OpenCV sample application opencv_nvgstenc simulates the video encode pipeline.

Both sample applications are based on GStreamer 1.0. They currently are supported only by OpenCV version 3.3.

  • opencv_nvgstcam: Camera capture and preview.

    To simulate the camera capture pipeline with the opencv_nvgstcam sample application, enter the command:

    $ ./opencv_nvgstcam --help
    

    Note

    Currently, opencv_nvgstcam only supports single-instance CSI capture using the d plugin. You can modify and rebuild the application to support GStreamer pipelines for CSI multi-instance captures and USB camera captures by using the v4l2src plugin. The application uses an OpenCV-based video sink for display.

    For camera CSI capture and preview rendering with OpenCV, enter th3 command:

    $ ./opencv_nvgstcam --width=1920 --height=1080 --fps=30
    
  • opencv_nvgstenc: Camera capture and video encode.

    To simulate the camera capture and video encode pipeline with the opencv_nvgstenc sample application, enter the command:

    $ ./opencv_nvgstenc --help
    

    Note

    Currently, opencv_nvgstenc only supports camera CSI capture using the nvarguscamerasrc plugin and video encode in H.264 format by using the nvv4l2h264enc plugin with an MP4 container file. You can modify and rebuild the application to support GStreamer pipelines for different video encoding formats. The application uses an OpenCV-based video sink for display.

    For camera CSI capture and video encode with OpenCV, enter the command:

    $ ./opencv_nvgstenc --width=1920 --height=1080 --fps=30 --time=60 \
            --filename=test_h264_1080p_30fps.mp4
    

Video Playback with GStreamer-1.0

To display nvgstplayer-1.0 usage information, enter the command:

$ nvgstplayer-1.0 --help

Video can be output to HD displays using the HDMI connector on the Jetson device. The GStreamer-1.0 application currently supports the following video sinks:

For overlay sink (video playback on overlay in full-screen mode), enter the command:

$ gst-launch-1.0 filesrc location=<filename.mp4> ! \
     qtdemux name=demux ! h264parse ! nvv4l2decoder ! nvdrmvideosink -e

Video Playback Examples

The following examples show how you can perform video playback using GStreamer-1.0.

  • nveglglessink (windowed video playback, NVIDIA EGL/GLES videosink using default X11 backend):

    Enter this command to start the GStreamer pipeline using nveglglesink with the default X11 backend:

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
         qtdemux name=demux ! h264parse ! nvv4l2decoder ! nveglglessink -e
    

    The nvgstplayer-1.0 application accepts command line options that specify window position and dimensions for windowed playback:

    $ nvgstplayer-1.0 -i <filename> --window-x=300 --window-y=300 \
         --window-width=500 --window-height=500
    
  • nveglglessink (windowed video playback, NVIDIA EGL/GLES videosink using Wayland backend):

    You can use nveglglsink with the Wayland backend instead of the default X11 backend.

    Ubuntu 20.04 does not support the Wayland display server, which means that there is no UI support to switch Wayland from Xorg. You must start the Wayland server (Weston) by using the target’s shell before performing Weston-based operations.

    To start Weston, complete the following steps before you run the GStreamer pipeline the first time with the Wayland backend. The steps are not required after the initial run.

    Start Weston:

    $ nvstart-weston.sh
    

    To run the GStreamer pipeline with the Wayland backend, run the following command to start the pipeline and use nveglglesink with the Wayland backend:

    $ gst-launch-1.0 filesrc \
            location=<filename.mp4> ! qtdemux name=demux ! h264parse ! \
            nvv4l2decoder ! nveglglessink winsys=wayland
    
  • nvdrmvideosink (video playback using DRM): This sink element uses DRM to render videos on connected displays.

    The display driver must be stopped, and DRM driver must be loaded before using the nvdrmvideosink.

    Stop the display manager:

    $ sudo systemctl stop gdm
    $ sudo loginctl terminate-seat seat0
    

    Load the DRM driver:

    For Jetson Xavier use
    $ sudo modprobe tegra_udrm modeset=1
    
    For Jetson Orin use
    $ sudo modprobe nvidia-drm modeset=1
    

    To start the GStreamer pipeline by using nvdrmvideosink, run the following command:

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
         qtdemux! queue ! h264parse ! nvv4l2decoder ! nvdrmvideosink -e
    

    nvdrmvideosink supports these properties

    • conn_id: Set the connector ID for the display.

    • plane_id: Set the plane ID.

    • set_mode: Set the default mode (resolution) for playback.

    The following command illustrates the use of these properties:

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
         qtdemux! queue ! h264parse ! ! nvv4l2decoder ! nvdrmvideosink \
         conn_id=0 plane_id=1 set_mode=0 -e
    
  • nv3dsink video sink (video playback using 3D graphics API): This video sink element works with NVMM buffers and renders using the 3D graphics rendering API. It performs better than nveglglessink with NVMM buffers.

    This command starts the GStreamer pipeline using nv3dsink:

    $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
         qtdemux ! queue ! h264parse ! nvv4l2decoder ! nv3dsink -e
    

    The sink supports setting a specific window position and dimensions using the properties shown in this example:

    $ nv3dsink window-x=300 window-y=300 window-width=512 window-height=512
    

Video Decode Support with OpenCV

You can simulate a video decode pipeline using the GStreamer-1.0-based OpenCV sample application opencv_nvgstdec.

Note

The sample application currently operates only with OpenCV version 3.3.

To perform video decoding with opencv_nvgstdec, enter the command:

$ ./opencv_nvgstdec --help

Note

Currently, opencv_nvgstdec only supports video decode of H264 format using the nvv4l2decoder plugin. You can modify and rebuild the application to support GStreamer pipelines for video decode of different formats. For display, the application utilizes an OpenCV based video sink component.

To perform video decoding with opencv_nvgstdec, enter the command:

$ ./opencv_nvgstdec --file-path=test_file_h264.mp4

Video Streaming with GStreamer-1.0

This section describes procedures for video streaming with GStreamer 1.0.

To perform video streaming with nvgstplayer-1.0

  • Using nvgstplayer-1.0: Enter the command:

    $ nvgstplayer-1.0 -i rtsp://10.25.20.77:554/RTSP_contents/VIDEO/H264/
         test_file_h264.3gp –stats
    

    The supported formats for video streaming are:

    MPEG4 MPEG4+AAC MPEG4+AAC PLUS MPEG4+eAAC PLUS MPEG4+AMR-NB MPEG4+AMR-WB
    H263 H263+AAC H263+AAC PLUS H263+AMR-NB H263+AMR-WB
    H264 H264+AAC H264+AAC PLUS H264+eAAC PLUS H264+AMR-NB H264+AMR-WB
    AAC AAC PLUS eAAC PLUS AMR-NB AMR-WB
  • Using gst-launch-1.0 pipeline:

    • Streaming and video rendering:

      • Transmitting (from target): CSI camera capture + video encode + RTP streaming using network sink:

        $ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), \
             format=NV12, width=1920, height=1080' ! \
             nvv4l2h264enc insert-sps-pps=true ! h264parse ! \
             rtph264pay pt=96 ! udpsink host=127.0.0.1 port=8001 sync=false -e
        
      • Receiving (on target) : Network Source + video decode + video render:

        $ gst-launch-1.0 udpsrc address=127.0.0.1 port=8001 \
             caps='application/x-rtp, encoding-name=(string)H264, payload=(int)96' ! \
             rtph264depay ! queue ! h264parse ! nvv4l2decoder ! nv3dsink -e
        
    • Streaming and file dump:

      • Transmitting (from target): CSI camera capture + video encode + RTP streaming using network sink:

        $ gst-launch-1.0 nvarguscamerasrc ! \
             'video/x-raw(memory:NVMM), format=NV12, width=1920, height=1080' ! \
             nvv4l2h264enc insert-sps-pps=true ! h264parse ! \
             rtph264pay pt=96 ! udpsink host=127.0.0.1 port=8001 sync=false -e
        
      • Receiving (on target): Network Source + video decode + file dump:

        $ gst-launch-1.0 udpsrc address=127.0.0.1 port=8001 \
             caps='application/x-rtp, encoding-name=(string)H264, payload=(int)96' ! \
             rtph264depay ! queue ! h264parse ! nvv4l2decoder ! nvvidconv ! \
             'video/x-raw, format=(string)I420' ! filesink location=test.yuv -e
        

Video Format Conversion with GStreamer-1.0

The NVIDIA proprietary nvvidconv GStreamer-1.0 plugin allows conversion between OSS (raw) video formats and NVIDIA video formats. The nvvidconv plugin currently supports the format conversions described in this section.

Raw-YUV Input Formats

Currently VIC based nvvidconv on Jetson supports the I420, UYVY, YUY2, YVYU, NV12, NV16, NV24, P010_10LE, GRAY8, BGRx, RGBA, and Y42B RAW-YUV input formats and CUDA based nvvidconv on GPU supports the I420, NV12, P010_10LE, GRAY8, BGRx and RGBA input formats.

Enter the following commands to perform VIC-based conversion on Jetson Linux:

  • Using the gst-v4l2 encoder (with other than the GRAY8 pipeline):

    $ gst-launch-1.0 videotestsrc ! 'video/x-raw, format=(string)UYVY, \
         width=(int)1280, height=(int)720' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! \
         nvv4l2h264enc ! 'video/x-h264, \
         stream-format=(string)byte-stream' ! h264parse ! \
         qtmux ! filesink location=test.mp4 -e
    
  • Using the gst-v4l2 encoder with the GRAY8 pipeline:

    $ gst-launch-1.0 videotestsrc ! 'video/x-raw, format=(string)GRAY8, \
         width=(int)640, height=(int)480, framerate=(fraction)30/1' ! \
         nvvidconv ! 'video/x-raw(memory:NVMM), format=(string)I420' ! \
         nvv4l2h264enc ! 'video/x-h264, \
         stream-format=(string)byte-stream' ! h264parse ! qtmux ! \
         filesink location=test.mp4 -e
    

Enter the following commands to perform CUDA-based conversion on an integrated GPU:

Note

The gst-v4l2 encoder does not support CUDA memory, so the output of the first nvvidconv by using GPU is converted to surface array memory by using VIC.

  • Using the gst-v4l2 encoder (with other than the GRAY8 pipeline):

    $ gst-launch-1.0 videotestsrc ! 'video/x-raw, format=(string)NV12, \
         width=(int)1280, height=(int)720' ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw, \
         format=(string)I420' ! nvvidconv compute-hw=VIC \
         nvbuf-memory-type=nvbuf-mem-surface-array ! 'video/x-raw(memory:NVMM)' ! \
         nvv4l2h264enc ! 'video/x-h264, \
         stream-format=(string)byte-stream' ! h264parse ! \
         qtmux ! filesink location=test.mp4 -e
    
  • Using the gst-v4l2 encoder with the GRAY8 pipeline:

    $ gst-launch-1.0 videotestsrc ! 'video/x-raw, format=(string)GRAY8, \
         width=(int)640, height=(int)480, framerate=(fraction)30/1' ! \
         nvvidconv compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw, format=(string)I420' ! nvvidconv compute-hw=VIC \
         nvbuf-memory-type=nvbuf-mem-surface-array ! 'video/x-raw(memory:NVMM)' ! \
         nvv4l2h264enc ! 'video/x-h264, \
         stream-format=(string)byte-stream' ! h264parse ! qtmux ! \
         filesink location=test.mp4 -e
    

Enter the following command to perform CUDA-based format conversion on a dedicated GPU:

Note

The gst-v4l2 encoder can directly use the CUDA memory on a dedicated GPU.

  • Using the gst-v4l2 encoder:

    $ gst-launch-1.0 filesrc location=input_4k_60p.yuv ! videoparse width=3840 \
         height=2160 format=i420 framerate=60 ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw(memory:NVMM), \
         width=(int)3840, height=(int)2160, format=(string)I420, framerate=60/1' ! \
         nvv4l2h264enc ! 'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! h264parse ! qtmux ! \
         filesink location=test.mp4 -e
    

Note

Format conversion with raw YUV input is CPU-intensive due to the “software to hardware” memory copies involved.

Raw-YUV Output Formats

Currently VIC based nvvidconv on Jetson supports the I420, UYVY, YUY2, YVYU, NV12, NV16, NV24, GRAY8, BGRx, RGBA, and Y42B RAW-YUV output formats and CUDA based nvvidconv on GPU supports the I420, NV12, P010_10LE, I420_10LE, GRAY8, BGRx and RGBA output formats.

Enter the following commands to perform VIC based format conversion on Jetson Linux:

  • Using the gst-v4l2 decoder (with other than the GRAY8 pipeline):

    $ gst-launch-1.0 filesrc location=640x480_30p.mp4 ! qtdemux ! \
         queue ! h264parse ! nvv4l2decoder ! nvvidconv ! \
         'video/x-raw, format=(string)UYVY' ! videoconvert ! xvimagesink -e
    
  • Using the gst-v4l2 decoder with the GRAY8 pipeline:

    $ gst-launch-1.0 filesrc location=720x480_30i_MP.mp4 ! qtdemux ! \
         queue ! h264parse ! nvv4l2decoder ! nvvidconv ! 'video/x-raw, \
         format=(string)GRAY8' ! videoconvert ! xvimagesink -e
    

Enter the following command to perform CUDA-based format conversion on an integrated GPU:

  • Using the gst-v4l2 decoder:

    $ gst-launch-1.0 filesrc location=640x480_30p.mp4 ! qtdemux ! \
         queue ! h264parse ! nvv4l2decoder ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! nv3dsink -e
    

Enter the following command to perform CUDA-based format conversion on a dedicated GPU:

  • Using the gst-v4l2 decoder:

    $ gst-launch-1.0 filesrc location=720x480_30i_MP.mp4 ! qtdemux ! \
         h264parse ! nvv4l2decoder cudadec-memtype=1 ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! nveglglessink -e
    

Note

Format conversion with raw YUV output is CPU-intensive due to the “hardware to software” memory copies involved.

NVIDIA Input and Output Formats

Currently CUDA based nvvidconv on GPU supports the I420, NV12, P010_10LE, GRAY8, BGRx and RGBA input formats and supports the I420, NV12, P010_10LE, I420_10LE, GRAY8, BGRx and RGBA output formats and VIC based nvvidconv on Jetson supports the combinations of NVIDIA input and output formats described in the following table. Any format in the column on the left can be converted to any format in the same row in the column on the right.

NV12
NV24
NV16 NV12
NV24
NV16
I420
I420_12LE
I420_10LE
P010_10LE
I420 I420_10LE
P010_10LE
UYVY
YVYU
BGRx
GRAY8
YUY2
Y42B
RGBA
UYVY
YVYU
BGRx
GRAY8
YUY2
Y42B
RGBA

Enter the following commands to perform VIC-based conversion between NVIDIA formats on Jetson Linux:

  • Using the gst-v4l2 decoder:

    $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
         h264parse ! nvv4l2decoder ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)RGBA' ! nvdrmvideosink -e
    
  • Using the gst-v4l2 encoder:

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nvv4l2h264enc ! \
         h264parse ! qtmux ! filesink location=test.mp4 -e
    
  • Using the gst-v4l2 decoder and nv3dsink with the GRAY8 pipeline:

    $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
         h264parse ! nvv4l2decoder ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)GRAY8' ! nvvidconv ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nv3dsink -e
    

Enter the following commands to perform CUDA-based conversion between NVIDIA formats on an integrated GPU:

  • Using the gst-v4l2 decoder:

    $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
         h264parse ! nvv4l2decoder ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw(memory:NVMM), format=(string)RGBA' ! nv3dsink -e
    

Note

The gst-v4l2 encoder does not support CUDA memory, so the output of the first nvvidconv by using GPU is converted to surface array memory by using VIC.

  • Using the gst-v4l2 encoder:

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=(fraction)30/1' ! \
         nvvidconv compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw, format=(string)I420' ! \
         nvvidconv compute-hw=VIC nvbuf-memory-type=nvbuf-mem-surface-array ! \
         'video/x-raw(memory:NVMM)' ! nvv4l2h264enc ! \
         h264parse ! qtmux ! filesink location=test.mp4 -e
    
  • Using the gst-v4l2 decoder and nv3dsink with the GRAY8 pipeline:

    $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
         h264parse ! nvv4l2decoder ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw(memory:NVMM), format=(string)GRAY8' ! \
         nvvidconv compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw(memory:NVMM), format=(string)I420' ! nv3dsink -e
    

Enter the following commands to perform CUDA-based conversion between NVIDIA formats on a dedicated GPU:

Note

The gst-v4l2 encoder can directly use the CUDA memory on a dedicated GPU.

  • Using the gst-v4l2 encoder:

    $ gst-launch-1.0 filesrc location=input_4k_60p_NV12.yuv ! videoparse width=3840 \
         height=2160 format=23 framerate=60 ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw(memory:NVMM), \
         width=(int)3840, height=(int)2160, format=(string)I420, framerate=60/1' ! \
         nvv4l2h264enc ! 'video/x-h264, stream-format=(string)byte-stream, \
         alignment=(string)au' ! h264parse ! qtmux ! \
         filesink location=test.mp4 -e
    
  • Using the gst-v4l2 decoder:

    $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
         h264parse ! nvv4l2decoder cudadec-memtype=1 ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw(memory:NVMM), \
         width=1280, height=720, format=(string)I420 ! nveglglessink -e
    

Video Scaling with GStreamer-1.0

The NVIDIA proprietary nvvidconv GStreamer-1.0 plugin also allows you to perform video scaling. The nvvidconv plugin currently supports scaling with the format conversions described in this section.

  • Raw-YUV input formats:

    Currently VIC based nvvidconv on Jetson supports the I420, UYVY, YUY2, YVYU, NV12, NV16, NV24, P010_10LE, GRAY8, BGRx, RGBA, and Y42B RAW-YUV input formats for scaling and CUDA based nvvidconv on GPU supports the I420, NV12, P010_10LE, GRAY8, BGRx and RGBA input formats for scaling.

    • Using the gst-v4l2 encoder and perform VIC based scaling on Jetson Linux:

      $ gst-launch-1.0 videotestsrc ! \
           'video/x-raw, format=(string)I420, width=(int)1280, \
           height=(int)720' ! nvvidconv ! \
           'video/x-raw(memory:NVMM), width=(int)640, height=(int)480, \
           format=(string)I420' ! nvv4l2h264enc ! \
           'video/x-h264, stream-format=(string)byte-stream' ! h264parse ! \
           qtmux ! filesink location=test.mp4 -e
      

    Note

    The gst-v4l2 encoder does not support CUDA memory, so the output of the first nvvidconv by using GPU is converted to surface array memory by using VIC.

    • Using the gst-v4l2 encoder and perform CUDA-based scaling on an integrated GPU:

      $ gst-launch-1.0 videotestsrc ! \
           'video/x-raw, format=(string)I420, width=(int)1280, \
           height=(int)720' ! nvvidconv compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! \
           'video/x-raw, width=(int)640, height=(int)480, \
           format=(string)I420' ! nvvidconv compute-hw=VIC \
           nvbuf-memory-type=nvbuf-mem-surface-array ! \
           'video/x-raw(memory:NVMM)' ! nvv4l2h264enc ! \
           'video/x-h264, stream-format=(string)byte-stream' ! h264parse ! \
           qtmux ! filesink location=test.mp4 -e
      

    Note

    The gst-v4l2 encoder can directly use the CUDA memory on a dedicated GPU.

    • Using the gst-v4l2 encoder and perform CUDA-based scaling on a dedicated GPU:

      $ gst-launch-1.0 filesrc location=input_4k_60p.yuv ! videoparse width=3840 \
           height=2160 format=i420 framerate=60 ! nvvidconv compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw(memory:NVMM), \
           width=(int)1920, height=(int)1080, format=(string)I420, framerate=60/1' ! \
           nvv4l2h264enc ! 'video/x-h264, stream-format=(string)byte-stream, \
           alignment=(string)au' ! h264parse ! qtmux ! \
           filesink location=test.mp4 -e
      

Note

Video scaling with raw YUV input is CPU-intensive due to the “software to hardware” memory copies involved.

  • Raw-YUV Output Formats:

    Currently VIC based nvvidconv on Jetson supports the I420, UYVY, YUY2, YVYU, NV12, NV16, NV24, GRAY8, BGRx, RGBA, and Y42B RAW-YUV output formats for scaling and CUDA based nvvidconv on GPU supports the I420, NV12, GRAY8, BGRx, RGBA, and I420_10LE output formats for scaling.

    • Using the gst-v4l2 decoder and perform VIC based scaling on Jetson Linux:

      $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
           queue ! h264parse ! nvv4l2decoder ! nvvidconv ! \
           'video/x-raw, format=(string)I420, width=640, height=480' ! \
           xvimagesink -e
      
    • Using the gst-v4l2 decoder and perform CUDA-based scaling on an integrated GPU:

      $ gst-launch-1.0 filesrc location=1280x720_30p.mp4 ! qtdemux ! \
           queue ! h264parse ! nvv4l2decoder ! nvvidconv compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! \
           'video/x-raw, format=(string)I420, width=640, height=480' ! \
           nv3dsink -e
      
    • Using the gst-v4l2 decoder and perform CUDA-based scaling on a dedicated GPU:

      $ gst-launch-1.0 filesrc location = 1280x720_30p.mp4 ! qtdemux ! \
           h264parse ! nvv4l2decoder cudadec-memtype=1 ! nvvidconv compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw(memory:NVMM), \
           width=640, height=480' ! nveglglessink -e
      

Note

Video scaling with raw YUV output is CPU-intensive due to the “hardware to software” memory copies involved.

Video Cropping with GStreamer-1.0

The NVIDIA proprietary nvvidconv GStreamer-1.0 plugin also allows you to perform video cropping:

  • Using the gst-v4l2 decoder and perform VIC based cropping on Jetson Linux:

    $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! qtdemux ! \
         h264parse ! nvv4l2decoder ! \
         nvvidconv left=400 right=1520 top=200 bottom=880 ! nv3dsink -e
    
  • Using the gst-v4l2 decoder and perform CUDA-based cropping on an integrated GPU:

    $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! qtdemux ! \
         h264parse ! nvv4l2decoder ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device \
         left=400 right=1520 top=200 bottom=880 ! nv3dsink -e
    
  • Using the gst-v4l2 decoder and perform CUDA-based cropping on a dedicated GPU:

    $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! qtdemux ! \
         h264parse ! nvv4l2decoder cudadec-memtype=1 ! nvvidconv compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device \
         left=400 right=1520 top=200 bottom=880 ! nveglglessink -e
    

Video Transcode with GStreamer-1.0

You can perform video transcoding between the following video formats.

  • H.264 decode to VP9 Encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! qtdemux ! \
           h264parse ! nvv4l2decoder ! nvv4l2vp9enc !matroskamux name=mux ! \
           filesink location=<Transcoded_filename.mkv> -e
      
  • H.265 decode to VP9 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! h265parse ! nvv4l2decoder ! \
           nvv4l2vp9enc bitrate=20000000 ! queue ! matroskamux name=mux ! \
           filesink location=<Transcoded_filename.mkv> -e
      
  • VP8 decode to H.264 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mebm> ! \
           matroskademux name=demux demux.video_0 ! queue ! nvv4l2decoder ! \
           nvv4l2h264enc bitrate=20000000 ! h264parse ! queue ! \
           qtmux name=mux ! filesink location=<Transcoded_filename.mp4> -e
      
  • VP9 decode to H.265 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.webm> ! \
           matroskademux name=demux demux.video_0 ! queue ! nvv4l2decoder ! \
           nvv4l2h265enc bitrate=20000000 ! h265parse ! queue ! \
           qtmux name=mux ! filesink location=<Transcoded_filename.mp4> -e
      
  • MPEG-4 decode to VP9 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! mpeg4videoparse ! \
           nvv4l2decoder ! nvv4l2vp9enc bitrate=20000000 ! queue ! \
           matroskamux name=mux ! filesink \
           location=<Transcoded_filename.mkv> -e
      
  • MPEG-4 decode to H.264 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! mpeg4videoparse ! \
           nvv4l2decoder ! nvv4l2h264enc bitrate=20000000 ! h264parse ! \
           queue ! qtmux name=mux ! filesink \
           location=<Transcoded_filename.mp4> -e
      
  • H.264 decode to AV1 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! h264parse ! \
           nvv4l2decoder ! nvv4l2av1enc bitrate=20000000 ! queue ! \
           matroskamux name=mux ! \
           filesink location=<Transcoded_filename.mkv> -e
      
  • H.265 decode to AV1 encode (NVIDIA accelerated decode to NVIDIA accelerated encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! h265parse ! \
           nvv4l2decoder ! nvv4l2av1enc bitrate=20000000 ! queue ! \
           matroskamux name=mux ! \
           filesink location=<Transcoded_filename.mkv> -e
      
  • VP8 decode to MPEG-4 encode (NVIDIA accelerated decode to OSS software encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mkv> ! \
           matroskademux name=demux demux.video_0 ! queue ! nvv4l2decoder ! \
           nvvidconv ! avenc_mpeg4 bitrate=4000000 ! queue ! \
           qtmux name=mux ! filesink location=<Transcoded_filename.mp4> -e
      
  • VP9 decode to MPEG-4 encode (NVIDIA accelerated decode to OSS software encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mkv> ! \
           matroskademux name=demux demux.video_0 ! queue ! nvv4l2decoder ! \
           nvvidconv ! avenc_mpeg4 bitrate=4000000 ! qtmux name=mux ! \
           filesink location=<Transcoded_filename.mp4> -e
      
  • H.264 decode to Theora encode (NVIDIA accelerated decode to OSS software encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! h264parse ! \
           nvv4l2decoder ! nvvidconv ! theoraenc bitrate=4000000 ! \
           oggmux name=mux ! filesink location=<Transcoded_filename.ogg> -e
      
  • H.264 decode to H.263 encode (NVIDIA accelerated decode to OSS software encode):

    • Using the gst-v4l2 pipeline:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux demux.video_0 ! queue ! h264parse ! \
           nvv4l2decoder ! nvvidconv ! \
         '  video/x-raw, width=(int)704, height=(int)576, \
         for  mat=(string)I420' ! avenc_h263 bitrate=4000000 ! qtmux ! \
         files  ink location=<Transcoded_filename.mp4> -e
      

CUDA Video Post-Processing with GStreamer-1.0

This section describes GStreamer-1.0 plugins for NVIDIA® CUDA® post-processing operations.

gst-nvivafilter

This NVIDIA proprietary GStreamer-1.0 plugin performs pre/post and CUDA post-processing operations on CSI camera captured or decoded frames, and renders video using overlay video sink or video encode. .. note:: The gst-nvivafilter pipeline requires unsetting the DISPLAY environment variable using the command unset DISPLAY if lightdm is stopped.

  • Sample decode pipeline:

    • Using the gst-v4l2 decoder:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! qtdemux ! queue ! \
           h264parse ! nvv4l2decoder ! nvivafilter cuda-process=true \
           customer-lib-name="libnvsample_cudaprocess.so" ! \
           'video/x-raw(memory:NVMM), format=(string)NV12' ! \
           nvdrmvideosink -e
      
  • Sample CSI camera pipeline:

    $ gst-launch-1.0 nvarguscamerasrc ! \
         'video/x-raw(memory:NVMM), width=(int)3840, height=(int)2160, \
         format=(string)NV12, framerate=(fraction)30/1' ! \
         nvivafilter cuda-process=true \
         customer-lib-name="libnvsample_cudaprocess.so" ! \
         'video/x-raw(memory:NVMM), format=(string)NV12' ! nv3dsink -e
    

Note

See nvsample_cudaprocess_src.tbz2 for the libnvsample_cudaprocess.so library sources. The sample CUDA implementation of libnvsample_cudaprocess.so can be replaced by a custom CUDA implementation.

Video Rotation with GStreamer-1.0

The NVIDIA proprietary nvvidconv GStreamer-1.0 plugin also allows you to perform video rotation operations.

The following table shows the supported values for the nvvidconv flip-method property.

Flip method

flip-method property value

Identity (no rotation. default)

0

Counterclockwise 90 degrees

1

Rotate 180 degrees

2

Clockwise 90 degrees

3

Horizontal flip

4

Upper right diagonal flip

5

Vertical flip

6

Upper left diagonal flip

7

Note

To get information on the nvvidconv flip-method property, enter the command:

$ gst-inspect-1.0 nvvidconv
  • To rotate the video 90 degrees counterclockwise:

    • With gst-v4l2 decoder and perform VIC based rotation on Jetson Linux:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux name=demux ! h264parse ! nvv4l2decoder ! \
           nvvidconv flip-method=1 ! \
           'video/x-raw(memory:NVMM), format=(string)I420' ! \
           nvdrmvideosink -e
      
    • With gst-v4l2 decoder and perform CUDA-based rotation on an integrated GPU:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux ! h264parse ! nvv4l2decoder ! \
           nvvidconv compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device \
           flip-method=1 ! 'video/x-raw(memory:NVMM), format=(string)I420' ! \
           nv3dsink -e
      
    • With gst-v4l2 decoder and perform CUDA-based rotation on a dedicated GPU:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux ! h264parse ! nvv4l2decoder cudadec-memtype=1 ! \
           nvvidconv compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device \
           flip-method=1 ! 'video/x-raw(memory:NVMM)' ! \
           nveglglessink -e
      
  • To rotate the video 90 degrees clockwise:

    • With gst-v4l2 decoder and perform VIC based rotation on Jetson Linux:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux ! h264parse ! nvv4l2decoder ! \
           nvvidconv flip-method=3 ! \
           'video/x-raw(memory:NVMM), format=(string)I420' ! \
           nvdrmvideosink -e
      
    • With gst-v4l2 decoder and perform CUDA-based rotation on an integrated GPU:

      $ gst-launch-1.0 filesrc location=<filename.mp4> ! \
           qtdemux ! h264parse ! nvv4l2decoder ! \
           nvvidconv flip-method=3 compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! \
           'video/x-raw(memory:NVMM), format=(string)I420' ! \
           nv3dsink -e
      
  • To rotate 180 degrees:

    • With nvarguscamerasrc and perform VIC based rotation on Jetson Linux:

      $ gst-launch-1.0 nvarguscamerasrc ! \
           'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
           format=(string)NV12, framerate=(fraction)30/1' ! \
           nvvidconv flip-method=2 ! \
           'video/x-raw(memory:NVMM), format=(string)I420' ! nv3dsink -e
      
    • With nvarguscamerasrc and perform CUDA-based rotation on an integrated GPU:

      $ gst-launch-1.0 nvarguscamerasrc ! \
           'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
           format=(string)NV12, framerate=(fraction)30/1' ! \
           nvvidconv flip-method=2 compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! \
           'video/x-raw(memory:NVMM), format=(string)I420' ! nv3dsink -e
      
  • To scale and rotate the video 90 degrees counterclockwise:

    • Using the gst-v4l2 decoder and perform VIC based rotation on Jetson Linux:

      $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! qtdemux ! \
           h264parse ! nvv4l2decoder ! nvvidconv flip-method=1 ! \
           'video/x-raw(memory:NVMM), width=(int)480, height=(int)640, \
           format=(string)I420' ! nvdrmvideosink -e
      
    • Using the gst-v4l2 decoder and perform CUDA-based rotation on an integrated GPU:

      $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! qtdemux ! \
           h264parse ! nvv4l2decoder ! nvvidconv flip-method=1 \
           compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device ! \
           'video/x-raw(memory:NVMM), width=(int)480, height=(int)640, \
           format=(string)I420' ! nv3dsink -e
      
  • To scale and rotate the video 90 degrees clockwise:

    • With nvarguscamerasrc and perform VIC based rotation on Jetson Linux:

      $ gst-launch-1.0 nvarguscamerasrc ! \
           'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
           format=(string)NV12, framerate=(fraction)30/1' ! \
           nvvidconv flip-method=3 ! 'video/x-raw(memory:NVMM), \
           width=(int)480, height=(int)640, format=(string)I420' ! \
           nv3dsink -e
      
    • With nvarguscamerasrc and perform CUDA-based rotation on an integrated GPU:

      $ gst-launch-1.0 nvarguscamerasrc ! \
           'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
           format=(string)NV12, framerate=(fraction)30/1' ! \
           nvvidconv flip-method=3 compute-hw=GPU \
           nvbuf-memory-type=nvbuf-mem-cuda-device ! 'video/x-raw(memory:NVMM), \
           width=(int)480, height=(int)640, format=(string)I420' ! \
           nv3dsink -e
      
  • To scale and rotate the video 180 degrees:

    • Using the gst-v4l2 decoder and perform VIC based rotation on Jetson Linux:

      $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! \
           qtdemux ! h264parse ! nvv4l2decoder ! nvvidconv flip-method=2 ! \
           'video/x-raw(memory:NVMM), width=(int)640, height=(int)480, \
           format=(string)I420' ! nvdrmvideosink -e
      
    • Using the gst-v4l2 decoder and perform CUDA-based rotation on an integrated GPU:

      $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! \
           qtdemux ! h264parse ! nvv4l2decoder ! nvvidconv flip-method=2 \
           compute-hw=GPU nvbuf-memory-type=nvbuf-mem-cuda-device ! \
           'video/x-raw(memory:NVMM), width=(int)640, height=(int)480, \
           format=(string)I420' ! nv3dsink -e
      

Video Composition with GStreamer-1.0

With the NVIDIA proprietary nvcompositor GStreamer-1.0 plugin, you can perform video composition operations on camera and gst-v4l2 video decoded streams.

To composite decoded streams with different formats

  • Using the gst-v4l2 decoder:

    $ gst-launch-1.0 nvcompositor \
         name=comp sink_0::xpos=0 sink_0::ypos=0 sink_0::width=1920 \
         sink_0::height=1080 sink_1::xpos=0 sink_1::ypos=0 \
         sink_1::width=1600 sink_1::height=1024 sink_2::xpos=0 \
         sink_2::ypos=0 sink_2::width=1366 sink_2::height=768 \
         sink_3::xpos=0 sink_3::ypos=0 sink_3::width=1024 \
         sink_3::height=576 ! 'video/x-raw(memory:NVMM)' ! nv3dsink \
         filesrc location=<filename_h264_1080p_30fps.mp4> ! qtdemux ! \
         h264parse ! nvv4l2decoder ! comp. filesrc \
         location=<filename_h265_1080p_30fps.mp4> ! qtdemux ! h265parse ! \
         nvv4l2decoder ! comp. filesrc \
         location=<filename_av1_1080p_30fps.webm> ! matroskademux ! \
         nvv4l2decoder ! comp. filesrc \
         location=<filename_vp9_1080p_30fps.webm> ! \
         matroskademux  ! nvv4l2decoder ! comp. -e
    

To composite different camera feeds

  • Using the nvarguscamerasrc:

    $ gst-launch-1.0 nvcompositor \
         name=comp sink_0::xpos=960 sink_0::ypos=540 sink_0::width=960 \
         sink_0::height=540 sink_1::width=1920 sink_1::height=1080 ! \
         'video/x-raw(memory:NVMM)' ! queue ! nv3dsink \
         nvarguscamerasrc sensor-id=0 ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=30/1' ! comp. \
         nvarguscamerasrc sensor-id=1 ! \
         'video/x-raw(memory:NVMM), width=(int)1920, height=(int)1080, \
         format=(string)NV12, framerate=30/1' ! comp. -e
    

Interpolation Methods for Video Scaling

The NVIDIA proprietary nvvidconv GStreamer-1.0 plugin allows you to choose the interpolation method used for scaling.

The following table shows the supported values for the VIC based nvvidconv interpolation-method property on Jetson.

Interpolation method

interpolation-method property value

Nearest (default)

0

Bilinear

1

5-tap

2

10-tap

3

Smart

4

Nicest

5

The following table shows the supported values for the CUDA based nvvidconv interpolation-method property on GPU.

Interpolation method

interpolation-method property value

Nearest (default)

0

Bilinear

1

Cubic

2

Super

3

Lanczos

4

Note

To display information about the nvvidconv interpolation-method property, enter the command:

$ gst-inspect-1.0 nvvidconv

To use bilinear interpolation method for scaling

  • Using the gst-v4l2 pipeline and perform VIC based scaling on Jetson Linux:

    $ gst-launch-1.0 filesrc location=<filename_1080p.mp4>! \
         qtdemux name=demux ! h264parse ! nvv4l2decoder ! \
         nvvidconv interpolation-method=1 ! \
         'video/x-raw(memory:NVMM), format=(string)I420, width=1280, \
         height=720' ! nvdrmvideosink -e
    
  • Using the gst-v4l2 pipeline and perform CUDA-based scaling on an integrated GPU:

    $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! \
         qtdemux name=demux ! h264parse ! nvv4l2decoder ! \
         nvvidconv interpolation-method=1 compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw(memory:NVMM), format=(string)I420, width=1280, \
         height=720' ! nv3dsink -e
    
  • Using the gst-v4l2 pipeline and perform CUDA-based scaling on a dedicated GPU:

    $ gst-launch-1.0 filesrc location=<filename_1080p.mp4> ! \
         qtdemux ! h264parse ! nvv4l2decoder cudadec-memtype=1 ! \
         nvvidconv interpolation-method=1 compute-hw=GPU \
         nvbuf-memory-type=nvbuf-mem-cuda-device ! \
         'video/x-raw(memory:NVMM), format=(string)NV12, width=1280, \
         height=720' ! nveglglessink -e
    

EGLStream Producer Example

The NVIDIA proprietary nveglstreamsrc and nvvideosink GStreamer-1.0 plugins allow simulation of an EGLStream producer pipeline (for preview only.)

To simulate an EGLStream producer pipeline, enter the command:

$ nvgstcapture-1.0 --camsrc=3

EGL Image Transform Example

The NVIDIA proprietary nvegltransform GStreamer-1.0 plugin allows simulation of an EGLImage transform pipeline.

To simulate an EGL Image transform pipeline:

  • Using the gst-v4l2 pipeline:

    $ gst-launch-1.0 filesrc location=<filename_h264_1080p.mp4> ! \
         qtdemux ! h264parse ! nvv4l2decoder ! nvegltransform ! nveglglessink -e
    

GStreamer Build Instructions

Use the gst-install script to install a specific GStreamer version. This section provides a procedure for building current versions of GStreamer.

To build GStreamer using gst-install

  1. Run the command:

    $ gst-install [--prefix=<install_path>] [--version=<version>]
    

    Where:

    • <install_path> is the location where GStreamer is to be installed.

    • <version> is the GStreamer version to be installed.

  2. Run the commands:

    $ export LD_LIBRARY_PATH=<install_path>/lib/aarch64-linux-gnu
    $ export PATH=<install_path>/bin:$PATH
    

    Where <install_path> is the location GStreamer has been installed.

For example:

$ gst-install --prefix=/home/ubuntu/gst-1.16.2 --version=1.16.2
$ export LD_LIBRARY_PATH=/home/ubuntu/gst-1.16.2/lib/aarch64-linux-gnu
% export PATH=/home/ubuntu/gst-1.16.2/bin:$PATH

To build GStreamer manually

  1. Download the latest version of GStreamer, available from the freedesktop.org GStreamer source directory.

    You need the following files from version 1.16.2:

    • gstreamer-1.16.2.tar.xz

    • gst-plugins-base-1.16.2.tar.xz

    • gst-plugins-good-1.16.2.tar.xz

    • gst-plugins-bad-1.16.2.tar.xz

    • gst-plugins-ugly-1.16.2.tar.xz

  2. To install required packages, enter the command:

    $ sudo apt-get install build-essential dpkg-dev flex bison \
          autotools-dev automake liborc-dev autopoint libtool \
          gtk-doc-tools libgstreamer1.0-dev
    
  3. In the home (~) directory, create a subdirectory named gst_<version>, where <version> is the version number of GStreamer you are building.

  4. Copy the downloaded .tar.xz files to the gst_<version> directory.

  5. Uncompress the .tar.xz files in the gst_<version> directory.

  6. Set the environment variable PKG_CONFIG_PATH. by entering the command:

    $ export PKG_CONFIG_PATH=/home/ubuntu/gst_1.16.2/out/lib/pkgconfig
    
  7. Build GStreamer (in this example, gstreamer-1.16.2) by entering the commands:

    $ ./configure --prefix=/home/ubuntu/gst_1.16.2/out
    $ make
    $ make install
    
  8. Build gst-plugins-base-1.16.2 by entering the commands:

    $ sudo apt-get install libxv-dev libasound2-dev libtheora-dev \
          libogg-dev libvorbis-dev
    $ ./configure --prefix=/home/ubuntu/gst_1.16.2/out
    $ make
    $ make install
    
  9. Build gst-plugins-good-1.16.2 by entering the commands:

    $ sudo apt-get install libbz2-dev libv4l-dev libvpx-dev \
          libjack-jackd2-dev libsoup2.4-dev libpulse-dev
    $ ./configure --prefix=/home/ubuntu/gst_1.16.2/out
    $ make
    $ make install
    
  10. Obtain and build gst-plugins-bad-1.16.2 by entering the commands:

    $ sudo apt-get install faad libfaad-dev libfaac-dev
    $ ./configure --prefix=/home/ubuntu/gst_1.16.2/out
    $ make
    $ make install
    
  11. Obtain and build gst-plugins-ugly-1.16.2 by entering the commands:

    $ sudo apt-get install libx264-dev libmad0-dev
    $ ./configure --prefix=/home/ubuntu/gst_1.16.2/out
    $ make
    $ make install
    
  12. Set the environment variable LD_LIBRARY_PATH by entering the command:

    $ export LD_LIBRARY_PATH=/home/ubuntu/gst_1.16.2/out/lib/
    
  13. Copy the NVIDIA gstreamer-1.0 libraries to the gst_1.16.2 plugin directory by entering the commands:

    $ cd /usr/lib/aarch64-linux-gnu/gstreamer-1.0/
    $ cp libgstnv\* ~/gst_1.16.2/out/lib/gstreamer-1.0/
    

    The NVIDIA gstreamer-1.0 libraries include:

    • libgstnvarguscamera.so

    • libgstnvv4l2camerasrc.so

    • libgstnvcompositor.so

    • libgstnvdrmvideosink.so

    • libgstnveglglessink.so

    • libgstnveglstreamsrc.so

    • libgstnvegltransform.so

    • libgstnvivafilter.so

    • libgstnvjpeg.so

    • libgstnvtee.so

    • libgstnvvidconv.so

    • libgstnvvideo4linux2.so

    • libgstnvvideocuda.so

    • libgstnvvideosink.so

    • libgstnvvideosinks.so

nvgstcapture-1.0 Reference

This section describes the nvgstcapture-1.0 application.

Note

By default, nvgstcapture-1.0 only supports the ARGUS API using the nvarguscamerasrc plugin. The legacy nvcamerasrc plugin is no longer supported.

Command Line Options

To display command usage information, run nvgstcapture-1.0 with one of these command line options:one of these command line options:

  • -h or --help: Shows command line options except for GStreamer options.

  • --help-all: Shows all command line options.

  • --help-get: Shows GStreamer command line options.

The following table describes the application’s other command-line options:

nvgstcapture-1.0 command line options
Option Description Value and examples
--prev_res Preview width and height. Range: 2 to 8 (3840×2160)

--prev_res=3

--cus-prev-res Preview custom width and height (CSI only). --cus-prev-res=1920x1080
--image_res Image width and height. Range: 2 to 12 (5632x4224)

--image_res=3

--video-res Video width and height. Range: 2 to 9 (3896x2192)

--video-res=3

--camsrc Camera source to use. 0: V4L2
1: csi (default)
2: videotest
3: eglstream
-m
--mode
Capture mode. 1: still
2: video
-v
--video_inc
Video encoder type. 0: h264[HW]
1: vp8 [HW, not supported on Jetson AGX Xavier series]
2: h265[HW]
3: vp9[HW]
-p
--hw-enc-path
Framework Type. 0: CMX
1: V4L2
-b
--enc-bitrate
Video encoding bit-rate (in bytes). --enc-bitrate=4000000
--enc-controlrate Video encoding bit rate control method. 0: disabled
1: variable (default)
2: constant

--enc-controlrate=1

--enc-EnableTwopassCBR Enable two-pass CBR while encoding. 0: disabled
1: enabled

--enc-EnableTwopassCBR=1

--enc-profile Video encoder profile (only for H.264). 0: baseline
1: main
2: high
-j, --image_enc Image encoder type. 0: jpeg_SW[jpegenc]
1: jpeg_HW[nvjpegenc]
-k, --file_type Container file type. 0: MP4
1: 3GP
2: MKV
--file-name Captured file name. ``nvcamtest`` is used by default.
--color-format Color format to use. 0: I420
1: NV12[For CSI only and default for CSI]
2: YUY2[For V4L2 only, default for V4L2]
--orientation Camera sensor orientation value.
--eglConfig EGL™ window coordinates in (x, y) order. --eglConfig="50 100"
-w
--whitebalance
Capture white balance value.
--timeout Capture timeout value.
--saturation Camera saturation value.
--sensor-id Camera Sensor ID value.
--display-id [For nvoverlaysink only] Display ID value.
--overlayConfig Overlay configuration options index and coordinates in (index, x, y, width, height) order. --overlayConfig="0, 0, 0, 1280, 720"
--cap-dev-node Video capture device node. 0: /dev/video0[default]
1: /dev/video1
2: /dev/video2

--cap-dev-node=0

--svs=<chain>

Where <chain> is a chain of GStreamer elements:

For USB, specifies a chain for video preview.

For CSI only, use nvoverlaysink or nvdrmvideosink.

--exposuretimerange Property to adjust exposure time range, in nanoseconds. --exposuretimerange="34000 358733000"
--gainrange Property to adjust gain range. --gainrange="1 16"
--ispdigitalgainrange Property to adjust digital gain range. Range value from 1 to 256.

--ispdigitalgainrange="1 8"

--aelock Enable AE lock. Default is disabled.
--awblock Enable AWB lock. Default is disabled.
--exposurecompensation Property to adjust exposure compensation. Range value from −2.0 to 2.0.

--exposurecompensation=0.5

--aeantibanding Property to set the auto exposure antibanding mode. Range value from 0 to 3.

--aeantibanding=2

--tnr-mode Property to select temporal noise reduction mode. --tnr-mode=2
--tnr-strength Property to adjust temporal noise reduction strength. --tnr-strength=0.5
--ee-mode Property to select edge enhancement mode. --ee-mode=2
--ee-strength Property to adjust edge enhancement strength. --ee-strength=0.5

CSI Camera Supported Resolutions

CSI camera supports the following image resolutions for Nvarguscamera:

  • 640×480

  • 1280×720

  • 1920×1080

  • 2104×1560

  • 2592×1944

  • 2616×1472

  • 3840×2160

  • 3896×2192

  • 4208×3120

  • 5632×3168

  • 5632×4224

CSI Camera Runtime Commands

Options for Nvarguscamera

The following table describes CSI camera runtime command line options for Nvarguscamera.

Nvarguscamera command line options

Command

Description

Value and examples

h

Help.

q

Quit.

mo:<value>

Set capture mode.

1: image

2: video

gmo

Get capture mode.

so:<val>

Set sensor orientation.

0: none

1: rotate counter-clockwise 90°

2: rotate 180°

3: rotate clockwise 90°

gso

Get sensor orientation.

wb:<value>

Set white balance mode.

0: off

1: auto

2: incandescent

3: fluorescent

4: warm-fluorescent

5: daylight

6: cloudy-daylight

7: twilight

8: shade

9: manual

gwb

Get white balance mode.

st:<value>

Set saturation.

0-2

Example: st:1.25

gst

Get saturation.

j

Capture one image.

jx<sec>

Capture after a delay of <sec> seconds.

Example: jx5000 for a 5 second delay.

j:<value>

Capture <count> images in succession.

Example: j:6 to capture 6 images.

0

Stop recording video.

1

Start recording video.

2

Video snapshot (while recording video).

gpcr

Get preview resolution.

gicr

Get image capture resolution.

gvcr

Get video capture resolution.

USB Camera Runtime Commands

The following table describes USB camera runtime commands.

USB camera runtime commands

Command

Description

Value and examples

h

Help.

q

Quit.

mo:<value>

Set capture mode.

1: image

2: video

gmo

Get capture mode.

j

Capture one image.

jx<ms>

Capture after a delay of <ms> milliseconds.

Example: jx5000 to capture after a 5000 millisecond (5 second) delay.

j:<n>

Capture <n> images in succession.

Example: j:6 to capture 6 images.

1

Start recording video.

0

Stop recording video.

pcr:<value>

Set preview resolution.

0: 176×144

1: 320×240

2: 640×480

3: 1280×720

gpcr

Get preview resolution.

gicr

Get image capture resolution.

gvcr

Get video capture resolution.

br:<value>

Set encoding bit rate in bytes.

Example: br:4000000

gbr

Get encoding bit rate.

cdn:<value>

Set capture device node.

0: //dev/video0

1: //dev/video1

2: //dev/video2

gcdn

Get capture device node.

Runtime Video Encoder Configuration Options

The following table describes runtime video encoder configuration options supported for Nvarguscamera.

Runtime video encoder options

Command

Description

Value and examples

br:<val>

Sets encoding bit-rate in bytes.

Example: br:4000000

gbr

Gets encoding bit-rate in bytes.

ep:<val>

Sets encoding profile (for H.264 only).

0: baseline

1: main

2: high

Example: ep:1

gep

Gets encoding profile (for H.264 only).

Enter ‘f’

Forces IDR frame on video encoder (for H.264 only).

Notes

  • nvgstcapture-1.0 generates image and video output files in the same directory as the application itself.

  • Filenames are respectively in these formats:

    • Image content: nvcamtest_<pid>_<sensor_id>_<counter>.jpg

    • Video content: nvcamtest_<pid>_<sensor_id>_<counter>.mp4

    Where:

    • <pid> is the process ID.

    • <sensor_id> is the sensor ID.

    • <counter> is a counter starting from 0 each time the application is run.

  • Rename or move files between runs to avoid overwriting results you want to save.

  • The application supports native capture mode (video only) by default.

  • Advanced features, such as setting zoom, brightness, exposure, and whitebalance levels, are not supported for USB cameras.

nvgstplayer-1.0 Reference

This section describes the operation of the the nvgstplayer-1.0 application.

nvgstplayer-1.0 Command Line Options

Note

To list supported options, enter the command:

$ nvgstplayer-1.0 --help

This table describes nvgstplayer-1.0 command line options.

nvgstplayer-1.0 command line options
Option Description and examples
-u <path>
--urifile <path>

Path of the file containing the URIs.

Example: -u my_uri.txt

-i <uri>
--uri <uri>

Input URI.

Examples:

-uri file:///home/ubuntu/movie.avi

-uri https://www.joedoe.com/foo.ogg

-e <path>
--elemfile <path>

Elements (Properties) file.

The element file may contain an audio or video processing elements chain.

Examples:

[sas]

pipe=alsasink # device=demixer

-x
--cxpr

Command sequence expression.

Example: -cxpr="r5 s0"

-n <n>
--loop <n>

Number of times to play the media.

-c <n>
--audio-track <n>

If a stream has multiple audio tracks, specifies the track number to play

-v <n>
--video-track <n>

If a stream has multiple video tracks, specifies the track number to play.

-a <sec>
--start <sec>

Point to start playback, in seconds from the beginning of the media segment.

-d <sec>
--duration <sec>

Duration of playback, in seconds.

--no-sync

Disable AV sync.

--disable-dpms

Unconditionally disable DPMS/ScreenBlanking during operation; re-enable on exit.

--stealth

Operate in stealth mode, staying alive even when no media is playing.

--bg

Operate in background mode, ignoring keyboard input.

--use-playbin

Use Playbin GStreamer element.

--no-audio

Disable audio.

--no-video

Disable video.

--disable-anative

Disable native audio rendering.

--disable-vnative

Disable native video rendering.

--use-buffering

Enable decodebin property for emitting GST_MESSAGE_BUFFERING based on low and high percent thresholds.

-l <pct>
--low-percent <pct>

Low threshold for buffering to start, in pct.

-j <pct>
--high-percent <pct>

High threshold for buffering to finish, in percent.

--loop-forever

Play the URI(s) in an endless loop.

-t <sec>
--max-size-time <sec>

Maximum time in queue, in seconds (0=automatic).

-y <n>
--max-size-bytes <n>

Maximum amount of memory in the queue, in bytes (0=automatic).

-b <n>
--max-size-buffers <n>

Maximum number of buffers in the queue (0=automatic).

--window-x <n>

X coordinate for player window (for non-overlay rendering).

--window-y <n>

Y coordinate for player window (for non-overlay rendering).

--window-width <n>

Window width (for non-overlay rendering).

--window-height <n>

Window height (for non-overlay rendering).

--disable-fullscreen

Play video in non-full-screen mode (for nveglglessink).

-k <sec>
--image-display-time <sec>

Image display time, in seconds.

--show-tags

Shows tags (metadata), if available.

--stats

Shows stream statistics, if enabled.

--stats-file

File to dump stream statistics, if enabled.

--svd=<chain>

Chain to use for video decoding.

Where <chain> is as described below.
--sad=<chain>

Chain to use for audio decoding.

--svc=<chain>

Chain to use for video postprocessing.

--sac=<chain>

Chain to use for audio postprocessing.

--svs=<chain>

Chain to use for video rendering.

--sas=<chain>

Chain to use for audio rendering.

--shttp=<chain>

Chain to use for HTTP source.

--srtsp=<chain>

Chain to use for RTSP source.

--sudp=<chain>

Chain to use for UDP source.

--sfsrc=<chain>

Chain to use for file source.

<chain> is a chain of GStreamer elements that apply to the specified function. Its value is a set of one or more elements separated by ‘!’. Each element is a set of one or more properties separated by ‘#’.

Examples:

--svd="avdec_h264# skip-frame=1# output-corrupt=false"
--sad="aacparse ! faad# min-latency=4000000"
--svc="videoconvert# qos=0 ! videoscale"
--sac="audioconvert ! audioresample"
--svs="videoconvert ! videoscale ! ximagesink# sync=0"
--sas="audioconvert ! osssink# device=/dev/dsp1# latency-time=20000"

nvgstplayer-1.0 Runtime Commands

This table describes nvgstplayer runtime commands.

nvgstplayer-1.0 runtime commands
Option Description and examples
h Help.
q Quit.
Up arrow
]
Go to next track.
c Restart current track.
Down arrow
[
Go to previous track.
spos Query for position (time from start).
sdur Query for duration.
s<sec>

Seek to <sec> seconds from start.

Example: s5.120

v<pct>

Seek to <pct> percent of the duration.

Example: v54

f<sec>

Shift <sec> seconds relative to current position.

Example: f23.901

Left arrow
<
Seek backward 10 seconds.
Right arrow
>
Seek forward 10 seconds.
p Pause playback.
r Start/resume playback.
z Stop playback.
i:<uri> Enter a single URI.

Video Encoder Features

The respective GStreamer-1.0-based gst-v4l2 video encoders support the following features:

gst-v4l2 video encoder features
Feature H264enc H265enc Vp8enc Vp9enc
profile (Baseline / Main / High) ✓ (all) ✓ (main)
control-rate
bitrate
insert-spsppsatidr
profile
quantization range for I, P, and B frame
iframeinterval
qp-range
bit-packetization
preset-level
slice-header spacing
force-IDR
enable TwoPassCBR
enable CABAC-entropy-coding
enable MVBufferMeta
insert aud
insert vui
num-B-Frames
picture order count type

Supported Cameras

This section describes the supported cameras.

CSI Cameras

  • Jetson AGX Xavier series can capture camera images via CSI interface.

  • Jetson AGX Xavier series supports both YUV and RAW Bayer capture data.

  • GStreamer supports simultaneous capture from multiple CSI cameras. Support is validated using the nvgstcapture application.

  • Capture is validated for SDR, PWL HDR and DOL HDR modes for various sensors using the nvgstcapture application.

  • Jetson AGX Xavier series also support the MIPI CSI virtual channel feature. The virtual channel is a unique channel identifier used for multiplexed sensor streams sharing the same CSI port/brick and CSI stream through supported GMSL (Gigabit Multimedia Serial Link) aggregators.

  • GMSL + VC capture is validated on Jetson AGX Xavier series using the nvgstcapture application. The reference GMSL module (MAX9295-serializer/­MAX9296-deserializer/­IMX390-sensor) is used for validation purposes.

USB 2.0 Cameras

The following camera has been validated on Jetson platforms running Jetson Linux with USB 2.0 ports. This camera is UVC compliant.

Industrial Camera Details

The following USB 3.0 industrial camera is validated on Jetson AGX Xavier series under Jetson Linux:

Characteristics of this camera are:

  • USB 3.0

  • UVC compliant

  • 3840×2160 at 30 FPS; 4224×3156 at 13 FPS

  • Purposeembedded navigation

  • Test using the nvgstcapture app.

  • Issues encountered:

    FPS cannot be fixed. Changes based on exposure.

    FPS cannot be changed. Needs payment to vendor to get the support added to their firmware.