SM Commands
ib sm
ib sm Enables the SM on this node. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm | |
Related Commands | show ib sm | |
Notes |
ib sm accum-log-file
ib sm accum-log-file Adds SM log entries at the end of the current log. | ||
Syntax Description | N/A | |
Default | Enabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm accum-log-file | |
Related Commands | show ib sm accum-log-file | |
Notes |
ib sm allow-both-pkeys
ib sm allow-both-pkeys Enables having both full and limited membership on the same partition. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.4.1100 | |
Example | switch (config) # ib sm allow-both-pkeys | |
Related Commands | defmember | |
Notes |
ib sm babbling-policy
ib sm babbling-policy Enables the SM to disable babbling ports (i.e., generating frequent traps). | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # no ib sm babbling-policy | |
Related Commands | show ib sm babbling-policy | |
Notes | If the babbling policy is enabled, and decides to close a babbling interface (one which sends 129,130,131 traps, for example), the SM disables the port. |
ib sm connect-roots
ib sm connect-roots Forces the routing engine to make connectivity between root switches. | ||
Syntax Description | N/A | |
Default | Enabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm connect-roots | |
Related Commands | show ib sm connect-roots | |
Notes |
|
ib sm calculate-missing-routes
ib sm calculate-missing-routes Enables SM to find and recalculate missing routes without creating credit-loops | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.8.2000 | |
Example | switch (config) # ib sm calculate-missing-routes ib sm calculate-missing-routes: enabled switch (config) # no ib sm calculate-missing-routes ib sm calculate-missing-routes: disabled | |
Related Commands | Show ib sm calculate-missing-routes | |
Notes |
ib sm drop-event-subscriptions
ib sm drop-event-subscriptions Configures IB SM to drop interface subscribe or unsubscribe events. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.4.2008 | |
Example | switch (config) # ib sm drop-event-subscriptions | |
Related Commands | ||
Notes |
ib sm enable-quirks
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm enable-quirks | |
Related Commands | show ib sm enable-quirks | |
Notes |
ib sm exit-on-fatal
ib sm exit-on-fatal Enables the SM to exit upon fatal initialization errors. | ||
Syntax Description | N/A | |
Default | Enabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm exit-on-fatal | |
Related Commands | show ib sm exit-on-fatal | |
Notes |
ib sm force-link-speed
ib sm force-link-speed <speed-options> Defines the SM behavior for PortInfo:LinkSpeedEnabled, PortInfo:LinkSpeedExtEnabled and MLNX ExtendedPortInfo on the switch ports. | ||
Syntax Description | speed-options | The following options are available:
|
Default | Set to PortInfo:LinkSpeedExtSupported | |
Configuration Mode | config | |
History | 3.1.0000 | |
3.4.1604 | Updated Syntax Description, Example, and Notes | |
Example | switch (config) # ib sm force-link-speed sdr ddr qdr fdr10 | |
Related Commands | show ib sm force-link-speed | |
Notes |
|
ib sm force-log-flush
ib sm force-log-flush Forces every log message generated to be flushed. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm force-log-flush | |
Related Commands | show ib sm force-log-flush | |
Notes |
ib sm guid2lid-cache
ib sm guid2lid-cache Allows SM to use cached GUID-to-lid mapping data. When enabled, the SM honors the cached GUID-to-lid mapping information if:
The no form of the command disallows use of cached GUID-to-lid mapping data. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm guid2lid-cache | |
Related Commands | show ib sm guid2lid-cache | |
Notes |
ib sm honor-partitions
ib sm honor-partitions Sets the no_partition_enforcement flag to 0. This setting controls global support for partitioning in the subnet. | ||
Syntax Description | N/A | |
Default | Enabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # no ib sm honor-partitions | |
Related Commands | show ib sm honor-partitions | |
Notes |
|
ib sm hoq-lifetime
ib sm hoq-lifetime <time> Sets the maximum time a frame can wait at the head of a switch-to-switch port queue before it is dropped. | ||
Syntax Description | time | The time is 4.096 uS * 2time. The range of time is 0 to 20. A time of 20 means infinite, and the default value is 18 which translates to about 1 second. |
Default | 0x12 (~ 1 second) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm hoq-lifetime 15 | |
Related Commands | show ib sm hoq-lifetime | |
Notes |
ib sm ignore-other-sm
ib sm ignore-other-sm Ignores all the rules governing SM elections and attempts to manage the fabric. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm ignore-other-sm | |
Related Commands | show ib sm ignore-other-sm | |
Notes |
ib sm ipv6-nsm
ib sm ipv6-nsm Consolidates IPv6 SNM group joins to 1 MC group per-MGID PKEY. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm ipv6-nsm | |
Related Commands | show ib sm ipv6-nsm | |
Notes |
ib sm lash
ib sm lash {do-mesh-analysis | start-vl <vl-value>} Modifies “lash” routing method parameters. | ||
Syntax Description | do-mesh-analysis | Enables SM “lash” routing for mesh analysis |
start-vl <vl-value> | Configures the starting VL for SM “lash” routing for mesh analysis (assuming that lash routing is enabled) | |
Default | do-mesh-analysis: Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm lash do-mesh-analysis | |
Related Commands | show ib sm lash do-mesh-analysis | |
Notes |
ib sm leafhoq-lifetime
ib sm leafhoq-lifetime <time> Sets the maximum time a frame can wait at the head of a switch-to-CA_or_Router port queue before it is dropped. | ||
Syntax Description | time | The time is 4.096 uS * 2time. The range of time is 0 to 20. A time of 20 means infinite, and the default value is 16 which translates to about 268 millisecond. |
Default | 0x10 (about 268 mS) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm leafhoq-lifetime 8 | |
Related Commands | show ib sm leafhoq-lifetime | |
Notes |
ib sm leafvl-stalls
ib sm leafvl-stalls <count> Sets the number of sequential frame drops that cause a switch-to-CA_or_Router port to enter the VLStalled state. | ||
Syntax Description | count | Range: 1-255 |
Default | 7 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm leafvl-stalls 3 | |
Related Commands | show ib sm leafvl-stalls | |
Notes |
ib sm lmc
ib sm lmc <mask> Sets the LID Mask Control (LMC) value to be used on this subnet. | ||
Syntax Description | mask | Range: 0-7 |
Default | The default value is 0, which means that every port has exactly one unique LID. | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm lmc 7 | |
Related Commands | show ib sm lmc | |
Notes |
ib sm lmc-esp0
ib sm lmc-esp0 Sets the LMC for the subnet to be used for Enhanced Switch Port 0. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm lmc-esp0 | |
Related Commands | show ib sm lmc-esp0 | |
Notes |
ib sm log-flags
ib sm log-flags [all] [debug] [error] [frames] [funcs] [info] [none] [routing] [verbose] Controls what messages the SM logs. | ||
Syntax Description | all | Turns on all the flags that follow (error info verbose debug funcs frames routing). |
debug | Logs diagnostic messages, high volume. | |
error | Logs error messages. | |
frames | Logs all SMP and GMP frames. | |
funcs | Logs function entry/exit, very high volume. | |
info | Logs basic messages, low volume. | |
none | Turns off all logging flags. | |
routing | Logs FDB routing information. | |
verbose | Logs interesting stuff, moderate volume. | |
Default | 0x3 (error, info) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm log-flags error verbose funcs frames | |
Related Commands | show ib sm log-flags | |
Notes |
|
ib sm log-max-size
ib sm log-max-size <size> Sets the maximum size of the log file to be <size> megabytes. | ||
Syntax Description | size | Range: 1-60 |
Default | 20 MBytes | |
Configuration Mode | config | |
History | 3.1.0000 | |
3.5.1000 | Updated Syntax Description, and Default | |
Example | switch (config) # ib sm log-max-size 50 | |
Related Commands | show ib sm log-max-size | |
Notes |
|
ib sm m-key
ib sm m-key <m-key> Sets the MKey used by SM. | ||
Syntax Description | m-key | 64-bit MKey |
Default | 00:00:00:00:00:00:00:00 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm m-key 00:00:00:00:00:00:00:05 | |
Related Commands | show ib sm m-key | |
Notes |
ib sm max-op-vls
ib sm max-op-vls <count> Sets the maximum number of VLs supported on this subnet. | ||
Syntax Description | count | Possible values: 1, 2, 4, 8, or 15 |
Default | 4 | |
Configuration Mode | config | |
History | 3.1.0000 | |
3.10.1000 | Updated default value from 15 to 4 | |
Example | switch (config) # ib sm max-op-vls 4 | |
Related Commands | show ib sm max-op-vls | |
Notes |
ib sm max-reply-time
ib sm max-reply-time <time> Sets the maximum time the SM waits for a reply before the transaction times out. | ||
Syntax Description | time | Must be an integer (in milliseconds) |
Default | 200 milliseconds | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm max-reply-time 500 | |
Related Commands | show sm max-reply-time | |
Notes |
ib sm max-reverse-hops
ib sm max-reverse-hops <max-reverse-hops> Sets the maximum number of hops from the top switch to an I/O node. | ||
Syntax Description | N/A | |
Default | 0 hops | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm max-reverse-hops 500 | |
Related Commands | show ib sm max-reverse-hops | |
Notes |
ib sm aguid_default_hop_limit
ib sm aguid-default-hop-limit <count> Configures the default value for hop limit returned in path records where either the source or destination are alias an GUID. | ||
Syntax Description | count | Number of concurrent management packets (must be an integer) |
Default | 1 | |
Configuration Mode | config | |
History | 3.6.6102 | |
Example | switch (config) # ib sm aguid-default-hop-limit 3 | |
Related Commands | show ib sm aguid-default-hop-limit | |
Notes |
ib sm max-wire-smps2
ib sm max-wire-smps2 <count> Sets the maximal timeout based outstanding SM management packets. | ||
Syntax Description | count | Number of concurrent management packets. The value must be an integer. |
Default | 4 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm max-wire-smps 8 | |
Related Commands | show ib sm max-wire-smps2 | |
Notes |
ib sm m-key
ib sm m-key <mkey> Configures the MKey used by the SM. | ||
Syntax Description | mkey | 64-bit MKey |
Default | 00:00:00:00:00:00:00:00 | |
Configuration Mode | config | |
History | 3.1.0000 | |
3.6.2002 | Added no form of the command | |
3.7.0000 | Added note | |
Example | switch (config) # ib sm m-key 11:33:55:77:99:aa:cc:ee | |
Related Commands | ib sm mkey-lease | |
Notes |
|
ib sm mkey-lease
ib sm mkey-lease <time> Configures the lease period used when MKey is non-zero. | ||
Syntax Description | time | MKey lease period in seconds |
Default | 0 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm mkey-lease 660 | |
Related Commands | show ib sm mkey-lease | |
Notes |
ib sm mkey-lookup
ib sm mkey-lookup Enables using a file cache (guid2mkey) to resolve unknown node MKey. | ||
Syntax Description | N/A | |
Default | Enabled | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm mkey-lookup | |
Related Commands | show ib sm mkey-lookup | |
Notes | MKey lookup is a boolean value that controls how the SM finds the MKey of ports |
ib sm mkey-protect-level
ib sm mkey-protect-level <level> Controls what data is returned to a get_PortInfo MAD request when the MKey in the request does not match the MKey on the port. | ||
Syntax Description | level |
|
Default | 0 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm mkey-protect-level 0 | |
Related Commands | show ib sm mkey-protect-level | |
Notes |
ib sm msgfifo-timeout
ib sm msgfifo-timeout <time> Sets the time value to be used by the subnet administrator to control when a BUSY status is returned to a client. | ||
Syntax Description | time | In milliseconds |
Default | 10 seconds | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm msgfifo-timeout 50000 | |
Related Commands | show ib sm msgfifo-timeout | |
Notes | If there is more than one message in the SA queue, and it has been there longer than time milliseconds, all additional incoming requests are immediately replied to with BUSY status. |
ib sm multicast
ib sm multicast Enables the SM to support multicasts on the fabric. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm multicast | |
Related Commands | show ib sm multicast | |
Notes |
ib sm no-client-rereg
ib sm no-client-rereg Enables client re-registration requests. | ||
Syntax Description | N/A | |
Default | disable | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm no-client-rereg | |
Related Commands | show ib sm no-client-rereg | |
Notes |
ib sm overrun-trigger
ib sm overrun-trigger <count> Enables SMA to generate standard InfiniBand trap number 130 when the number of local buffer overrun errors equals the count value, and the port’s SMA supports traps. | ||
Syntax Description | count | Range: 0-255 |
Default | 8 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm overrun-trigger 3 | |
Related Commands | show ib sm overrun-trigger | |
Notes | Refer to the InfiniBand Architecture Specification V1 r1.2.1, section 14.2.5.1 table 131: Traps. |
ib sm packet-life-time
ib sm packet-life-time <time> Sets the maximum time a frame can live in a switch. | ||
Syntax Description | time | The time is 4.096 uS * 2*<time>. Range: 0-20. A time of 20 means infinite. The value 0x14 disables this mechanism. |
Default | 0x12 (about 1 second) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm packet-life-time 20 | |
Related Commands | show ib sm packet-life-time | |
Notes |
ib sm phy-err-trigger
ib sm phy-err-trigger <count> Enables SMA to generate trap 129 when the number of local link integrity errors equals the <count> value, and the port’s SMA supports traps. | ||
Syntax Description | count | Range: 0-255 |
Default | 8 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm phy-err-trigger 5 | |
Related Commands | show ib sm phy-err-trigger | |
Notes |
ib sm polling-retries
ib sm polling-retries <value> This variable defines the number of consecutive times an active SM must fail to respond before it is declared dead. | ||
Syntax Description | value | Must be an integer |
Default | 4 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm polling-retries 8 | |
Related Commands | show ib sm polling-retries | |
Notes | The time between when the active SM fails and the time this SM declares it dead is: (sm_sminfo_polling_timeout * value) milliseconds. |
ib sm port-prof-switch
ib sm port-prof-switch Enables the counting of adapters, routers, and switches routed through links. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm port-prof-switch | |
Related Commands | show ib sm port-prof-switch | |
Notes |
ib sm reassign-lids
ib sm reassign-lids Controls the ability of the SM to reassign LIDs to nodes it finds already configured with a valid LID. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm reassign-lids | |
Related Commands | show ib sm reassign-lids | |
Notes |
|
ib sm reset-config
ib sm reset-config Resets all SM configuration options to defaults. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm reset-config | |
Related Commands | ||
Notes |
ib sm root-guid
ib sm root-guid <guid> Adds a root GUID for the SM. | ||
Syntax Description | guid | The root GUID number in hexadecimal notation |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config)# ib sm root-guid aa:bb:00:11:22:33:44:55 | |
Related Commands | show ib sm routing-engines | |
Notes | The list of root GIDs are relevant when IB SM is running on the switch, and the routing algorithm is up-down or fat-tree. |
ib sm routing-engines
ib sm routing-engines [dor] [file] [ftree] [lash] [minhop] [none] [updn] Sets the routing engine of the SM. | ||
Syntax Description | dor | Includes “dor” engine in selection of routing engines |
file | Includes “file” engine in selection of routing engines | |
ftree | Includes “ftree” engine in selection of routing engines | |
lash | Includes “lash” engine in selection of routing engines | |
minhop | Includes “minhop” engine in selection of routing engines | |
none | No routing engines specified; use SM default(s) | |
updn | Includes “up/down” engine in selection of routing engines | |
Default | None | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm routing-engines none | |
Related Commands | show ib sm routing-engines | |
Notes | Multiple routing engines can be specified separated by spaces so that specific ordering of routing algorithms will be tried if earlier routing engines fail. |
ib sm rtr-aguid-enable
ib sm rtr-aguid-enable <value> Configures SM alias GUID control option. | ||
Syntax Description | value | Possible values:
|
Default | 0 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm rtr-aguid-enable 1 | |
Related Commands | ||
Notes |
ib sm rtr-pr-flow-label
ib sm rtr-pr-flow-label <value> Configures inter-subnet PathRecord FlowLabel. | ||
Syntax Description | value | Range: 0-1048575 |
Default | 0 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm rtr-pr-flow-label 1 | |
Related Commands | ||
Notes |
ib sm rtr-pr-mtu
ib sm rtr-pr-mtu <value> Configures inter-subnet PathRecord MTU. | ||
Syntax Description | value | Possible values: 256, 512, 1K, 2K, 4K |
Default | 2K | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm rtr-pr-mtu 2k | |
Related Commands | ||
Notes |
ib sm rtr-pr-rate
ib sm rtr-pr-rate <value> Configures inter-subnet PathRecord rate. | ||
Syntax Description | value | Possible values: 2.5, 5, 10, 14, 20, 25, 40, 56, 100 |
Default | 100 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm rtr-pr-rate 5 | |
Related Commands | ||
Notes |
ib sm rtr-pr-sl
ib sm rtr-pr-sl <value> Configures inter-subnet PathRecord SL. | ||
Syntax Description | value | Range: [0-15] |
Default | 0 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # rtr-pr-sl 0 | |
Related Commands | ||
Notes |
ib sm rtr-pr-tclass
ib sm rtr-pr-tclass <value> Configures inter-subnet PathRecord T-class. | ||
Syntax Description | value | Range: 0-255 |
Default | 0 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm rtr-pr-tclass 1 | |
Related Commands | ||
Notes |
ib sm sa-key
ib sm sa-key <SA_Key> Sets the SA_Key 64-bit value used by SA to qualify that a query is “trusted”. | ||
Syntax Description | SA Key | 64 bit |
Default | 00:00:00:00:00:00:00:01 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sa-key 5 | |
Related Commands | show ib sm sa-key | |
Notes | OpenSM version 3.2.1 and lower used the default value of “1” in host byte order. You may need to change this value to inter-operate with older subnet managers. |
ib sm single-thread
ib sm single-thread Enables the Subnet Manager to use a single thread to service all requests. | ||
Syntax Description | N/A | |
Default | Disabled (use multiple service threads) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm single-thread | |
Related Commands | show ib sm single-thread | |
Notes |
ib sm sm-inactive
ib sm sm-inactive Configures the SM to start in the “inactive” SM state. This option can be used to run a standalone system without the SM/SA function. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sm-inactive | |
Related Commands | show ib sm sm-inactive | |
Notes |
ib sm sm-key
ib sm sm-key <SM_Key> Sets the SM 64-bit SM_Key. | ||
Syntax Description | SM Key | 64 bit |
Default | 00:00:00:00:00:00:00:01 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sm-key 00:00:00:00:00:00:00:05 | |
Related Commands | show ib sm sm-key | |
Notes | OpenSM version 3.2.1 and lower used the default value of “1” in host byte order. You may need to change this value to inter-operate with older subnet managers. |
ib sm sm-priority
ib sm sm-priority <priority> Prioritizes the desired SM compared to other SMs on the fabric. | ||
Syntax Description | priority | Range: 0-15 |
Default | 0 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sm-priority 1 | |
Related Commands | show ib sm sm-priority | |
Notes | If two or more active SMs have the same highest priority, the one with the lowest port GUID manages the fabric. |
ib sm sm-sl
ib sm sm-sl <sm-sl> Sets the SM service level for SM/SA communication. | ||
Syntax Description | sm-sl | 0-15 |
Default | 0 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sm-sl 10 | |
Related Commands | show ib sm sm-sl | |
Notes | Selects the SL that is used for MADs. |
ib sm sminfo-poll-time
ib sm sminfo-poll-time <time> This variable controls the timeout between two polls of an active subnet manager. | ||
Syntax Description | time | In milliseconds |
Default | 10 seconds | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sminfo-poll-time 15 | |
Related Commands | show ib sm sminfo-poll-time | |
Notes |
ib sm subnet-prefix
ib sm subnet-prefix <prefix> Sets the SM “Subnet Prefix” used to create scope qualifiers for all elements managed by the SM. | ||
Syntax Description | prefix | 64 bit |
Default | FE:80:00:00:00:00:00:00 | |
Configuration Mode | config | |
History | 3.6.1002 | |
3.6.2002 | Added no form of the command | |
Example | switch (config) # ib sm subnet-prefix ff:ff:ff:ff:ff:ff:ff:00 | |
Related Commands | show ib sm subnet-prefix | |
Notes | The default value is also the InfiniBand default for a locally administered subnet. |
ib sm subnet-prefix-override
ib sm subnet-prefix-override Disables IB Router subnet prefix checking. | ||
Syntax Description | N/A | |
Default | Enabled | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm subnet-prefix-override | |
Related Commands | show ib sm subnet-prefix-override | |
Notes |
ib sm subnet-prefix-override
ib sm max-smps-timeout <Timeout> Sets timeout for SMPs between max_wire_smps & max_wire_smps2 | ||
Syntax Description | timeout | Timeout in seconds |
Default | N/A | |
Configuration Mode | config | |
History | 3.8.3000 | |
Example | switch (config) # ib sm max-smps-timeout 22 | |
Related Commands | ||
Notes |
ib sm subnet-timeout
ib sm subnet-timeout <time> Sets the global per-port subnet timeout value (PortInfo:SubnetTimeOut). This value also controls the maximum trap frequency in which no traps are allowed to be sent faster than the subnet_timeout value. | ||
Syntax Description | time | The actual timeout is 4.096 uS * 2*<time>. The range of time is 0-31 for this parameter which supports 32 discrete time values between 4 uS and about 2.4 hours. |
Default | 0x12 (About 1 second) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm subnet-timeout 5 | |
Related Commands | show ib sm subnet-timeout | |
Notes | If the SMA generates a sequence of traps, the interval between successive traps should not be smaller than <time>. |
ib sm sweep-interval
ib sm sweep-interval <time> Specifies the time between subnet sweeps. | ||
Syntax Description | time | Range: Between 0 and 36000 seconds; 0—disable |
Default | 10 seconds | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sweep-interval 20 | |
Related Commands | show ib sm sweep-interval | |
Notes |
ib sm sweep-on-trap
ib sm sweep-on-trap Enables every TRAP received by the SM to initiate a heavy sweep in addition to the processing required by the TRAP. | ||
Syntax Description | N/A | |
Default | enable | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm sweep-on-trap | |
Related Commands | show ib sm sweep-on-trap | |
Notes | More than 10 successive identical TRAPs disable the automatic sweep behavior until at least one different TRAP has been received. |
ib sm transaction-retries
ib sm transaction-retries <transaction-retries-count> Sets the maximum retries for failed transactions. | ||
Syntax Description | transaction-retries-count | Must be an integer |
Default | 3 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm transaction-retries 10 | |
Related Commands | show ib sm transaction-retries | |
Notes |
ib sm use-heavy-sweeps
ib sm use-heavy-sweeps Turns every fabric sweep to a heavy sweep. | ||
Syntax Description | N/A | |
Default | disable | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm use-heavy-sweeps | |
Related Commands | show ib sm use-heavy-sweeps | |
Notes |
ib sm use-ucast-cache
ib sm use-ucast-cache Enables the SM to use cached routine data (LMC=0 only). | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm use-ucast-cache | |
Related Commands | show ib sm use-ucast-cache | |
Notes |
ib sm vl-stalls
ib sm vl-stalls <count> Sets the number of sequential frame drops that cause a switch-to-switch port to enter the VLStalled state. | ||
Syntax Description | count | 1-255 |
Default | 7 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib sm vl-stalls 10 | |
Related Commands | show ib sm vl-stalls | |
Notes |
ib sm virt
ib sm virt {enable | disable | ignore} Configures IB SM port virtualization support. | ||
Syntax Description | enable | IB SM supports virtualization, and configures virtual ports |
disable | IB SM disables virtual ports | |
ignore | IB SM ignores virtual ports and does not change their configuration | |
Default | Ignore | |
Configuration Mode | config | |
History | 3.4.2008 | |
Example | switch (config) # ib sm virt configure | |
Related Commands | ||
Notes |
ib sm virt-default-hop-limit
ib sm virt-default-hop-limit <value> Configures the default value for hop limit to be returned in path records. | ||
Syntax Description | value | Range: 0-255 |
Default | 2 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm virt-default-hop-limit 3 | |
Related Commands | ||
Notes |
ib sm virt-max-ports-in-process
ib sm virt-max-ports-in-process <value> Configures the maximum number of ports to be processed simultaneously. | ||
Syntax Description | value | Range: 0-65535 |
Default | 4 | |
Configuration Mode | config | |
History | 3.6.2002 | |
Example | switch (config) # ib sm virt-max-ports-in-process 5 | |
Related Commands | ||
Notes |
show ib sm
show ib sm Displays the SM admin state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm | |
Related Commands | ib sm | |
Notes |
show ib sm accum-log-file
show ib sm accum-log-file Displays the accum-log-file configuration. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm accum-log-file | |
Related Commands | ib sm accum-log-file | |
Notes |
show ib sm babbling-policy
show ib sm babbling-policy Displays the ability of the SM to disable babbling ports (i.e., generating frequent traps). | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm babbling-policy | |
Related Commands | ib sm babbling-policy | |
Notes |
show ib sm calculate-missing-routes
Show ib sm calculate-missing-routes Display option allowing SM to find and recalculate missing routes without creating credit-loops | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.8.2000 | |
Example | switch (config) # ib sm calculate-missing-routes ib sm calculate-missing-routes: enabled switch (config) # no ib sm calculate-missing-routes ib sm calculate-missing-routes: disabled | |
Related Commands | ib sm calculate-missing-routes | |
Notes |
show ib sm connect-roots
show ib sm connect-roots Displays the IBA compliant multi-stage switch directive. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm connect-roots | |
Related Commands | ib sm connect-roots | |
Notes |
show ib sm enable-quirks
show ib sm enable-quirks Displays if the SM uses high risk features and handles HW workarounds. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm enable-quirks | |
Related Commands | ib sm enable-quirks | |
Notes |
show ib sm exit-on-fatal
show ib sm exit-on-fatal Displays if the SM exits upon a fatal error. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm exit-on-fatal | |
Related Commands | ib sm exit-on-fatal | |
Notes |
show ib sm fdr10
show ib sm fdr10 Displays the status of the SM use of FDR10. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm fdr10 | |
Related Commands | ||
Notes |
show ib sm force-link-speed
show ib sm force-link-speed Displays SM behavior for PortInfo:LinkSpeedEnabled parameter on switch ports. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
3.4.1604 | Updated Syntax Description, Example and Notes | |
Example | switch (config) # show ib sm force-link-speed | |
Related Commands | ib sm force-link-speed | |
Notes | Possible outputs:
|
show ib sm force-link-speed-ext
show ib sm force-link-speed-ext Displays SM behavior for PortInfo:LinkSpeedExtEnabled parameter on the switch ports. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
3.4.1604 | Updated Description and Example | |
Example | switch (config) # show ib sm force-link-speed-ext | |
Related Commands | ib sm force-link-speed | |
Notes | Possible outputs:
|
show ib sm force-log-flush
show ib sm force-log-flush Displays if every log message generated forces the log to be flushed. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
3.4.1604 | Updated Description and Example | |
Example | switch (config) # show ib sm force-log-flush | |
Related Commands | ib sm force-log-flush | |
Notes |
show ib sm guid2lid-cache
show ib sm guid2lid-cache Displays whether or not the SM honors the cached GUID-to-LID mapping information. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm guid2lid-cache | |
Related Commands | ib sm guid2-lid-cache | |
Notes |
show ib sm honor-partitions
show ib sm honor-partitions Displays the partition enforcement settings in the subnet. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm honor-partitions | |
Related Commands | ib sm honor-partitions | |
Notes |
show ib sm hoq-lifetime
show ib sm hoq-lifetime Displays the maximum time a frame can wait at the head of a switch-to-switch port queue before it is dropped. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm hoq-lifetime | |
Related Commands | ib sm hoq-lifetime | |
Notes |
show ib sm ignore-other-sm
show ib sm ignore-other-sm Displays if the rules governing SM elections and attempt to manage the fabric on the node are ignored by the SM. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm ignore-other-sm | |
Related Commands | ib sm ignore-other-sm | |
Notes |
show ib sm ipv6-nsm
show ib sm ipv6-nsm Displays the consolidation of IPv6 Solicited Node Multicast (SNM) group join requests. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm ipv6-nsm | |
Related Commands | ib sm ipv6-nsm | |
Notes |
show ib sm lash
show ib sm lash {do-mesh-analysis | start-vl} Display “lash” routing method parameters. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm lash do-mesh-analysis | |
Related Commands | ib sm lash | |
Notes |
show ib sm leafhoq-lifetime
show ib sm leafhoq-lifetime Displays the maximum time a frame can wait at the head of a switch-to-CA_or_Router port queue before it is dropped. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm leafhoq-lifetime | |
Related Commands | ib sm leafhoq-lifetime | |
Notes |
show ib sm leafvl-stalls
show ib sm leafvl-stalls Displays the number of sequential frame drops that case a switch-to-CA_or_Router port to enter the VLStalled state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm leafvl-stalls | |
Related Commands | ib sm leafvl-stalls | |
Notes |
show ib sm lmc
show ib sm lmc Displays the number of sequential frame drops that case a switch-to-CA_or_Router port to enter the VLStalled state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm lmc | |
Related Commands | ib sm lmc | |
Notes |
show ib sm lmc-esp0
show ib sm lmc-esp0 Displays the number of sequential frame drops that case a switch-to-CA_or_Router port to enter the VLStalled state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm lmc-esp0 | |
Related Commands | ib sm lmc-esp0 | |
Notes |
show ib sm log
show ib sm log [continuous] [[not] [matching <reg-expression>]] Displays IB SM event logs. | ||
Syntax Description | continuous | Displays IB SM new event log messages as they arrive |
not | Displays IB SM new event logs that do not match a given regular expression | |
matching | Displays IB SM event log messages that match a given regular expression | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm log | |
Related Commands | show ib sm log-flags | |
Notes |
show ib sm log-flags
show ib sm log-flags Displays what type of messages the SM is logging. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm log-flags | |
Related Commands | ib sm log-flags | |
Notes |
show ib sm log-max-size
show ib sm log-max-size Displays the maximum size of the log file. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm log-max-size | |
Related Commands | ib sm log-max-size | |
Notes |
show ib sm max-op-vls
show ib sm max-op-vls Displays the maximum size of the log file. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm max-op-vls | |
Related Commands | ib sm max-op-vls | |
Notes |
show ib sm max-ports
show ib sm max-ports Displays the number of CA ports SM can manage. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm max-ports | |
Related Commands | ib sm max-ports | |
Notes |
show ib sm max-reply-time
show ib sm max-reply-time Displays the number of CA ports SM can manage. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm max-reply-time | |
Related Commands | ib sm max-reply-time | |
Notes |
show ib sm max-reverse-hops
show ib sm max-reverse-hops Displays max hops IO node to top switch. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm max-reverse-hops | |
Related Commands | ib sm max-reverse-hops | |
Notes |
show ib sm aguid-default-hop-limit
show ib sm aguid-default-hop-limit Displays max hops IO node to top switch. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm aguid-default-hop-limit | |
Related Commands | ib sm aguid-default-hop-limit | |
Notes |
show ib sm max-wire-smps
show ib sm max-wire-smps Displays the maximal number of MADs the SM will have outstanding at one time to count. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm max-wire-smps | |
Related Commands | ib sm max-wire-smps | |
Notes |
show ib sm max-wire-smps2
show ib sm max-wire-smps2 Displays maximal SM timeout based packets allowed to be outstanding. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm max-wire-smps2 | |
Related Commands | ib sm max-wire-smps2 | |
Notes |
show ib sm mkey-lease
show ib sm mkey-lease Displays MKey period in seconds. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm mkey-lease | |
Related Commands | ib sm mkey-lease | |
Notes |
show ib sm m-key
show ib sm m-key Displays the MKey used by the SM. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
3.6.2002 | Updated Example | |
Example | switch (config) # show ib sm m-key | |
Related Commands | ib sm m-key | |
Notes |
show ib sm mkey-lease
show ib sm mkey-lease Displays MKey lease period in seconds. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config) # show ib sm mkey-lease | |
Related Commands | ib sm mkey-lookup | |
Notes |
show ib sm mkey-lookup
show ib sm mkey-lookup Displays whether the SM looks in file cache for unknown note MKeys. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config) # show ib sm mkey-lookup | |
Related Commands | ib sm m-key | |
Notes |
show ib sm mkey-protect-level
show ib sm mkey-protect-level Displays MKey protection level. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config) # show ib sm mkey-protect-level | |
Related Commands | ib sm mkey-protect-level | |
Notes |
show ib sm msgfifo-timeout
show ib sm msgfifo-timeout Displays the elapsed time in milliseconds before a frame at the head of Subnet Agent queue causes an immediate BUSY state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm msgfifo-timeout | |
Related Commands | ib sm msgfifo-timeout | |
Notes |
show ib sm multicast
show ib sm multicast Displays whether the SM supports multicast on the fabric. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm multicast | |
Related Commands | ib sm multicast | |
Notes |
show ib sm no-client-rereg
show ib sm no-client-rereg Displays client re-registration admin state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm no-client-rereg | |
Related Commands | ib sm no-client-rereg | |
Notes |
show ib sm overrun-trigger
show ib sm overrun-trigger Displays count of local buffer overrun errors for Infiniband trap 130. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm overrun-trigger | |
Related Commands | ib sm overrun-trigger | |
Notes |
show ib sm packet-life-time
show ib sm packet-life-time Displays the maximum time a frame can live in a switch. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm packet-life-time | |
Related Commands | ib sm packet-life-time | |
Notes |
show ib sm phy-err-trigger
show ib sm phy-err-trigger Displays the number of local link integrity errors and the port’s SMA supports traps. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm phy-err-trigger | |
Related Commands | ib sm phy-err-trigger | |
Notes |
show ib sm polling-retries
show ib sm polling-retries Displays the number of consecutive times an active SM must fail to respond before it is declared dead. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm polling-retries | |
Related Commands | ib sm polling-retries | |
Notes |
show ib sm port-prof-switch
show ib sm port-prof-switch Displays whether or not the counting of adapters, routers, and switches through the links is being done. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm port-prof-switch | |
Related Commands | ib sm port-prof-switch | |
Notes |
show ib sm reassign-lids
show ib sm reassign-lids Displays the ability of the SM to reassign LIDs to nodes it finds already configured with a valid LID. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib sm reassign-lids | |
Related Commands | ib sm reassign-lids | |
Notes |
show ib sm root-guid
show ib sm root-guid Displays the configured root GUIDs for the SM. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm root-guid | |
Related Commands | ib sm routing-engine | |
Notes | The list of root GUIDs are relevant when IB SM is running on the switch, and the routing algorithm is up-down or fat-tree. |
show ib sm routing-engines
show ib sm routing-engines Displays an ordered list of routing engines. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm routing-engines | |
Related Commands | ib sm routing-engines | |
Notes |
show ib sm routing-info
show ib sm routing-info Displays current routing engine information. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm routing-info | |
Related Commands | ||
Notes |
show ib sm rtr-aguid-enable
show ib sm rtr-aguid-enable Displays GUID option configuration. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm rtr-aguid-enable | |
Related Commands | ib sm rtr-aguid-enable | |
Notes |
show ib sm rtr-pr-flow-label
show ib sm rtr-pr-flow-label Displays inter-subnet PathRecord FlowLabel. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm rtr-pr-flow-label | |
Related Commands | ib sm rtr-pr-flow-label | |
Notes | “0” signifies that inter-subnet PathRecord FlowLabel is disabled |
show ib sm rtr-pr-mtu
show ib sm rtr-pr-mtu Displays inter-subnet PathRecord MTU. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm rtr-pr-mtu | |
Related Commands | ib sm rtr-pr-mtu | |
Notes |
show ib sm rtr-pr-rate
show ib sm rtr-pr-rate Displays inter-subnet PR rate. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm rtr-pr-rate | |
Related Commands | ib sm rtr-pr-rate | |
Notes |
show ib sm rtr-pr-sl
show ib sm rtr-pr-sl Displays inter-subnet PathRecord service level. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm rtr-pr-sl | |
Related Commands | ib sm rtr-pr-sl | |
Notes |
show ib sm sa-key
show ib sm sa-key Displays the SM sa-key value used by SA to qualify that a query is “trusted”. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sa-key | |
Related Commands | ib sm rtr-pr-sl | |
Notes |
show ib sm single-thread
show ib sm single-thread Displays if the SM uses a single thread to service all requests. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm single-thread | |
Related Commands | ib sm single-thread | |
Notes |
show ib sm sm-inactive
show ib sm sm-inactive Displays whether or not the SM starts in “inactive” rather than “init” SM state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sm-inactive | |
Related Commands | ib sm sm-inactive | |
Notes |
show ib sm sm-key
show ib sm sm-key Displays the SM 64-bit SM_Key. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.63.1.0000 | |
Example | switch (config)# show ib sm sm-key | |
Related Commands | ib sm sm-key | |
Notes |
show ib sm sm-priority
show ib sm sm-priority Displays the importance of this SM compared to other SMs on the fabric. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sm-priority | |
Related Commands | ib sm sm-priority | |
Notes | If 2 or more active SMs have the same highest priority, the one with the lowest port GUID will manage the fabric. |
show ib sm sm-sl
show ib sm sm-sl Displays SL used for SM/SA communication. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sm-sl | |
Related Commands | ib sm sm-sl | |
Notes |
show ib sm sminfo-poll-time
show ib sm sminfo-poll-time Displays the timeout in milliseconds between two polls of an active SM. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sminfo-poll-time | |
Related Commands | ib sm sminfo-poll-time | |
Notes |
show ib sm subnet-prefix
show ib sm subnet-prefix Displays the SM “Subnet Prefix” used to create scope qualifiers for all elements managed by the SM. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm subnet-prefix | |
Related Commands | ib sm subnet-prefix | |
Notes |
show ib sm subnet-prefix-override
show ib sm subnet-prefix-override Displays whether IB Router subnet prefix checking is enabled or disabled. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm subnet-prefix-override | |
Related Commands | ib sm subnet-prefix-override | |
Notes |
show ib sm subnet-timeout
show ib sm subnet-timeout Displays the global per-port subnet timeout value (PortInfo:SubnetTimeOut). This value also controls the maximum trap frequency in which no traps are allowed to be sent faster than the subnet_timeout value. The time is 4.096 uS * 2*time. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm subnet-timeout | |
Related Commands | ib sm subnet-timeout | |
Notes |
show ib sm sweep-interval
show ib sm sweep-interval Displays the time in seconds between subnet sweeps. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sweep-interval | |
Related Commands | ib sm sweep-interval | |
Notes |
show ib sm sweep-on-trap
show ib sm sweep-on-trap Displays whether or not a heavy sweep is initiated by the TRAP received by the SM. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm sweep-on-trap | |
Related Commands | ib sm sweep-on-trap | |
Notes |
show ib sm transaction-retries
show ib sm transaction-retries Displays maximum retries before failing a transaction. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm transaction-retries | |
Related Commands | ib sm transaction-retries | |
Notes |
show ib sm use-heavy-sweeps
show ib sm use-heavy-sweeps Displays maximum retries before failing a transaction. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm use-heavy-sweeps | |
Related Commands | ib sm use-heavy-sweeps | |
Notes |
show ib sm use-ucast-cache
show ib sm use-ucast-cache Displays maximum retries before failing a transaction. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm use-ucast-cache | |
Related Commands | ib sm use-ucast-cache | |
Notes |
show ib sm version
show ib sm version Displays the OpenSM version currently running. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.2.3000 | |
Example | switch (config)# show ib sm version | |
Related Commands | ||
Notes |
show ib sm virt-default-hop-limit
show ib sm virt-default-hop-limit Displays the open SM version that is currently running. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm virt-default-hop-limit | |
Related Commands | ib sm virt-default-hop-limit | |
Notes |
show ib sm virt-max-ports-in-process
show ib sm virt-max-ports-in-process Displays the maximum number of ports to be processed simultaneously. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.2002 | |
Example | switch (config)# show ib sm virt-max-ports-in-process | |
Related Commands | ib sm virt-max-ports-in-process | |
Notes |
show ib sm vl-stalls
show ib sm use-vl-stalls Displays the number of sequential frame drops that cause a switch-to-switch port to enter the VLStalled state. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config)# show ib sm vl-stalls | |
Related Commands | ib sm vl-stalls | |
Notes |
ib partition
ib partition <partition-name> [pkey <pkey number>] Enters the context of the partition specified. | ||
Syntax Description | partition-name | Name of partition context to be entered |
pkey | Creates a partition and enters a new configuration mode | |
force | Forces configuration | |
Default | Default partition is available (PKEY 0x7fff) | |
Configuration Mode | config | |
History | 3.2.0500 | |
3.6.8008 | ||
Example | switch (config) # ib partition my-partition | |
Related Commands | ||
Notes |
pkey
pkey <number> [force] Specifies PKEY number for this partition. | ||
Syntax Description | number | Range: 0x001-0x7fff |
force | Forces configuration | |
Default | N/A | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.5.1000 | Added “force” parameter | |
Example | switch (config partition my-partition) # pkey 0x7777 | |
Related Commands | ||
Notes | PKEY must be unique |
defmember
defmember <type> [force] Sets the default membership for port GUID list. | ||
Syntax Description | type | Default membership for GUIDs in this partition:
|
force | Forces configuration | |
Default | limited | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.4.1100 | Added “both” option | |
3.5.1000 | Added “force” parameter | |
Example | switch (config ib partition my-partition) # defmember full | |
Related Commands | ib sm allow-both-pkeys | |
Notes | This parameter can be overwritten for specific GUID, using the “member” command. |
member
member {<guid> | all | all-cas | all-routers | all-switches | all-vcas | self } [type <member-type>] [force] no member {<guid> | all | all-cas | all-routers | all-switches | all-vcas | self } [type] [force] Adds static members to partition. | ||
Syntax Description | guid | The GUID number |
all | Can be used for all GUIDs in the fabric | |
self | Can be used for the the switch GUID | |
all-cas | Adds all GUIDs that belong to CA ports in the fabric | |
all-routers | Adds all GUIDS that belong to routers in the fabric | |
all-switches | Adds all GUIDS that belong to switched in the fabric | |
all-vcas | Adds all GUIDS that belong to virtual CA posts in the fabric | |
member-type | Default membership for GUIDs in this partition:
| |
force | Forces configuration (only relevant to the default partition) | |
Default | N/A | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.4.1100 | Added “both” parameter | |
3.5.1000 | Added “force” parameter | |
3.8.2100 | Added "all-cas," "all-routers," all-switches," and "all-vcas" parameters | |
Example | switch (config ib partition my-partition) # member all | |
Related Commands | ib partition | |
Notes |
ipoib
ipoib [force] Enables this partition to use IPoIB. As a result IPoIB multicast group will be created. | ||
Syntax Description | force | Forces configuration |
Default | no IPoIB | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.5.1000 | Added “force” parameter | |
3.6.8008 | Added “force” parameter to no form | |
Example | switch (config ib partition my-partition) # ipoib | |
Related Commands | ib partition | |
Notes | The commands “rate”, “mtu”, “sl” and “scope” can be used only when the IPoIB parameter is enabled. |
mtu
mtu <256, 512, 1K, 2K,4K> [force] Specifies MTU for this IPoIB multicast group. | ||
Syntax Description | force | Forces configuration |
Default | 2K | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.5.1000 | Added “force” parameter | |
Example | switch (config ib partition my-partition) # mtu 4K | |
Related Commands | ipoib | |
Notes | IPoIB parameter on the partitions must be enabled in order to use this parameter |
rate
rate <rate> [force] Specifies rate for this IPoIB multicast group. | ||
Syntax Description | rate |
|
Default | 10Gb/s | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.4.1100 | Updated rate Syntax Description | |
3.5.1000 | Added “force” parameter | |
Example | switch (config partition my-partition) # rate 20 | |
Related Commands | ipoib | |
Notes | Ports that do not support the IPoIB rate are not added to the partition |
scope
scope <type> [force] Specifies scope for this IPoIB multicast group. | ||
Syntax Description | type |
|
force | Forces configuration | |
Default | link-local | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.5.1000 | Added “force” parameter | |
Example | switch (config partition my-partition) # scope global | |
Related Commands | ipoib | |
Notes | IPoIB parameter on the partitions must be enabled in order to use this parameter. |
sl
sl <0-14, “default”> [force] Specifies SL (Service Level - QoS) for this IPoIB multicast group. | ||
Syntax Description | force | Forces configuration |
Default | Default (0) | |
Configuration Mode | config partition | |
History | 3.2.0500 | |
3.5.1000 | Added “force” parameter | |
Example | switch (config partition my-partition) # sl 7 | |
Related Commands | ipoib | |
Notes | IPoIB parameter on the partitions must be enabled in order to use this parameter. |
show ib partition
show ib partition [<partition-name> [member [<member-name>]]] Displays partition info, with optional to filters. | ||
Syntax Description | partition-name | Filters the output per partition name |
member <member-name> | Filters the output by a specific member | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.2.0500 | |
3.6.8008 | Updated Example and note | |
Example | switch (config) # show ib partition Default Default PKey = 0x7FFF ipoib = yes members GUID='ALL' member='full' | |
Related Commands | ||
Notes | If bulk update mode is enabled, this command notifies the user that these changes may not have been applied yet. |
ib baseqos high-limit
ib baseqos <port-type> high-limit <count> Sets the high-limit value for the indicated port type. Thus the system will send at least 4096 * <count> bytes from the high priority list before sending any from the low priority list. | ||
Syntax Description | port-type |
|
high-limit | Possible values are: -1...255
| |
Default | -1 (default SM high-limit) | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib baseqos ca high-limit 255 | |
Related Commands | show ib baseqos | |
Notes | A high-limit value of 255 means unlimited, and that makes it possible to starve the low priority list. |
ib baseqos max-vls
ib baseqos <port-type> max-vls <value> Configures the maximum number of VLs for the indicated port type. | ||
Syntax Description | port-type |
|
value | Range: 1-15 | |
Default | 15 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib baseqos ca max-vls 15 | |
Related Commands | show ib baseqos | |
Notes |
ib baseqos sl2vl
ib baseqos <port-type> sl2vl {sl0 | sl0 sl1 | sl0 sl1 sl2 |...} Sets a list of up to 16 entries that map the SL entry to an appropriate VL. | ||
Syntax Description | port-type |
|
sl[i] | A single vector (1 ... 16 elements), the command line vector determine the SL [0...15] that is mapped to the specified VL [0...15]. | |
Default | The default mapping is: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,7 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # show ib baseqos ca sl2vl | |
Related Commands | show ib baseqos | |
Notes | Any missing SLs will be mapped to VL15. |
ib baseqos vlarb-high
ib baseqos <port-type> vlarb-high {VW1 | VW1 VW2 | ...} Sets up to 15 VL to Weight mapping pairs for high priority processing. | ||
Syntax Description | port-type |
|
VW[i] | There are two possible options for this parameter:
| |
Default | The default mapping is: 0:4,1:0,2:0,3:0,4:0,5:0,6:0,7:0,8:0,9:0,10:0,11:0,12:0,13:0,14:0 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # show ib baseqos ca vlarb-high | |
Related Commands | show ib baseqos | |
Notes |
|
ib baseqos vlarb-low
ib baseqos <port-type> vlarb-low {VW1 | VW1 VW2 | ...} Sets up to 15 VL to Weight mapping pairs for low priority processing. | ||
Syntax Description | port-type |
|
VW[i] | There are two possible options for this parameter:
| |
Default | The default mapping is: 0:0,1:4,2:4,3:4,4:4,5:4,6:4,7:4,8:4,9:4,10:4,11:4,12:4,13:4,14:4 | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib baseqos sw0 vlarb-low 1:1 | |
Related Commands | show ib baseqos | |
Notes | You may have multiple entries with the same VL on this list. |
ib baseqos reset-config
ib baseqos reset-config Resets all basic QoS configuration options to defaults. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib baseqos reset-config | |
Related Commands | ||
Notes |
show ib baseqos
show ib baseqos <port-type> <baseqos-parameters> Displays the base IB QoS configuration. | ||
Syntax Description | port-type |
|
baseqos-parameters | Possible values are:
| |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib baseqos ca high-limit | |
Related Commands | ||
Notes |
ib qos
ib qos Enables advanced QoS management on this node. | ||
Syntax Description | N/A | |
Default | Advance QoS is disabled | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # show ib qos | |
Related Commands | show ib qos | |
Notes |
ib qos level
ib qos level {<name> | default} {mtu-limit <mtu> | packet-life <time> | pkey <number> | rate-limit <rate-value> | sl <sl-value>| use <description>} Specifies a QoS level <name> or “default” parameters. | ||
Syntax Description | <name> | default | Specify a name for this qos group, or use the “default” for the default qos parameters |
mtu-limit <mtu> | MTU in bytes | |
packet-life <time> | Time a packet can wait in switch egress queue before being dropped. The bytes from 4 microsecond up to 2 seconds or infinite. | |
pkey <number> | PKEY value: ranges between -1 and 32767 (hex 0x7fff) | |
rate-limit <rate-value> | Manages rate limits for QoS Policy levels | |
sl <sl-value> | Manages service level for QoS Policy levels | |
use <description> | Specify usage description for this QoS level | |
Default |
| |
Configuration Mode | config | |
History | 3.1.0000 | |
3.4.1100 | Updated description of “rate-limit” parameter | |
Example | switch (config) # show ib qos my-qos-group | |
Related Commands | show ib qos | |
Notes |
ib qos match-rule
ib qos match-rule <rule-index> {{destination | source} <string> | {pkey | qos-class | service-id} <index> {first | last} <value>} | qos-level-name <name> | use <description>} Manages QoS Policy match rules. | ||
Syntax Description | rule-index | Index of this match-rule |
destination | source <string> | Manages destination or source for QoS Policy match rules | |
pkey | qos-class | service-id <index> | Manages values for QoS Policy match rules | |
{first | last} <value> | First or last value range (per PKEY / qos-class of service ID | |
qos-level-name <name> | Name for the QoS level | |
use <description> | Specify usage description for this QoS level | |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # show ib qos match-rule 10 | |
Related Commands | show ib qos | |
Notes |
ib qos port-group
ib qos port-group <name> {node-type <index> type <node-type> | partition <name>| pkey <number> | port-guid <index> {first | last} <value> | port-name <index> name <name-value>| use <description>} Manages QoS Policy port groups. | ||
Syntax Description | <name> | Port group name |
node-type <index> | Node type index | |
type <node-type> | A node type for this port group | |
partition <name> | A Partition name | |
pkey <number> | A PKEY number | |
port-guid <index> {first | last} <value> | Port-guid range | |
port-name <index> name <name-value> | Port index name | |
use <description> | Specify usage description for this QoS level | |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config)# show ib qos port-group my-group | |
Related Commands | show ib qos | |
Notes |
ib qos ulp any
ib qos ulp any {pkey | service-id | target-port-guid <index> {first | last | sl} <value> | sl <sl-vlaue>} Configures ULP any attributes. | ||
Syntax Description | pkey <index> | Manages ULP default PKEY assignment |
service-id <index> | Manages default ULP Service ID match rule | |
target-port-quid <index> | Manages ULP default target port GUID rule | |
first | last | sl <value> |
| |
sl <sl-value> | Sets default SL | |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib qos ulp any sl 2 | |
Related Commands | show ib qos | |
Notes |
ib qos ulp ipoib
ib qos ulp ipoib {default sl <sl-value>| pkey <index> {first | last | sl} <value> } Manages ULP IPoIB settings. | ||
Syntax Description | default sl <sl-value> | Sets the default SL |
pkey <index> | Manages ULP default PKEY assignment | |
first | last | sl <value> |
| |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib qos ulp ipoib default sl 5 | |
Related Commands | show ib qos | |
Notes |
ib qos ulp
ib qos ulp <protocol-type> {default sl <sl-value> | port-num< index> <first | last | sl> <value>} Configures ULP IScsi Extensions for RDMA, Reliable Datagram Sockets or Sockets Direct Protocol attributes. | ||
Syntax Description | protocol-type | iser—iSCSI extensions for RDMA ( iSER) rds—reliable datagram sockets ( RDS) sdp—sockets direct protocol (SDP) |
default sl <sl-value> | Sets the default SL | |
port-num< index> | Port number index | |
first | last | sl |
| |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib qos ulp iser default sl 2 | |
Related Commands | show ib qos | |
Notes |
ib qos ulp srp
ib qos ulp srp target-port-guid <index> <first | last | sl> <value> Configures Scsi Rdma Protocol attributes. | ||
Syntax Description | target-port-guid <index> | The index of the target port GUID |
first | last | sl |
| |
Default | N/A | |
Configuration Mode | config | |
History | 3.1.0000 | |
Example | switch (config) # ib qos ulp srp target-port-guid 1 sl 2 | |
Related Commands | show ib qos | |
Notes |
show ib qos
show ib qos [level | match-rule | port-group | ulp] Displays InfiniBand QoS configurations | ||
Syntax Description | level | Displays QoS level configurations |
match-rule | Displays QoS match-rule configurations | |
port-group | Displays QoS port-group configurations | |
ulp | Displays QoS ulp configurations | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.1.0000 | |
Example | switch (config) # show ib qos level my-qos-level | |
Related Commands | ||
Notes |
ib sm scatter-ports
ib sm scatter-ports <seed> Activates scatter ports and sets seed for random number generation. | ||
Syntax Description | seed | Integer between 0-4294967295 |
Default | Disabled | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm scatter-ports 123 | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
show ib sm scatter-ports
show ib sm scatter-ports Displays scatter port seed. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.8008 | |
Example |
| |
Related Commands | ib sm scatter-ports | |
Notes |
ib sm guid-routing-order add
ib sm guid-routing-order add <guid> [position <pos>] Adds a new GUID to routing order list. | ||
Syntax Description | guid | GUID to add |
position | A position for the new GUID may be specified | |
Default | If no position is specified, the new GUID is added to the end of the list | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm guid-routing-order add E4:1D:2D:03:00:3D:5E:87 position 6 | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
ib sm guid-routing-order delete
ib sm guid-routing-order delete {<guid> | position <pos>} Deletes a guid from routing order list. The guid can be chosen by its guid or by its position on guid routing order list. | ||
Syntax Description | guid | GUID to delete |
position | Deletes a GUID by specifying position number | |
Default | N/A | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm guid-routing-order delete position 3 | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
ib sm guid-routing-order move
ib sm guid-routing-order move <guid> to-position <pos> Moves a GUID in the list to a specified position. | ||
Syntax Description | guid | GUID to move |
position | A position for the new GUID may be specified | |
Default | N/A | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm guid-routing-order move E4:1D:2D:03:00:3D:5E:91 to-position 2 | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
ib sm guid-routing-order move-down
ib sm guid-routing-order move-down <guid> Moves a GUID position down in the GUID routing order list. | ||
Syntax Description | guid | GUID to move |
Default | N/A | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm guid-routing-order move-down E4:1D:2D:03:00:3D:5E:91 | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
ib sm guid-routing-order move-up
ib sm guid-routing-order move-up <guid> Moves a GUID position up in the GUID routing order list. | ||
Syntax Description | guid | GUID to move |
Default | N/A | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm guid-routing-order move-up E4:1D:2D:03:00:3D:5E:91 | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
no ib sm guid-routing-order
no ib sm guid-routing-order Disables the GUID routing order feature and cleans GUID routing order list. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # no ib sm guid-routing-order | |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
ib sm guid-routing-order-no-scatter
ib sm guid-routing-order-no-scatter Enables randomization for destinations mentioned in GUID order list. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm guid-routing-order-no-scatter | |
Related Commands | ib sm guid-routing-order * | |
Notes | If scatter ports (randomization of the output port) is set to anything but zero, guid-routing-order-no-scatter defines whether or not randomization should be applied to the destination GUIDs mentioned in the GUID routing order list |
show ib sm guid-routing-order
show ib sm guid-routing-order Displays current GUID routing order list. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.8008 | |
Example |
| |
Related Commands | ib sm guid-routing-order-no-scatter | |
Notes |
show ib sm guid-routing-order-no-scatter
show ib sm guid-routing-order-no-scatter Displays the status of the GUID-routing-order-no-scatter feature | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.8008 | |
Example |
| |
Related Commands | ib sm guid-routing-order * | |
Notes |
ib sm bulk-update enable
ib sm bulk-update enable Enables bulk update mode. | ||
Syntax Description | N/A | |
Default | Disabled | |
Configuration Mode | config | |
History | 3.6.8008 | |
Example | switch (config) # ib sm bulk-update enable | |
Related Commands | show ib partition | |
Notes |
show ib sm bulk-update
show ib sm bulk-update Displays the status of bulk-update mode. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.6.8008 | |
Example |
| |
Related Commands | ib sm bulk-update enable | |
Notes |
ibdiagnet
ibdiagnet [parameters] | ||
Syntax Description | parameters | Ibdiagnet native parameters |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.9.3100 | |
Example | switch (config) # ibdiagnet | |
Related Commands | show ibdiagnet | |
Notes | To know the optional parameters, run ibdiagnet -h. |
show ibdiagnet
show ibdiagnet Show output from latest call to ibdiagnet | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.9.3100 | |
Example | switch (config) # show ibdiagnet | |
Related Commands | ibdiagnet | |
Notes |
file ibdiagnet upload
file ibdiagnet upload <file name> <upload_url> Upload ibdiagnet archive of output files (from latest call to ibdiagnet) to a remote host. | ||
Syntax Description | N/A | |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.9.3100 | |
Example | switch (config) # file ibdiagnet upload ibdiagnet_output.gz scp:// username:password@192.168.10.125/var/www/html/<image_name> | |
Related Commands | Ibdiagnet | |
Notes |
file ibdiagnet delete
file ibdiagnet delete <file name> Deletes the specified ibdiagnet archive file. | ||
Syntax Description | <file name> | File name |
Default | N/A | |
Configuration Mode | Any command mode | |
History | 3.9.3100 | |
Example | switch (config) # file ibdiagnet delete ibdiagnet_output.gz | |
Related Commands | file ibdiagnet upload | |
Notes |