NVIDIA Docs Hub NVIDIA Networking Networking Software Switch Software NVIDIA MLNX-OS User Manual v3.10.4100 (LTS) Network Management Interface Commands

v8.2.2200

	snmp-server auto-refresh {enable \| interval <time>} no snmp-server auto-refresh enable Configures SNMPD refresh settings. The no form of the command disables SNMPD refresh mechanism.
Syntax Description	enable	Enables SNMPD refresh mechanism.
	interval	Sets SNMPD refresh interval.
	time	Range: 20-500 seconds
Default	Enabled Interval—60 seconds
Configuration Mode	config
History	3.2.3000 3.4.1100: Added “time” parameter and updated notes
Example	switch (config) # snmp-server auto-refresh interval 120
Related Commands	show snmp
Notes	When configuring an interval lower than 60 seconds, the following warning message appears asking for confirmation: “Warning: this configuration may increase CPU utilization, Type 'YES' to confirm: YES When disabling SNMP auto-refresh, information is retrieved no more than once every 60 seconds just like SNMP tables that do not have an auto-refresh mechanism

snmp-server cache enable

	snmp-server cache enable no snmp-server cache enable Enables SNMP cache if auto-refresh is disabled. The no form of the command disables SNMP cache if auto-refresh is disabled.
Syntax Description	N/A
Default	Enabled
Configuration Mode	config
History	3.7.0000
Example	switch (config) # snmp-server cache enable
Related Commands	show snmp auto-refresh snmp-server auto-refresh enable
Notes	If SNMP auto-refresh is enabled, the value of cache is meaningless If SNMP cache is disabled, every SNMP request gets updated data

snmp-server community

	snmp-server community <community> [ro \| rw] no snmp-server community <community> Sets a community name for either read-only or read-write SNMP requests. The no form of the command sets the community string to default.
Syntax Description	community	Community name
	ro	Sets the read-only community string
	rw	Sets the read-write community string
Default	Read-only community: “public” Read-write community: “”
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server community private rw
Related Commands	show snmp
Notes	If neither the “ro” or the “rw” parameters are specified, the read-only community is set as the default community If the read-only community is specified, only queries can be performed If the read-write community is specified, both queries and sets can be performed

snmp-server contact

	snmp-server contact <contact-name> no snmp-server contact Sets a value for the sysContact variable in MIB-II. The no form of the command resets the parameter to its default value.
Syntax Description	contact-name	Contact name
Default	“”
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server contact my-name
Related Commands	show snmp
Notes

snmp-server enable

	snmp-server enable no snmp-server enable Enables SNMP-related functionality (SNMP engine, and traps). The no form of the command disables the SNMP server.
Syntax Description	N/A
Default	SNMP is enabled by default
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server enable
Related Commands	show snmp
Notes

snmp-server engineID reset

	snmp-server engineID reset Resets the SNMPv3 engine ID to be node unique.
Syntax Description	N/A
Default	Default engineID is unchanged
Configuration Mode	config
History	3.6.6102
Example	switch (config) # snmp-server engienID reset
Related Commands	show snmp engineID
Notes	Changing system profile or performing “reset factory...” causes the engine ID to change to the new node-unique one.

snmp-server enable mult-communities

	snmp-server enable mult-communities no snmp-server enable mult-communities Enables multiple communities to be configured. The no form of the command disables multiple communities to be configured.
Syntax Description	N/A
Default	SNMP server multi-communities are disabled by default
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server enable mult-communities
Related Commands	show snmp
Notes

snmp-server enable notify

	snmp-server enable notify no snmp-server enable notify Enables sending of SNMP traps and informs from this system. The no form of the command disables sending of SNMP traps and informs from this system.
Syntax Description	N/A
Default	SNMP notifies are enabled by default
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server enable notify
Related Commands	show snmp
Notes	SNMP traps are only sent if there are trap sinks configured with the “snmp-server host...” command, and if these trap sinks are themselves enabled.

snmp-server enable set-permission

	snmp-server enable set-permission <MIB-name> no snmp-server enable set-permission <MIB-name> Allows SNMP SET requests for items in a specified MIB. The no form of the command disallows SNMP SET requests for items in a specified MIB.
Syntax Description	N/A
Default	SNMP MIBs are all given permission for SET requests by default
Configuration Mode	config
History	3.6.3004
Example	switch (config) # snmp-server enable set-permission MELLANOX-SW-UPDATE
Related Commands	show snmp set-permission
Notes

snmp-server host disable

	snmp-server host <ip-address> disable no snmp-server host <ip-address> [disable] Temporarily disables sending of all notifications to this host. The no form of the commands resumes sending of all notifications to this host.
Syntax Description	ip-address	IPv4 or IPv6 address
Default	N/A
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server host 10.10.10.10 disable
Related Commands	show snmp snmp-server enable
Notes

snmp-server host informs

	snmp-server host <ip-address> informs [<community> \| port <port> \| version 2c \| version 3 {engineID <engineID> \| user <name> {auth <hash-type> <auth- password> [priv <privacy-type> [<priv-password>]] \| encrypted auth ... \| prompt auth ...}}] no snmp-server host <ip-address> informs port Send SNMP v2c informs to this host with the default trap community. The no form of the commands removes a host from which SNMP traps should be sent.
Syntax Description
	IP address	IPv4 or IPv6 address.
	community	Specifies trap community string.
	port	Overrides default UDP port for this trap sink.
	version	Specifies the SNMP version of traps to send to this host.
	engineID	Specifies engine ID of this inform sink.
	user	Specifies username for this inform sink.
	auth	Configures SNMPv3 security parameters, specifying passwords in plaintext on the command line (passwords are always stored encrypted).
	hash-type	MD5 SHA
	auth-password	Plaintext password to use for authentication. If “priv” is not specified the default privacy algorithm is used with the same privacy password as that specified for authentication.
	priv	Specifies SNMPv3 privacy settings for this user.
	privacy-type	aes-128—uses AES-128 encryption for privacy des—uses DES encryption for privacy
	priv-password	Plaintext password to use for privacy. If not specified, then auth-password is used.
	encrypted	Configure SNMPv3 security parameters specifying passwords in encrypted form.
	prompt	Configure SNMPv3 security parameters specifying passwords securely in follow-up prompts rather than on the command line.
Default	community—public UDP port—162 version—3
Configuration Mode	config
History	3.2.1050
Example	switch (config) # snmp-server host 1.1.1.1 informs version 3 engineID 0x800041da04643265363932653432303135 user test auth md5 password priv aes-128 password
Related Commands	show snmp snmp-server enable snmp-server host informs version 3
Notes

snmp-server host traps

	snmp-server host <ip-address> traps [<community> \| port <port> \| version {1 \| 2c} \| version 3 {user <name> {auth <hash-type> <auth-password> [priv <privacy-type> [<priv-password>]] \| encrypted auth ... \| prompt auth ...}}] no snmp-server host <ip-address> traps port Send SNMP v2c traps to this host with the default trap community. The no form of the commands removes a host from which SNMP traps should be sent.
Syntax Description
	ip-address	IPv4 or IPv6 address.
	community	Specifies trap community string.
	port	Overrides default UDP port for this trap sink.
	version	Specifies the SNMP version of traps to send to this host.
	user	Specifies username for this inform sink.
	auth	Configures SNMPv3 security parameters, specifying passwords in plaintext on the command line (passwords are always stored encrypted).
	hash-type	MD5 SHA
	auth-password	Plaintext password to use for authentication. If “priv” is not specified the default privacy algorithm is used with the same privacy password as that specified for authentication.
	priv	Specifies SNMPv3 privacy settings for this user.
	privacy-type	aes-128—uses AES-128 encryption for privacy des—uses DES encryption for privacy
	priv-password	Plaintext password to use for privacy. If not specified, then auth-password is used.
	encrypted	Configure SNMPv3 security parameters, specifying passwords in encrypted form.
	prompt	Configure SNMPv3 security parameters, specifying passwords securely in follow-up prompts, rather than on the command line.

Default	community—public UDP port—162 version—3
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server host 1.1.1.1 informs version 3 user test auth md5 password priv aes-128 password
Related Commands	show snmp snmp-server enable snmp-server host informs version 3
Notes

snmp-server listen

	snmp-server listen {enable \| interface <ifName>} no snmp-server listen {enable \| interface <ifName>} Configures SNMP server interface access restrictions. The no form of the command disables the listen interface restricted list for SNMP server.
Syntax Description	enable	Enables SNMP interface restrictions on access to this system
Syntax Description	ifName	Adds an interface to the “listen” list for SNMP server. For example: “mgmt0”, “mgmt1”
Default	N/A
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp listen enable
Related Commands	show snmp
Notes	If enabled, and if at least one of the interfaces listed is eligible to be a listen interface, then SNMP requests will only be accepted on those interfaces. Otherwise, SNMP requests are accepted on any interface.

snmp-server notify

	snmp-server notify {community <community> \| event <event name> \| port <port> \| send-test} no snmp-server notify {community \| event <event name> \| port} Configures SNMP notifications (traps and informs). The no form of the commands negate the SNMP notifications.
Syntax Description	community	Sets the default community for traps sent to hosts which do not have a custom community string set
	event	Specifies which events will be sent as traps
	port	Sets the default port to which traps are sent
	send-test	Sends a test trap
Default	All informs and traps are enabled community—public UDP port—162
Configuration Mode	config
History	3.1.0000 3.2.1050: Changed traps to notify
Example	switch (config) # snmp-server community public
Related Commands	show snmp show snmp events
Notes	This setting is only meaningful if traps are enabled, though the list of hosts may still be edited if traps are disabled Refer to Mellanox MIB file for the list of supported traps

snmp-server port

	snmp-server port <port> no snmp-server port Sets the UDP listening port for the SNMP agent. The no form of the command resets the parameter to its default value.
Syntax Description	port	UDP port
Default	161
Configuration Mode	config
History	3.1.0000
Example	switch (config) # snmp-server port 1000
Related Commands	show snmp
Notes

snmp-server user

	snmp-server user {admin \| <username>} v3 {[encrypted] auth <hash-type> <password> [priv <privacy-type> [<password>]] \| capability <cap> \| enable <sets> \| prompt auth <hash-type> [priv <privacy-type>] \| require-privacy} no snmp-server user {admin \| <username> } v3 {[encrypted] auth <hash-type> <password> [priv <privacy-type> [<password>]] \| capability <cap> \| enable <sets> \| prompt auth <hash-type> [priv <privacy-type>]} Specifies an existing username, or a new one to be added. The no form of the command disables access via SNMP v3 for the specified user.
Syntax Description	v3	Configures SNMPv3 users.
	auth	Configures SNMPv3 security parameters, specifying passwords in plaintext on the command line (note: passwords are always stored encrypted). Available hash-type options are: <md5\|sha\|sha224\|sha256\|sha384\|sha512>.
	capability	Sets capability level for SET requests.
	enable	Enables SNMPv3 access for this user.
	encrypted	Configures SNMPv3 security parameters, specifying passwords in encrypted form.
	prompt	Configures SNMPv3 security parameters, specifying passwords securely in follow-up prompts, rather than on the command line.
	require-privacy	Requires privacy (encryption) for requests from this user.
	priv	Configures SNMPv3 security parameters, specifying which protocol to use for traffic encryption. Available priv-type options: <des\|3des\|aes-128\|aes-192\|aes-256>.
Default	No SNMP v3 users defined
Configuration Mode	config
History	3.1.0000 3.7.0000 3.8.1000: Syntax updated
Example	switch (config) # snmp-server user admin v3 enable
Related Commands	show snmp user
Notes	The username chosen here may be anything that is valid as a local UNIX username (alphanumeric, plus '-', '_', and '.'), but these usernames are unrelated to, and independent of, local user accounts. That is, they need not have the same capability level as a local user account of the same name. Note that these usernames should not be longer than 31 characters, or they will not work. The hash algorithm specified is used both to create digests of the authentication and privacy passwords for storage in configuration, and also in HMAC form for the authentication protocol itself There are three variants of the command, which branch out after the “v3” keyword. If “auth” is used next, the passwords are specified in plaintext on the command line. If “encrypted” is used next, the passwords are specified encrypted (hashed) on the command line. If “prompt-pass” is used, the passwords are not specified on the command line the user is prompted for them when the command is executing. If “priv” is not specified, only the auth password is prompted for. If “priv” is specified, the privacy password is prompted for; entering an empty string for this prompt will result in using the same password specified for authentication. AES privacy type encryption using the newest algorithm, which means we use aes-blumenthal. For more information see http://www.snmp.com/eso/esoConsortiumMIB.txt. No more than 30 SNMPv3 users are allowed in the database

show snmp

	show snmp [events \| host] Displays SNMP-server configuration and status.
Syntax Description	events	SNMP events
Syntax Description	host	List of notification sinks
Default	N/A
Configuration Mode	Any command mode
History	3.1.0000 3.6.8008—Updated example
Example	switch (config) # show snmp SNMP enabled : no SNMP port : 161 System contact : Test System location: Boston Read-only communities: public Read-write communities: good Interface listen enabled: yes Listen Interfaces: Interface: mgmt0
Related Commands	show snmp
Notes

show snmp auto-refresh

	show snmp auto-refresh Displays SNMPD refresh mechanism status.
Syntax Description	N/A
Default	N/A
Configuration Mode	Any command mode
History	3.1.0000 3.6.6000: Updated example 3.7.0000: Updated example
Example	switch (config) # show snmp auto-refresh SNMP auto refresh: Auto-refresh enabled: yes Refresh interval (sec): 60 Cache enabled: yes Auto-Refreshed tables: ifTable ifXTable mellanoxIfVPITable
Related Commands	snmp-server auto-refresh
Notes

show snmp engineID

	show snmp engineID Displays SNMPv3 engine ID key.
Syntax Description	N/A
Default	N/A
Configuration Mode	Any command mode
History	3.6.6102
Example	switch (config) # show snmp engineID Local SNMP engineID: 0x80004f4db1dd435e80accf4a4d4d3031
Related Commands	snmp-server engineID
Notes

show snmp set-permission

	show snmp set-permission Displays SNMP SET permission settings.
Syntax Description	N/A
Default	N/A
Configuration Mode	Any command mode
History	3.6.3004
Example	switch (config) # show snmp set-permission --------------------------------------------- MIB Name Set Enable --------------------------------------------- MELLANOX-CONFIG-DB-MIB yes MELLANOX-EFM-MIB yes MELLANOX-POWER-CYCLE yes MELLANOX-SW-UPDATE no RFC1213-MIB no
Related Commands	snmp-server enable set-permission
Notes

show snmp user

	show snmp user Displays SNMP user information.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	3.1.0000 3.6.8008: Updated example
Example	switch (config) # show snmp user User name: Hendrix Enabled overall: yes Authentication type: sha Privacy type: des Authentication password: (set) Privacy password: (set) Require privacy: yes SET access: Enabled: yes Capability level: admin
Related Commands	show snmp
Notes

show interfaces ib internal notification

	show interfaces ib internal notification Displays information about internal links notification.
Syntax Description	N/A
Default	N/A
Configuration Mode	Any command mode
History	3.3.4318
History	3.4.3000	Updated example
Example	switch (config) # show interfaces ib internal notification ========================== Internal links information ========================== State change enabled : yes Speed mismatch enabled : yes Periodic notifications : 6 (hours)
Related Commands	interfaces ib internal notification
Notes

JSON API

json-gw enable

	json-gw enable no json-gw enable Enables the JSON API. The no form of the command disables the JSON API.
Syntax Description	N/A
Default	JSON API is enabled
Configuration Mode	config
History	3.6.3004
Example	switch (config) # json-gw enable
Related Commands	show json-gw
Notes

json-gw synchronous-request-timeout

	json-gw synchronous-request-timeout <timeout-value> no json-gw synchronous-request-timeout Defines a timeout value for synchronous JSON requests (in seconds). The no form of the command returns the timeout value to its default.
Syntax Description	timeout-value	Define a timeout value for synchronous JSON requests Range: 0-4294967295
Default	JSON API is enabled
Configuration Mode	config
History	3.6.3004
Example	switch (config) # json-gw synchronous-request-timeout 100
Related Commands	show json-gw
Notes

show json-gw

	show json-gw Displays the JSON API setting.
Syntax Description	N/A
Default	N/A
Configuration Mode	Any command mode
History	3.6.3004 3.6.4000: Updated example
Example	switch (config) # show json-gw JSON Gateway enabled: yes Synchronous request timeout: 30 JSON API version: 1.0
Related Commands	json-gw enable json-gw synchronous-request-timeout <time out value>
Notes

On This Page