Bug Fixes in this Firmware Version

Internal Ref.	Issue
2931516	Description: Added support for SPDM Get_measurements command. Note: Executing the command with a signature request without measurements, can cause an invalid L1 hash calculation.
	Keywords: SPDM
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3091233	Description: Added support for SPDM Challenge command.
	Keywords: SPDM
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
2907008	Description: Fixed PCIe link down failures during PCIe speed change tests.
	Keywords: PCIe, link down
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3134894	Description: Fixed an issue where `set_flow_table_entry` failed when `aso_flow_meter` action was used.
	Keywords: ASO Flow Meter, FW Steering
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.34.1002
3039007	Description: Enabled Multi-Host RX Rate-limiter configuration via the QEEC mlxreg and the max_shaper_rate field.
	Keywords: RX Rate-Limiter, Multi-host
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3059379	Description: Added "Command Unsupported" response code in cases when running the MCTP control command "Get Vendor Defined Messages Supported", and there were no supported VDMs.
	Keywords: MCTP control command
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3133476	Description: Added the following new checks to commands' interface: CREATE/MODIFY QP/DCT - blocking QP/DCT with adaptive routing (multi_path field) if gvmi has MKEY with Signature CREATE_MKEY- blocking the signature option if gvmi has open QPs/DCTs with the adaptive_routing feature enabled
	Keywords: Command checks
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3047521	Description: Implemented a firmware flow to power up/down the PLL from downstream links upon PERST assertion/de-assertion.
	Keywords: PLL, PERST
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3132594	Description: MAC allocation in adapter cards that support Port-Per-Host feature ("host isolation") is reordered to fit the required range. Note: After burning a new firmware, the user must power cycle the server, and run the DHCP flow to recover the MAC changes.
	Keywords: MAC allocation, PortPerHost
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3085879	Description: On rare occasions, when connecting a ConnectX-7 adapter card to an NVIDIA Spectrum-3 switch system using the optical cable OPN MFA1A00-C003, the link up time is ~7sec.
	Keywords: Optical cables, link up time
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
2994292	Description: Fixed a race condition occured between the duplicate read and QP commands (2RST, 2ERR and Destroy) in the signature that caused the command to hang.
	Keywords: Race condition
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.34.1002
3023847	Description: Enabled sending and receiving traffic with a different LID than the host LID in MetroX applications.
	Keywords: MetroX, LID based
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3023847	Description: Enabled sending and receiving traffic with a different LID than the host LID in MetroX applications.
	Keywords: MetroX, LID based
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
2920813	Description: The `an_disable` flow is not supported in ConnectX-7 adapter cards for 25GbE and 50G_2x link speeds when using one of the following cables: MT1841VS00827 (rev A4) MT1830VS00895 (rev A3) The flow is supported only when configuring FEC using the PPLM register.
	Keywords: AN, cables, 25GbE, FEC
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3039348	Description: Host Chaining is currently not supported in ConnectX-7 adapter cards.
	Keywords: Host Chaining
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3023751	Description: Link flapping may occur when using ConnectX-7 adapter cards with HDR optic cables.
	Keywords: Link flapping, HDR optic cables
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3046168	Description: Congestion Control is not enabled when one link type of different ports is different.
	Keywords: Congestion Control, Link Type, PCC
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3009525	Description: A Bit Error Rate (BER) of 1e-9 might occur when using optical cables.
	Keywords: BER
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3036791	Description: Configuring 400G_8x in force mode is currently not supported.
	Keywords: 400G_8x in force mode
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3004352	Description: LRO is currently not supported.
	Keywords: LRO
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002

Content

Space Tools

On This Page