Bug Fixes History

Internal Ref.	Issue
3227873	Description: Fixed an issue that caused RDE (Redfish) PATCH operation to `LLDPTransmit` properties `"ManagementAddressIPv4", "ManagementAddressIPv6"` and `"ManagementAddressMAC"` to be applied only in the first attempt but failed in the next.
	Keywords: RDE (Redfish) PATCH operation
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.35.1012
3172302	Description: Fixed an issue that caused the commands sent by the MLNX_OFED driver to the NIC to fail when loading the VirtIO driver.
	Keywords: vDPA, virtio-net full emulation
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.35.1012
3184625	Description: Fixed an issue that caused PLDM AEN event receiver media to be changed unexpectedly and destination BDF to be overridden with garbage when some PLDM packet were received from the SMBus layer.
	Keywords: PLDM AEN event receiver media
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.35.1012
3194359	Description: Fixed PCIe SKP OS generation interval for Gen1 and Gen2.
	Keywords: PCIe SKP
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.35.1012
2824427	Description: Running with a debug firmware reduces security as if token was applied.
	Keywords: Debug Firmware
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.35.1012
3110205	Description: Fixed inconsistent TCP performance when sending multiple streams.
	Keywords: Performance
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.35.1012

Internal Ref.	Issue
3110205	Description: Fixed inconsistent TCP performance when sending multiple streams.
	Keywords: Performance
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.34.4000
3138401	Description: Fixed an issue that caused host's PCI device to disappear after running 12V cycles in a loop while there was traffic between the hosts in a Multi-Host platform.
	Keywords: PCI device, Multi-Host platform, 12V cycles
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.34.4000
3148833	Description: Fixed an issue that resulted in lack of communication with the BMC from the host (IPv4/IPv6) when using BMC version v2022.22.1.
	Keywords: BMC
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.34.4000
3143956	Description: When connecting a ConnectX-7 adapter card to ConnectX-7 adapter card, once in few fwresets the link may raise in 1G speed instead of the highest speed enabled.
	Keywords: Speed rate
	Discovered in Version: 28.34.1002
	Fixed in Release: 28.34.4000

Internal Ref.	Issue
2931516	Description: Added support for SPDM Get_measurements command. Note: Executing the command with a signature request without measurements, can cause an invalid L1 hash calculation.
	Keywords: SPDM
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3091233	Description: Added support for SPDM Challenge command.
	Keywords: SPDM
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
2907008	Description: Fixed PCIe link down failures during PCIe speed change tests.
	Keywords: PCIe, link down
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3134894	Description: Fixed an issue where `set_flow_table_entry` failed when `aso_flow_meter` action was used.
	Keywords: ASO Flow Meter, FW Steering
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.34.1002
3039007	Description: Enabled Multi-Host RX Rate-limiter configuration via the QEEC mlxreg and the max_shaper_rate field.
	Keywords: RX Rate-Limiter, Multi-host
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3059379	Description: Added "Command Unsupported" response code in cases when running the MCTP control command "Get Vendor Defined Messages Supported", and there were no supported VDMs.
	Keywords: MCTP control command
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3133476	Description: Added the following new checks to commands' interface: CREATE/MODIFY QP/DCT - blocking QP/DCT with adaptive routing (multi_path field) if gvmi has MKEY with Signature CREATE_MKEY- blocking the signature option if gvmi has open QPs/DCTs with the adaptive_routing feature enabled
	Keywords: Command checks
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3047521	Description: Implemented a firmware flow to power up/down the PLL from downstream links upon PERST assertion/de-assertion.
	Keywords: PLL, PERST
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3132594	Description: MAC allocation in adapter cards that support Port-Per-Host feature ("host isolation") is reordered to fit the required range. Note: After burning a new firmware, the user must power cycle the server, and run the DHCP flow to recover the MAC changes.
	Keywords: MAC allocation, PortPerHost
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3085879	Description: On rare occasions, when connecting a ConnectX-7 adapter card to an NVIDIA Spectrum-3 switch system using the optical cable OPN MFA1A00-C003, the link up time is ~7sec.
	Keywords: Optical cables, link up time
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
2994292	Description: Fixed a race condition occured between the duplicate read and QP commands (2RST, 2ERR and Destroy) in the signature that caused the command to hang.
	Keywords: Race condition
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.34.1002
3023847	Description: Enabled sending and receiving traffic with a different LID than the host LID in MetroX applications.
	Keywords: MetroX, LID based
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3023847	Description: Enabled sending and receiving traffic with a different LID than the host LID in MetroX applications.
	Keywords: MetroX, LID based
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
2920813	Description: The `an_disable` flow is not supported in ConnectX-7 adapter cards for 25GbE and 50G_2x link speeds when using one of the following cables: MT1841VS00827 (rev A4) MT1830VS00895 (rev A3) The flow is supported only when configuring FEC using the PPLM register.
	Keywords: AN, cables, 25GbE, FEC
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3039348	Description: Host Chaining is currently not supported in ConnectX-7 adapter cards.
	Keywords: Host Chaining
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3023751	Description: Link flapping may occur when using ConnectX-7 adapter cards with HDR optic cables.
	Keywords: Link flapping, HDR optic cables
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3046168	Description: Congestion Control is not enabled when one link type of different ports is different.
	Keywords: Congestion Control, Link Type, PCC
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3009525	Description: A Bit Error Rate (BER) of 1e-9 might occur when using optical cables.
	Keywords: BER
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3036791	Description: Configuring 400G_8x in force mode is currently not supported.
	Keywords: 400G_8x in force mode
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002
3004352	Description: LRO is currently not supported.
	Keywords: LRO
	Discovered in Version: 28.33.4030
	Fixed in Release: 28.34.1002

Internal Ref.	Issue
2969829	Description: On rare occasions, the HDR speed link up time when using the optical module MFA7U10-H010 might take up to 70sec.
	Keywords: HDR, link up time, optical cable
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3024199	Description: When connecting a ConnectX-7 adapter card to an NVIDIA Quantum switch using the copper cable (MCP1600-E01AE30), the link is Down when in EDR speed.
	Keywords: EDR, copper cable, NVIDIA Quantum
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
2947588	Description: Trying to query/burn the firmware using the flint utility when the image is pending (after firmware burn and before firmware reset), results in the action's failure.
	Keywords: flint, query/burn firmware
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3047723	Description: When changing the protocols from ETH to IB on two ConnectX-7 adapter cards connected to each other, the ports on both sides must be toggled to get the link up.
	Keywords: Linkup, port toggling, protocol change
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030
3033874	Description: Connecting a ConnectX-7 adapter card to either a ConnectX-5 adapter card or to an NVIDIA Spectrum switch system is supported only when using a 100GbE optic cables and when configuring ConnectX-5 or the NVIDIA Spectrum switch system to Force Mode.
	Keywords: Linkup connectivity
	Discovered in Version: 28.33.2028
	Fixed in Release: 28.33.4030

Content

Space Tools

On This Page