Internal Ref. | Issue |
3272599 | Description: Removed the option to clear "Tx disable cap" for all non-baseT SFP modules. |
Keywords: Tx disable cap | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3339087 | Description: Added a split mask verification process to check whether or not a module is split in HCA. |
Keywords: Cables, split module | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3411270 | Description: Fixed an issue that resulted in firmware crash when setting large payload length values (more than ~1500) in NC-SI command's header. |
Keywords: NC-SI | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3405790 | Description: Fixed an issue that resulted in the interface type being shown as "unsupported" in CMIS modules. |
Keywords: CMIS | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3418889 | Description: Updated the NEGOTIATE_ALGORITHMS response according to the SPDM specification. |
Keywords: SPDM | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3409686 | Description: Added the option to clear the DPC registers after warm reboot. |
Keywords: DPC | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3411116 | Description: Fixed the configuration of the TS1s sent by the DownStream port (DSP) when moving to EQLZ.ph2. |
Keywords: DSP | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3138665 | Description: Changed the initial Tx preset configuration for the DownStream port (DSP). |
Keywords: Tx, DSP | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3138665 | Description: PLDM firmware update process fails in case 1304 bytes chunk size is chosen. |
Keywords: PLDM firmware update | |
Discovered in Version: 28.34.4000 | |
Fixed in Release: 28.37.1014 | |
3336619 | Description: Fixed an issues that occurred during secure firmware update when decrypting and authenticating each chunk of data using its authentication tag. The issue appeared when the main code chunk was split between the user chunks and any GCM operation (e.g., flash read with decryption). This GCM operation broke the GCM context for main chunk authentication and therefore failed. |
Keywords: Secure firmware update, GCM, code chunk | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3327847 | Description: CNP received, handled, and ignored counters in the hardware counters cannot work after moving to Programmable Congestion Control mode. |
Keywords: CNP, Programmable Congestion Control | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3336610 | Description: Fixed a rare issue that prevented the hardware from handling an error flow that occurred when accessing the DPA cluster L2 cache from the firmware processor. In this case the firmware processor hardware requested a VA=>PA translation from the internal mmio, and the address translation was broken by the mmio on the 4K page boundary. |
Keywords: Error handling, mmio, firmware processor | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 | |
3073517 | Description: When connecting a ConnectX-7 adapter card to a ConnectX-5 or an NVIDIA Spectrum switch and trying to raise 10G/40G over 100G optics cable is not supported. |
Keywords: Optical cables, ConnectX-5, NVIDIA Spectrum | |
Discovered in Version: 28.33.4030 | |
Fixed in Release: 28.37.1014 | |
3358994 | Description: Fixed an issue that prevented the hardware from consuming Port-VL and credits, which consequently blocked traffic from being transmitted due to a race condition between the firmware and the hardware when accessing the chip memory (CR space). |
Keywords: Firmware race, CR space, Port-VL | |
Discovered in Version: 28.36.1010 | |
Fixed in Release: 28.37.1014 |
Bug Fixes in this Firmware Version
NVIDIA ConnectX-5 Adapter Cards Firmware Release Notes v16.35.3502 LTS