Ethtool is a standard Linux utility for controlling network drivers and hardware, particularly for wired Ethernet devices. It can be used to:
- Get identification and diagnostic information
- Get extended device statistics
- Control speed, duplex, auto-negotiation and flow control for Ethernet devices
- Control checksum offload and other hardware offload features
- Control DMA ring sizes and interrupt moderation
- Flash device firmware using a .mfa2 image
Ethtool Supported Options
ethtool --set-priv-flags eth<x> <priv flag> <on/off>
Enables/disables driver feature matching the given private flag.
ethtool --show-priv-flags eth<x>
Shows driver private flags and their states (ON/OFF).
ethtool -a eth<x>
Queries the pause frame settings.
ethtool -A eth<x> [rx on|off] [tx on|off]
Sets the pause frame settings.
ethtool -c eth<x>
Queries interrupt coalescing settings.
ethtool -C eth<x> [pkt-rate-low N] [pkt-rate-high N] [rx-usecs-low N] [rx-usecs-high N]
Sets the values for packet rate limits and for moderation time high and low values.
ethtool -C eth<x> [rx-usecs N] [rx-frames N]
Sets the interrupt coalescing setting.
rx-frames will be enforced immediately, rx-usecs will be enforced only when adaptive moderation is disabled.
Note: usec settings correspond to the time to wait after the *last* packet is sent/received before triggering an interrupt.
ethtool -C eth<x> adaptive-rx on|off
Enables/disables adaptive interrupt moderation.
By default, the driver uses adaptive interrupt moderation for the receive path, which adjusts the moderation time to the traffic pattern.
ethtool -C eth<x> adaptive-tx on|off
Note: Supported by mlx5e for ConnectX-4 and above adapter cards.
Enables/disables adaptive interrupt moderation.
By default, the driver uses adaptive interrupt moderation for the transmit path, which adjusts the moderation parameters (time/frames) to the traffic pattern.
ethtool -g eth<x>
Queries the ring size values.
ethtool -G eth<x> [rx <N>] [tx <N>]
Modifies the ring size.
ethtool -i eth<x>
Checks driver and device information.
firmware-version: 4.6.4046 (MT_QEMU000000)
ethtool -k eth<x>
Queries the stateless offload status.
ethtool -K eth<x> [rx on|off] [tx on|off] [sg on|off] [tso on|off] [lro on|off] [gro on|off] [gso on|off] [rxvlan on|off] [txvlan on|off] [ntuple on/off] [rxhash on/off] [rx-all on/off] [rx-fcs on/off]
Sets the stateless offload status.
TCP Segmentation Offload (TSO), Generic Segmentation Offload (GSO): increase outbound throughput by reducing CPU overhead. It works by queuing up large buffers and letting the network interface card split them into separate packets.
Large Receive Offload (LRO): increases inbound throughput of high-bandwidth network connections by reducing CPU overhead. It works by aggregating multiple incoming packets from a single stream into a larger buffer before they are passed higher up the networking stack, thus reducing the number of packets that have to be processed. LRO is available in kernel versions < 3.1 for untagged traffic.
Hardware VLAN insertion Offload (txvlan): When enabled, the sent VLAN tag will be inserted into the packet by the hardware.
Note: LRO will be done whenever possible. Otherwise GRO will be done. Generic Receive Offload (GRO) is available throughout all kernels.
Hardware VLAN Striping Offload (rxvlan): When enabled received VLAN traffic will be stripped from the VLAN tag by the hardware.
RX FCS (rx-fcs): Keeps FCS field in the received packets.Sets the stateless offload status.
RX FCS validation (rx-all): Ignores FCS validation on the received packets.
ethtool -l eth<x>
Shows the number of channels.
ethtool -L eth<x> [rx <N>] [tx <N>]
Sets the number of channels.
ethtool -m|--dump-module-eeprom eth<x> [ raw on|off ] [ hex on|off ] [ offset N ] [ length N ]
Queries/decodes the cable module eeprom information.
ethtool -p|--identify DEVNAME
Enables visual identification of the port by LED blinking [TIME-IN-SECONDS].
ethtool -p|--identify eth<x> <LED duration>
Allows users to identify interface's physical port by turning the ports LED on for a number of seconds.
Note: The limit for the LED duration is 65535 seconds.
ethtool -S eth<x>
Obtains additional device statistics.
ethtool -s eth<x> advertise <N> autoneg on
Changes the advertised link modes to requested link modes <N>
To check the link modes’ hex values, run
For advertising new link modes, make sure to configure the entire bitmap as follows:
ethtool -s eth<x> msglvl [N]
Changes the current driver message level.
ethtool -s eth<x> speed <SPEED> autoneg off
Changes the link speed to requested <SPEED>. To check the supported speeds, run
Note: <autoneg off> does not set autoneg OFF, it only hints the driver to set a specific speed.
ethtool -t eth<x>
Performs a self-diagnostics test.
ethtool -T eth<x>
Shows time stamping capabilities
ethtool -x eth<x>
Retrieves the receive flow hash indirection table.
ethtool -X eth<x> equal a b c...
Sets the receive flow hash indirection table.
Note: The RSS table configuration is reset whenever the number of channels is modified (using ethtool -L command).
ethtool --show-fec eth<x>
Queries current Forward Error Correction (FEC) encoding in case FEC is supported.
Note: An output of "baser" implies Firecode encoding.
ethtool --set-fec eth<x> encoding auto|off|rs|baser
Configures Forward Error Correction (FEC).
Note: ‘baser’ encoding applies to the Firecode encoding, and ‘auto’ regards the HCA’s default.
ethtool -f|--flash <devname> FILE [N]
|Flash firmware image on the device using the specified .mfa2 file (FILE). By default, the command flashes all the regions on the device unless a region number (N) is specified.|