For bug fixes prior to version 24.33.1048, please refer to the NVIDIA BlueField-2 DPU documentation.
Internal Ref. | Issue |
3609404 | Description: Redirected multicast traffic to loopback only on MNG PF port using PT Tx loopback CAM HW mechanism. |
Keywords: Multicast traffic, loopback, MNG PF | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 | |
3629353 | Description: Fixed the cr_space in port configuration to prevent wrong timestamp of cqes. |
Keywords: Hardware timestamp | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 | |
3547022 | Description: Fixed an issue that resulted in reset failure when unloading network drivers on an external host and the sync1 reset is still reported as ‘supported’ although it is not. |
Keywords: sync1 reset | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 | |
3534774 | Description: Fixed an issue that prevented the Power Controller Control bit in the Slot Control register from returning to default when forcing the Unplug sequence. |
Keywords: Power Controller Control | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 | |
3602169 | Description: Added a locking mechanism to protect the firmware from a race condition between insertion and deletion of the same rule in parallel which occasionally resulted in firmware accessing a memory that has already been released, thus causing IOMMU / translation error. Note: This fix will not impact insertion rate for tables owned by SW steering. |
Keywords: Firmware steering | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 | |
3612682 | Description: Enabled live migration for virtio with mergeable buffer. |
Keywords: Virtio, Mergeable buffer, Live migration | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 | |
3571251 | Description: Fixed an issue that resulted in migration data corruption when running parallel save_vhca_state/load_vhca_state commands on the same PF. |
Keywords: VF live migration | |
Discovered in Version: 24.38.1002 | |
Fixed in Release: 24.39.2048 |
Internal Ref. | Issue |
3365411 | Description: Fixed a link failure that occurred due to a wrong ‘is_inphi_cable’ indication. |
Keywords: Link failure | |
Discovered in Version: 24.37.1300 | |
Fixed in Release: 24.38.1002 | |
3435583 | Description: Under certain configurations, during the loading of the PXE driver in Smart-NIC mode, the firmware attempts to lock the CMAS resources in ICMC sets that are full. This results in the failure of the locking and raises a health buffer indication. To prevent the above scenario, in this firmware version we improved the distribution of resource locking in ICMC. |
Keywords: ICMC locking | |
Discovered in Version: 24.37.1300 | |
Fixed in Release: 24.38.1002 | |
3331179 | Description: Improved token calculation. |
Keywords: Token calculation | |
Discovered in Version: 24.37.1300 | |
Fixed in Release: 24.38.1002 | |
3491841 | Description: Fixed a firmware assert that occurred when tried to verify if the module supported “swap”. |
Keywords: Firmware assert | |
Discovered in Version: 24.37.1300 | |
Fixed in Release: 24.38.1002 |
Internal Ref. | Issue |
3432548 | Description: Closed the attached QP doorbell to avoid any impact from the software side or the db_recovery mechanism |
Keywords: QP doorbell | |
Discovered in Version: 24.35.2000 | |
Fixed in Release: 24.37.1300 | |
3385129 | Description: Fixed an issue that resulted in high PTP offset by changing the RST value to 200, and adjusting the PTP Tx offset in PTP4L configuration. |
Keywords: PTP glitch, PTP constant offset | |
Discovered in Version: 24.35.2000 | |
Fixed in Release: 24.37.1300 | |
3233113 | Description: Disabled some HW optimization to prevent a HW race that caused an SQ to get stuck. |
Keywords: HW race, SQ | |
Discovered in Version: 24.33.1048 | |
Fixed in Release: 24.37.1300 | |
3306318 | Description: Fixed the issue that caused the virtio PXE boot to fail due to virtio BLK controller being stuck in continuous host warm reboot. |
Keywords: virtio full emulation, PXE boot, warm reboot | |
Discovered in Version: 24.35.2000 | |
Fixed in Release: 24.37.1300 | |
3327847 | Description: CNP received, handled, and ignored counters in the hardware counters cannot work after moving to Programmable Congestion Control mode. |
Keywords: CNP, Programmable Congestion Control | |
Discovered in Version: 24.35.2000 | |
Fixed in Release: 24.37.1300 |
Internal Ref. | Issue |
3217896 | Description: Fixed RDE PATCH operation status code reported in case the property is “read-only”. |
Keywords: RDE | |
Discovered in Version: 24.35.1012 | |
Fixed in Release: 24.35.2000 | |
3241357 | Description: Fixed an issue in MCTP-over-PCIe, where the VDM message with the type Route-to-Root Complex, the target ID was not set as 0x0. |
Keywords: MCTP-over-PCIe, VDM message | |
Discovered in Version: 24.35.1012 | |
Fixed in Release: 24.35.2000 | |
3250924 | Description: Fixed an issue that resulted in NVMe driver not loading on a hotplug-able device when VIRTIO_EMULATION_HOTPLUG_TRANS was enabled by mlxconfig. |
Keywords: VIRTIO_EMULATION_HOTPLUG_TRANS, NVMe | |
Discovered in Version: 24.35.1012 | |
Fixed in Release: 24.35.2000 | |
3215393 | Description: Fixed an issue that caused the virtual QoS mechanism to stop traffic from reaching the full line rate of 200GbE on each direction when LAG was enabled. |
Keywords: Virtual QoS mechanism, 200GbE, LAG | |
Discovered in Version: 24.35.1012 | |
Fixed in Release: 24.35.2000 |