Document Revision History
Added:
Section "RAS Logging"
Updated:
Section "Enabling Serial Redirect Mode to Run from Arm or BMC OS"
Section "Getting 3-port Switch Ports Mode"
Section "Configuring Router IPv6 Mode"
Section "Configuring IPv6 Static Router IP"
Section "Configuring IPv6 Static Router MAC"
Added:
Section "BIOS Debug Mode"
Sensor
ddr_temp
to section "Temperature Sensors"Sensor
ddr_temp
to section "SDR Sensor List"Informational note to page "BlueField Arm State"
Section "Data Port Module Events"
Section "Data Port Module Temperature Going High"
Section "Data Port Module Temperature Going Low"
Updated:
Section "Enabling/Disabling IPv6 DHCP"
Section "Serial Over LAN"
Section "Arm Frequency Change"
Section "BMC FRUs"
Notes about the size of a single BMC on "BMC and BlueField Logs"
Added:
Page "Guest Tunnel"
Page "Rsyslog"
Section "Retrieving Golden Image Version Information Using Redfish"
Updated:
Section "Redfish Management Interface"
Diagram on page "CEC and BMC Firmware Operations"
Multipart update with
MultipartHttpPushUri
command in section "Trigger Secure Firmware Update"Section "ForceUpdate"
Section "Updating BMC"
Section "Updating CEC"
Section "Installing BFB"
Section "Retrieve Information on Pending Settings"
Section "FRU Reading IPMI Commands"
Section "Hard Rebooting BlueField"
Section "Updating BMC"
Section "RAS Errors"
Section "System Commands"
Added:
Section "LLDP in Redfish"
Page "BlueField Arm State"
Section "Product Instance Identifier"
Section "CEC Activation and Reset" under "BMC and CEC Firmware Update"
Section "BMC DPU Information"
Updated:
Section "Installing BFB"
Section "FRU Reading IPMI Commands"
Added:
Section "Monitoring DPU OS Shutdown from BMC"
Section "Example for CSR Generation, Certificate Creation and Replacement"
Section "Redfish Event Log"
Cmds
0xa8 0x00
and0xa8 0x01
to "NVIDIA OEM Commands"
Updated:
Section "Changing Default Password"
Section "BIOS CA Certificates"
Section "System Commands"
Section "SEL Redfish Commands"
Section "Get Maximum Power Capacity"
Section "Get Dump Task State"
Section "BMC and CEC Firmware Update"
Added:
Section "Power Capping"
Section "DPU Chassis"
Section "BlueField Console Log"
Section "CA Certificates Collection Modification"
Section "Enable RShim on DPU BMC"
Section "Network Management Redfish Commands"
Section "CEC Update" under "BMC and CEC Firmware Update"
Section "OOB Network 3-Port Switch Control"
Appendix "Provisioning Software Upgrade Flow"
Updated:
Section "Boot Config Using Redfish"
Section "Installing BFB"
Section "Factory Reset BMC"
Section "Reset or Reboot BMC"
Section "BMC Sensor Data"
Section "Retrieving Data from BlueField Via IPMB"
Section "Serial Over LAN"
Section "BMC Dump Operations"
Added:
Section "System Inventory"
Section "DPU Chassis"
Section "NIC Subsystem Management"
Section "Table of Common Redfish Commands"
Updated:
Section "System FRU"
Section "System Logs"
Section "List of IPMI Supported FRUs"
Section "Boot Configuration"
Section "BIOS Secure Boot Configuration"
Section "BIOS Configuration"
Section "Reset Control"
Added:
Section "Changing Default Password"
Section "Account Service"
Section "Configuring BIOS Secure Boot"
Section "Configuring BIOS"
Section "Redfish Certificate Management"
The commands
0x32 0x97
and0x32 0x98
to "NVIDIA Custom Commands"
Updated:
Note in section "Network Protocol Support"
Section "Boot Configuration"
Section "Installing BFB"
Section "BMC and CEC Firmware Update" and its subsections
Added:
Figure "NVIDIA® BlueField®-3 BMC Connector" to section "BMC Console Interface"
Section "SEL Messages"
Section "Updating BMC and Glacier Firmware with Vendor Field Mode" which is relevant for NVIDIA® BlueField®-3 DPU only
Page "Serial Redirect Mode"
Section "BlueField BMC Redfish Triggers"
Command
0x32 0x92
and0x32 0x93
to "NVIDIA Custom Commands" table
Updated:
Section "BMC Management Interface" with new password requirements
Section "Sensor Data Record (SDR) Repository"
Link status codes to the p0_link and p1_link sensors in section "List of IPMI Supported Sensors"
Section "BMC and CEC Firmware Update"
Added:
Page "Vendor Field Mode"
Section "DPU Reset"
Updated:
Section "Boot Configuration" with note on DPU boot override setting
Updated:
NIC thermal sensors line in table under s ection "SDR Entry List"
Updated:
Page "NVIDIA OEM Commands"