Installation Troubleshooting and How-Tos
The following is a comprehensive list of the supported parameters to customize bf.cfg during BFB installation:
###############################################################################
# Configuration which can also be set in
# UEFI->Device Manager->System Configuration
###############################################################################
# Enable SMMU in ACPI.
#SYS_ENABLE_SMMU = TRUE
# Enable I2C0 in ACPI.
#SYS_ENABLE_I2C0 = FALSE
# Disable SPMI in ACPI.
#SYS_DISABLE_SPMI = FALSE
# Enable the second eMMC card which is only available on the BlueField Reference Platform.
#SYS_ENABLE_2ND_EMMC = FALSE
# Enable eMMC boot partition protection.
#SYS_BOOT_PROTECT = FALSE
# Enable SPCR table in ACPI.
#SYS_ENABLE_SPCR = FALSE
# Disable PCIe in ACPI.
#SYS_DISABLE_PCIE = FALSE
# Enable OP-TEE in ACPI.
#SYS_ENABLE_OPTEE = FALSE
###############################################################################
# Boot Order configuration
# Each entry BOOT<N> could have the following format:
# PXE:
# BOOT<N> = NET-<NIC_P0 | NIC_P1 | OOB | RSHIM>-<IPV4 | IPV6>
# PXE over VLAN (vlan-id in decimal):
# BOOT<N> = NET-<NIC_P0 | NIC_P1 | OOB | RSHIM>[.<vlan-id>]-<IPV4 | IPV6>
# UEFI Shell:
# BOOT<N> = UEFI_SHELL
# DISK: boot entries created during OS installation.
# BOOT<N> = DISK
###############################################################################
# This example configures PXE boot over the 2nd ConnectX port.
# If fails, it continues to boot from disk with boot entries created during OS
# installation.
#BOOT0 = NET-NIC_P1-IPV4
#BOOT1 = DISK
###############################################################################
# Other misc configuration
###############################################################################
# MAC address of the rshim network interface (tmfifo_net0).
#NET_RSHIM_MAC = 00:1a:ca:ff:ff:01
# DHCP class identifier for PXE (arbitrary string up to 32 characters)
#PXE_DHCP_CLASS_ID = NVIDIA/BF/PXE
# Create dual boot partition scheme (Ubuntu only)
# DUAL_BOOT=yes
# Upgrade NIC firmware
# WITH_NIC_FW_UPDATE=yes
# Target storage device for the DPU OS (Default SSD: /dev/nvme0n1)
device=/dev/nvme0n1
# bfb_modify_os – SHELL function called after file the system is extracted on the target partitions.
# It can be used to modify files or create new files on the target file system mounted under
# /mnt. So the file path should look as follows: /mnt/<expected_path_on_target_OS>. This
# can be used to run a specific tool from the target OS (remember to add /mnt to the path for
# the tool).
# bfb_pre_install – SHELL function called before EMMC partitions format
# and OS filesystem is extracted
# bfb_post_install – SHELL function called as a last step before reboot.
# All EMMC partitions are unmounted at this stage.
Upgrade to the latest stable boot partition images, see "How to upgrade the boot partition (ATF & UEFI) without re-installation".
If the .bfb file cannot recognize the BlueField board type, it reverts to low core operation. The following message will be printed on your screen:
***System type can't be determined***
***Booting as a minimal system***
Please contact NVIDIA Support if this occurs.
The following errors appear in console if images are corrupted or not signed properly:
Device |
Error |
BlueField |
ERROR: Failed to load BL2 firmware |
BlueField-2 |
ERROR: Failed to load BL2R firmware |
BlueField-3 |
Failed to load PSC-BL1 or PSC VERIFY_BCT timeout |
This is most likely configuration related.
If installing through the RShim interface, check whether /var/pxe/centos7 is mounted or not. If not, either manually mount it or re-run the setup.sh script.
Check the Linux boot message to see whether eMMC is found or not. If not, the BlueField driver patch is missing. For local installation via RShim, run the setup.sh script with the absolute path and check if there are any errors. For a corporate PXE server, make sure the BlueField and ConnectX driver disk are patched into the initrd image.
Run the following:
/opt/mellanox/scripts/bfvcheck:
root@bluefield:/usr/bin/bfvcheck# ./bfvcheck
Beginning version check...
-RECOMMENDED VERSIONS-
ATF: v1.5(release):BL2.0-1-gf9f7cdd
UEFI: 2.0-6004a6b
FW: 18.25.1010
-INSTALLED VERSIONS-
ATF: v1.5(release):BL2.0-1-gf9f7cdd
UEFI: 2.0-6004a6b
FW: 18.25.1010
Version checked
Also, the version information is printed to the console.
For ATF, a version string is printed as the system boots.
"NOTICE: BL2: v1.3(release):v1.3-554-ga622cde"
For UEFI, a version string is printed as the system boots.
"UEFI firmware (version 0.99-18d57e3 built at 00:55:30 on Apr 13 2018)"
For Yocto, run:
$ cat /etc/bluefield_version
2.0.0.10817
See the readme at <BF_INST_DIR>/src/drivers/rshim/README.
Boot the target through the RShim interface from a host machine:
$ cat <BF_INST_DIR>/sample/install.bfb > /dev/rshim<N>/boot
Log into the BlueField target:
$ /opt/mlnx/scripts/bfrec
The mst, mlxburn, and flint tools can be used to update firmware.
For Ubuntu, CentOS and Debian, run the following command from the Arm side:
sudo /opt/mellanox/mlnx-fw-updater/mlnx_fw_updater.pl
Configuring ConnectX firmware can be done using the mlxconfig tool.
It is possible to configure privileges of both the internal (Arm) and the external host (for DPUs) from a privileged host. According to the configured privilege, a host may or may not perform certain operations related to the NIC (e.g. determine if a certain host is allowed to read port counters).
For more information and examples please refer to the MFT User Manual which can be found at the following link.
Press the "Esc" key when prompted after booting (before the countdown timer runs out) to enter the UEFI boot menu and use the arrows to select the menu option.
It could take 1-2 minutes to enter the Boot Manager depending on how many devices are installed or whether the EXPROM is programmed or not.
Once in the boot manager:
"EFI Network xxx" entries with device path "PciRoot..." are ConnectX interface
"EFI Network xxx" entries with device path "MAC(..." are for the RShim interface and the BlueField OOB Ethernet interface
Select the interface and press ENTER will start PXE boot.
The following are several useful commands under UEFI shell:
Shell> ls FS0: # display file
Shell> ls FS0:\EFI # display file
Shell> cls # clear screen
Shell> ifconfig -l # show interfaces
Shell> ifconfig -s eth0 dhcp # request DHCP
Shell> ifconfig -l eth0 # show one interface
Shell> tftp 192.168.100.1 grub.cfg FS0:\grub.cfg # tftp download a file
Shell> bcfg boot dump # dump boot variables
Shell> bcfg boot add 0 FS0:\EFI\centos\shim.efi "CentOS" # create an entry
The default Yocto kernel has CONFIG_KGDB and CONFIG_KGDB_SERIAL_CONSOLE enabled. This allows the Linux kernel on BlueField to be debugged over the serial port. A single serial port cannot be used both as a console and by KGDB at the same time. It is recommended to use the RShim for console access (/dev/rshim0/console) and the UART port (/dev/ttyAMA0 or /dev/ttyAMA1) for KGDB. Kernel GDB over console (KGDBOC) does not work over the RShim console. If the RShim console is not available, there are open-source packages such as KGDB demux and agent-proxy which allow a single serial port to be shared.
There are two ways to configure KGDBOC. If the OS is already booted, then write the name of the serial device to the KGDBOC module parameter. For example:
$ echo ttyAMA1 > /sys/module/kgdboc/parameters/kgdboc
To attach GDB to the kernel, it must be stopped first. One way to do that is to send a "g" to /proc/sysrq-trigger.
$ echo g > /proc/sysrq-trigger
To debug incidents that occur at boot time, kernel boot parameters must be configured. Add "kgdboc=ttyAMA1,115200 kgdwait" to the boot arguments to use UART1 for debugging and force it to wait for GDB to attach before booting.
Once the KGDBOC module is configured and the kernel stopped, run the Arm64 GDB on the host machine connected to the serial port, then set the remote target to the serial device on the host side.
<BF_INST_DIR>/sdk/sysroots/x86_64-pokysdk-linux/usr/bin/aarch64-poky-linux/aarch64-poky-linux-gdb <BF_INST_DIR>/sample/vmlinux
(gdb) target remote /dev/ttyUSB3
Remote debugging using /dev/ttyUSB3
arch_kgdb_breakpoint () at /labhome/dwoods/src/bf/linux/arch/arm64/include/asm/kgdb.h:32
32 asm ("brk %0" : : "I" (KGDB_COMPILED_DBG_BRK_IMM));
(gdb)
<BF_INST_DIR> is the directory where the BlueField software is installed. It is assumed that the SDK has been unpacked in the same directory.
SMMU could affect performance for certain applications. It is disabled by default and can be modified in different ways.
Enable/disable SMMU in the UEFI System Configuration
Set it in bf.cfg and push it together with the install.bfb (see section "Installing Popular Linux Distributions on BlueField")
In BlueField Linux, create a file with one line with SYS_ENABLE_SMMU=TRUE, then run bfcfg.
The configuration change will take effect after reboot. The configuration value is stored in a persistent UEFI variable. It is not modified by OS installation.
See section "UEFI System Configuration" for information on how to access the UEFI System Configuration menu.
On UART0:
$ echo "console=ttyAMA0 earlycon=pl011,0x01000000 initrd=initramfs" > bootarg
$ <BF_INST_DIR>/bin/mlx-mkbfb --boot-args bootarg \
<BF_INST_DIR>/sample/ install.bfb
On UART1:
$ echo "console=ttyAMA1 earlycon=pl011,0x01000000 initrd=initramfs" > bootarg
$ <BF_INST_DIR>/bin/mlx-mkbfb --boot-args bootarg \
<BF_INST_DIR>/sample/install.bfb
On RShim:
$ echo "console=hvc0 initrd=initramfs" > bootarg
$ <BF_INST_DIR>/bin/mlx-mkbfb --boot-args bootarg \
<BF_INST_DIR>/sample/install.bfb
On Ubuntu OS, the default network configuration for tmfifo_net0 and oob_net0 interfaces is set by the cloud-init service upon first boot after BFB installation.
The default content of /var/lib/cloud/seed/nocloud-net/network-config as follows:
# cat /var/lib/cloud/seed/nocloud-net/network-config
version: 2
renderer: NetworkManager
ethernets:
tmfifo_net0:
dhcp4: false
addresses:
- 192.168.100.2/30
nameservers:
addresses: [ 192.168.100.1 ]
routes:
- to: 0.0.0.0/0
via: 192.168.100.1
metric: 1025
oob_net0:
dhcp4: true
This content can be modified during BFB installation using bf.cfg. For example:
# cat bf.cfg
bfb_modify_os()
{
sed -i -e '/oob_net0/,+1d' /mnt/var/lib/cloud/seed/nocloud-net/network-config
cat >> /mnt/var/lib/cloud/seed/nocloud-net/network-config << EOF
oob_net0:
dhcp4: false
addresses:
- 10.0.0.1/24
EOF
}
# bfb-install -c bf.cfg -r rshim0 -b <BFB>
Using the same technique, any configuration file on the BlueField DPU side can be updated during the BFB installation process.