NVIDIA BlueField DPU BSP v4.5.0

Deploying BlueField Software Using BFB from Host

Note

It is recommended to upgrade your BlueField product to the latest software and firmware versions available to benefit from new features and latest bug fixes.

Warning

This procedure assumes that a BlueField DPU has already been installed in a server according to the instructions detailed in the DPU's hardware user guide.

The following table lists an overview of the steps required to install Ubuntu BFB on your DPU:

Step

Procedure

Link to Section

1

Uninstall previous DOCA on host (if exists)

Uninstall Previous Software from Host

2

Install RShim on the host

Install RShim on Host

3

Verify that RShim is running on the host

Ensure RShim Running on Host

4

Change the default credentials using bf.cfg file (optional)

Changing Default Credentials Using bf.cfg

5

Install the Ubuntu BFB image

BFB Installation

6

Verify installation completed successfully

Verify BFB is Installed

7

Upgrade the firmware on your DPU

Firmware Upgrade

If an older DOCA software version is installed on your host, make sure to uninstall it before proceeding with the installation of the new version:

Ubuntu

Copy
Copied!
            

host# for f in $( dpkg --list | grep doca | awk '{print $2}' ); do echo $f ; apt remove --purge $f -y ; done host# sudo apt-get autoremove

CentOS/RHEL

Copy
Copied!
            

host# for f in $(rpm -qa |grep -i doca ) ; do yum -y remove $f; done host# yum autoremove host# yum makecache

Before installing the RShim driver, verify that the RShim devices, which will be probed by the driver, are listed under lsusb or lspci.

Copy
Copied!
            

lspci | grep -i nox

Output example:

Copy
Copied!
            

27:00.0 Ethernet controller: Mellanox Technologies MT42822 BlueField-2 integrated ConnectX-6 Dx network controller 27:00.1 Ethernet controller: Mellanox Technologies MT42822 BlueField-2 integrated ConnectX-6 Dx network controller 27:00.2 Non-Volatile memory controller: Mellanox Technologies NVMe SNAP Controller 27:00.3 DMA controller: Mellanox Technologies MT42822 BlueField-2 SoC Management Interface // This is the RShim PF

RShim is compiled as part of the doca-tools package in the doca-host-repo-ubuntu<version>_amd64 file (.deb or .rpm).

To install doca-tools:

OS

Procedure

Ubuntu/Debian

  1. Download the DOCA Tools host package from the "Installation Files" section in the NVIDIA DOCA Installation Guide for Linux.

  2. Unpack the deb repo. Run:

    Copy
    Copied!
                

    host# sudo dpkg -i doca-host-repo-ubuntu<version>_amd64.deb

  3. Perform apt update. Run:

    Copy
    Copied!
                

    host# sudo apt-get update

  4. Run apt install for DOCA Tools.

    Copy
    Copied!
                

    host# sudo apt install doca-tools

CentOS/RHEL 7.x

  1. Download the DOCA Tools host package from the "Installation Files" section in the NVIDIA DOCA Installation Guide for Linux.

  2. Unpack the RPM repo. Run:

    Copy
    Copied!
                

    host# sudo rpm -Uvh doca-host-repo-rhel<version>.x86_64.rpm

  3. Enable new yum repos. Run:

    Copy
    Copied!
                

    host# sudo yum makecache

  4. Run yum install to install DOCA Tools.

    Copy
    Copied!
                

    host# sudo yum install doca-tools

CentOS/RHEL 8.x or Rocky 8.6

  1. Download the DOCA Tools host package from the "Installation Files" section in the NVIDIA DOCA Installation Guide for Linux.

  2. Unpack the RPM repo. Run:

    Copy
    Copied!
                

    host# sudo rpm -Uvh doca-host-repo-rhel<version>.x86_64.rpm

  3. Enable new dnf repos. Run:

    Copy
    Copied!
                

    host# sudo dnf makecache

  4. Run dnf install to install DOCA Tools.

    Copy
    Copied!
                

    host# sudo dnf install doca-tools

  1. Verify RShim status. Run:

    Copy
    Copied!
                

    sudo systemctl status rshim

    Expected output:

    Copy
    Copied!
                

    active (running) ... Probing pcie-0000:<DPU’s PCIe Bus address on host> create rshim pcie-0000:<DPU’s PCIe Bus address on host> rshim<N> attached

    Where <N> denotes RShim enumeration starting with 0 (then 1, 2, etc.) for every additional DPU installed on the server.

    If the text "another backend already attached" is displayed, users will not be able to use RShim on the host. Please refer to "RShim Troubleshooting and How-Tos" to troubleshoot RShim issues.

    1. If the previous command displays inactive or another error, restart RShim service. Run:

      Copy
      Copied!
                  

      sudo systemctl restart rshim

    2. Verify RShim status again. Run:

      Copy
      Copied!
                  

      sudo systemctl status rshim

      If this command does not display "active (running)", then refer to "RShim Troubleshooting and How-Tos".

  2. Display the current setting. Run:

    Copy
    Copied!
                

    # cat /dev/rshim<N>/misc | grep DEV_NAME DEV_NAME pcie-0000:04:00.2

    This output indicates that the RShim service is ready to use.

Warning

It is is important to learn your DPU's device-id for performing some of the software installations or upgrades in this guide.

To determine the device ID of the DPUs on your setup, run:

Copy
Copied!
            

mst start mst status -v

Example output:

Copy
Copied!
            

MST modules: ------------ MST PCI module is not loaded MST PCI configuration module loaded PCI devices: ------------ DEVICE_TYPE MST PCI RDMA NET NUMA BlueField2(rev:1) /dev/mst/mt41686_pciconf0.1 3b:00.1 mlx5_1 net-ens1f1 0   BlueField2(rev:1) /dev/mst/mt41686_pciconf0 3b:00.0 mlx5_0 net-ens1f0 0   BlueField3(rev:1)       /dev/mst/mt41692_pciconf0.1   e2:00.1   mlx5_1          net-ens7f1np1             4   BlueField3(rev:1)       /dev/mst/mt41692_pciconf0     e2:00.0   mlx5_0          net-ens7f0np0             4

The device IDs for the BlueField-2 and BlueField-3 DPUs in this example are /dev/mst/mt41686_pciconf0 and /dev/mst/mt41692_pciconf0 respectively.

Changing Default Credentials Using bf.cfg

Ubuntu users are prompted to change the default password (ubuntu) for the default user (ubuntu) upon first login. Logging in will not be possible even if the login prompt appears until all services are up ("DPU is ready" message appears in /dev/rshim0/misc).

Warning

Attempting to log in before all services are up prints the following message: "Permission denied, please try again."

Alternatively, Ubuntu users can provide a unique password that will be applied at the end of the BFB installation. This password would need to be defined in a bf.cfg configuration file. To set the password for the ubuntu user:

  1. Create password hash. Run:

    Copy
    Copied!
                

    # openssl passwd -1 Password: Verifying - Password: $1$3B0RIrfX$TlHry93NFUJzg3Nya00rE1

  2. Add the password hash in quotes to the bf.cfg file:

    Copy
    Copied!
                

    # vim bf.cfg ubuntu_PASSWORD='$1$3B0RIrfX$TlHry93NFUJzg3Nya00rE1'

    The bf.cfg file is used with the bfb-install script in the steps that follow.

    Warning

    Password policy:

    • Minimum password length – 8

    • At least one upper-case letter

    • At least one lower-case letter

    • At least one numerical character

Warning

For a comprehensive list of the supported parameters to customize bf.cfg during BFB installation, refer to section "bf.cfg Parameters".


GRUB Password Protection

GRUB menu entries are protected by a username and password to prevent unwanted changes to the default boot options or parameters.

The default credentials are as follows:

Username

admin

Password

BlueField

The password can be changed during BFB installation by providing a new grub_admin_PASSWORD parameter in bf.cfg:

Copy
Copied!
            

# vim bf.cfg grub_admin_PASSWORD=’ grub.pbkdf2.sha512.10000.5EB1FF92FDD89BDAF3395174282C77430656A6DBEC1F9289D5F5DAD17811AD0E2196D0E49B49EF31C21972669D180713E265BB2D1D4452B2EA9C7413C3471C53.F533423479EE7465785CC2C79B637BDF77004B5CC16C1DDE806BCEA50BF411DE04DFCCE42279E2E1F605459F1ABA3A0928CE9271F2C84E7FE7BF575DC22935B1’

To get a new encrypted password value use the command grub-mkpasswd-pbkdf2.

After the installation, the password can be updated by editing the file /etc/grub.d/40_custom and then running the command update-grub which updates the file /boot/grub/grub.cfg.

BFB Installation

Note

Check the BFB version installed on your BlueField-2 DPU. If the version is 1.5.0 or lower, please see Known Issue Reference #3600716 under Known Issues section.

Warning

Installing the BFB does not update the firmware by default. To install the NIC firmware during BFB upgrade, perform the following offline before sending the BFB file:

  1. Generate the bf.cfg file and combine it with the BFB file:

    Copy
    Copied!
                

    # echo WITH_NIC_FW_UPDATE=yes > bf.cfg # cat <path_to_bfb> bf.cfg > new.bfb

  2. Utilize the newly created BFB file, new.bfb, while following the instructions below.

A pre-built BFB of Ubuntu 20.04 with DOCA Runtime and DOCA packages installed is available on the NVIDIA DOCA SDK developer zone page.

Warning

All new BlueField-2 devices are secure boot enabled, hence all SW images must be signed by NVIDIA in order to boot. All formally published SW images are signed.

To install Ubuntu BFB, run on the host side:

Copy
Copied!
            

# bfb-install -h syntax: bfb-install --bfb|-b <BFBFILE> [--config|-c <bf.cfg>] \ [--rootfs|-f <rootfs.tar.xz>] --rshim|-r <rshimN> [--help|-h]

The bfb-install utility is installed by the RShim package.

This utility script pushes the BFB image and optional configuration (bf.cfg file) to the BlueField side and checks and prints the BFB installation progress. To see the BFB installation progress, please install the pv Linux tool.

Important

BFB image installation must complete before restarting the system/BlueField. Doing so may result in the BlueField DPU not operating as expected (e.g., it may not be accessible using SSH). If this happens, re-initiate the update process with bfb-install t o recover the DPU.

The following is an output example of Ubuntu 20.04 installation with the bfb-install script assuming pv has been installed.

Copy
Copied!
            

# bfb-install --bfb <BlueField-BSP>.bfb --config bf.cfg --rshim rshim0 Pushing bfb + cfg 1.21GiB 0:01:14 [16.5MiB/s] [ <=> ] Collecting BlueField booting status. Press Ctrl+C to stop… INFO[PSC]: PSC BL1 START INFO[BL2]: start INFO[BL2]: DDR POST passed INFO[BL2]: UEFI loaded INFO[BL31]: start INFO[BL31]: lifecycle Production INFO[BL31]: VDD adjustment complete INFO[BL31]: VDD adjustment complete INFO[BL31]: power capping disabled INFO[BL31]: runtime INFO[UEFI]: eMMC init INFO[UEFI]: eMMC probed INFO[UEFI]: UPVS valid INFO[UEFI]: PMI: updates started INFO[UEFI]: PMI: boot image update INFO[UEFI]: PMI: updates completed, status 0 INFO[UEFI]: PCIe enum start INFO[UEFI]: PCIe enum end INFO[UEFI]: exit Boot Service INFO[MISC]: Found bf.cfg INFO[MISC]: Ubuntu installation started INFO[MISC]: Installing OS image INFO[MISC]: Changing the default password for user ubuntu INFO[MISC]: Running bfb_modify_os from bf.cfg INFO[MISC]: ===================== bfb_modify_os ===================== INFO[MISC]: Installation finished INFO[MISC]: Rebooting...


Verify BFB is Installed

After installation of the Ubuntu OS is complete, the following note appears in /dev/rshim0/misc on first boot:

Copy
Copied!
            

... INFO[MISC]: Linux up INFO[MISC]: DPU is ready

"DPU is ready" indicates that all the relevant services are up and users can login the system.

After the installation of the Ubuntu 20.04 BFB, the configuration detailed in the following sections is generated.

Warning

Make sure all the services (including cloud-init) are started on BlueField and to perform a graceful shutdown before power cycling the host server.

BlueField OS image version is stored under /etc/mlnx-release in the DPU.

Copy
Copied!
            

# cat /etc/mlnx-release DOCA_2.6.0_BSP_4.6.0_Ubuntu_22.04-<version>

Firmware Upgrade

Warning

mlxfwreset is not supported in this release. Please perform a graceful shutdown, and power cycle the host where mlxfwreset is requested.

To upgrade firmware:

  1. Set a temporary static IP on the host. Run:

    Copy
    Copied!
                

    sudo ip addr add 192.168.100.1/24 dev tmfifo_net0

  2. SSH to your DPU via 192.168.100.2 (preconfigured). The default credentials for Ubuntu are as follows.

    Username

    Password

    ubuntu

    Set during installation

    For example:

    Copy
    Copied!
                

    ssh ubuntu@192.168.100.2 Password: <unique-password>

  3. Upgrade the firmware on the DPU. Run:

    Copy
    Copied!
                

    sudo /opt/mellanox/mlnx-fw-updater/mlnx_fw_updater.pl --force-fw-update

    Example output:

    Copy
    Copied!
                

    Device #1: ----------   Device Type: BlueField-2 [...] Versions: Current Available FW <Old_FW> <New_FW>

    Warning

    Important! To apply NVConfig changes, stop here and follow the steps in section "Updating NVConfig Params".

  4. Perform a graceful shutdown and p ower cycle the host for the changes to take effect.

Updating NVConfig Params

  1. Reset the nvconfig params to their default values:

    Copy
    Copied!
                

    # sudo mlxconfig -d /dev/mst/<device-id> -y reset   Reset configuration for device /dev/mst/<device-name>? (y/n) [n] : y Applying... Done! -I- Please reboot machine to load new configurations.

    Warning

    To learn the device ID of the DPUs on your setup, run:

    Copy
    Copied!
                

    mst start mst status -v

    Example output:

    Copy
    Copied!
                

    MST modules: ------------ MST PCI module is not loaded MST PCI configuration module loaded PCI devices: ------------ DEVICE_TYPE MST PCI RDMA NET NUMA BlueField2(rev:1) /dev/mst/mt41686_pciconf0.1 3b:00.1 mlx5_1 net-ens1f1 0   BlueField2(rev:1) /dev/mst/mt41686_pciconf0 3b:00.0 mlx5_0 net-ens1f0 0   BlueField3(rev:1)       /dev/mst/mt41692_pciconf0.1   e2:00.1   mlx5_1          net-ens7f1np1             4   BlueField3(rev:1)       /dev/mst/mt41692_pciconf0     e2:00.0   mlx5_0          net-ens7f0np0             4

    The device IDs for the BlueField-2 and BlueField-3 DPUs in this example are /dev/mst/mt41686_pciconf0 and /dev/mst/mt41692_pciconf0 respectively.

  2. (Optional) Enable NVMe emulation. Run:

    Copy
    Copied!
                

    sudo mlxconfig -d <device-id> s NVME_EMULATION_ENABLE=1

  3. Skip this step if your BlueField DPU is Ethernet only. Please refer to section "Supported Platforms and Interoperability" under the Release Notes to learn your DPU type.

    If you have a VPI DPU, the default link type of the ports will be configured to IB. If you want to change the link type to Ethernet, please run the following configuration:

    Copy
    Copied!
                

    sudo mlxconfig -d <device-id> s LINK_TYPE_P1=2 LINK_TYPE_P2=2

  4. Perform a graceful shutdown and power cycle the host for the mlxconfig settings to take effect.

Customizations During BFB Installation

Using configuration parameters in the bf.cfg file, the BlueField's boot options and OS can be further customized. For a full list of the supported parameters to customize your DPU system during BFB installation, refer to section "bf.cfg Parameters". In addition to parameters, the bf.cfg file offers control over customization of the BlueField firmware and OS through scripting.

Add any of the following functions to the bf.cfg file for them to be called by the install.sh script embedded in the BFB:

  • bfb_modify_os – called after file the system is extracted on the target partitions. It can be used to modify files or create new files on the target file system mounted under /mnt. So the file path should look as follows: /mnt/<expected_path_on_target_OS>. This can be used to run a specific tool from the target OS (remember to add /mnt to the path for the tool).

  • bfb_pre_install – called before eMMC/SSD partitions format and OS filesystem is extracted

  • bfb_post_install – called as a last step before reboot. All eMMC/SSD partitions are unmounted at this stage.

For example, the bf.cfg script below disables OVS bridge creation upon boot:

Copy
Copied!
            

# cat /root/bf.cfg   bfb_modify_os() { log ===================== bfb_modify_os ===================== log "Disable OVS bridges creation upon boot" sed -i -r -e 's/(CREATE_OVS_BRIDGES=).*/\1"no"/' /mnt/etc/mellanox/mlnx-ovs.conf }   bfb_pre_install() { log ===================== bfb_pre_install ===================== }   bfb_post_install() { log ===================== bfb_post_install ===================== }

Warning

After modifying files on the BlueField DPU, run the command sync to flush file system buffers to eMMC/SSD flash memory to avoid data loss during reboot or power cycle.


Default Ports and OVS Configuration

The /sbin/mlnx_bf_configure script runs automatically with ib_umad kernel module loaded (see /etc/modprobe.d/mlnx-bf.conf) and performs the following configurations:

  1. Ports are configured with switchdev mode and software steering.

  2. RDMA device isolation in network namespace is enabled.

  3. Two scalable function (SF) interfaces are created (one per port) if BlueField is configured with Embedded CPU mode (default):

    Copy
    Copied!
                

    # mlnx-sf -a show   SF Index: pci/0000:03:00.0/229408 Parent PCI dev: 0000:03:00.0 Representor netdev: en3f0pf0sf0 Function HWADDR: 02:61:f6:21:32:8c Auxiliary device: mlx5_core.sf.2 netdev: enp3s0f0s0 RDMA dev: mlx5_2   SF Index: pci/0000:03:00.1/294944 Parent PCI dev: 0000:03:00.1 Representor netdev: en3f1pf1sf0 Function HWADDR: 02:30:13:6a:2d:2c Auxiliary device: mlx5_core.sf.3 netdev: enp3s0f1s0 RDMA dev: mlx5_3

    The parameters for these SFs are defined in configuration file /etc/mellanox/mlnx-sf.conf.

    Copy
    Copied!
                

    /sbin/mlnx-sf --action create --device 0000:03:00.0 --sfnum 0 --hwaddr 02:61:f6:21:32:8c /sbin/mlnx-sf --action create --device 0000:03:00.1 --sfnum 0 --hwaddr 02:30:13:6a:2d:2c

    Warning

    To avoid repeating a MAC address in the your network, the SF MAC address is set randomly upon BFB installation. You may choose to configure a different MAC address that better suit your network needs.

  4. Two OVS bridges are created:

    Copy
    Copied!
                

    # ovs-vsctl show f08652a8-92bf-4000-ba0b-7996c772aff6 Bridge ovsbr2 Port ovsbr2 Interface ovsbr2 type: internal Port p1 Interface p1 Port en3f1pf1sf0 Interface en3f1pf1sf0 Port pf1hpf Interface pf1hpf Bridge ovsbr1 Port p0 Interface p0 Port pf0hpf Interface pf0hpf Port ovsbr1 Interface ovsbr1 type: internal Port en3f0pf0sf0 Interface en3f0pf0sf0 ovs_version: "2.14.1"

    The parameters for these bridges are defined in configuration file /etc/mellanox/mlnx-ovs.conf:

    Copy
    Copied!
                

    CREATE_OVS_BRIDGES="yes" OVS_BRIDGE1="ovsbr1" OVS_BRIDGE1_PORTS="p0 pf0hpf en3f0pf0sf0" OVS_BRIDGE2="ovsbr2" OVS_BRIDGE2_PORTS="p1 pf1hpf en3f1pf1sf0" OVS_HW_OFFLOAD="yes" OVS_START_TIMEOUT=30

    Warning

    If failures occur in /sbin/mlnx_bf_configure or configuration changes happen (e.g. switching to separated host mode) OVS bridges are not created even if CREATE_OVS_BRIDGES="yes".

  5. OVS HW offload is configured.

Default Network Interface Configuration

Network interfaces are configured using the netplan utility:

Copy
Copied!
            

# cat /etc/netplan/50-cloud-init.yaml # This file is generated from information provided by the datasource. Changes # to it will not persist across an instance reboot. To disable cloud-init's # network configuration capabilities, write a file # /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following: # network: {config: disabled} network: ethernets: tmfifo_net0: addresses: - 192.168.100.2/30 dhcp4: false nameservers: addresses: - 192.168.100.1 routes: - metric: 1025 to: 0.0.0.0/0 via: 192.168.100.1 oob_net0: dhcp4: true renderer: NetworkManager version: 2   # cat /etc/netplan/60-mlnx.yaml network: ethernets: enp3s0f0s0: dhcp4: 'true' enp3s0f1s0: dhcp4: 'true' renderer: networkd version: 2

BlueField DPUs also have a local IPv6 (LLv6) derived from the MAC address via the STD stack mechanism. For a default MAC, 00:1A:CA:FF:FF:01, the LLv6 address would be fe80::21a:caff:feff:ff01.

For multi-device support, the LLv6 address works with SSH for any number of DPUs in the same host by including the interface name in the SSH command:

Copy
Copied!
            

ssh -6 ubuntu@fe80::21a:caff:feff:ff01%tmfifo_net<n>

Warning

If tmfifo_net<n> on the host does not have an LLv6 address, restart the RShim driver:

Copy
Copied!
            

systemctl restart rshim


To improve the boot time, the following optimizations were made to Ubuntu OS image:

Copy
Copied!
            

# cat /etc/systemd/system/systemd-networkd-wait-online.service.d/override.conf [Service] ExecStart= ExecStart=/usr/bin/nm-online -s -q --timeout=5   # cat /etc/systemd/system/NetworkManager-wait-online.service.d/override.conf [Service] ExecStart= ExecStart=/usr/lib/systemd/systemd-networkd-wait-online --timeout=5   # cat /etc/systemd/system/networking.service.d/override.conf [Service] TimeoutStartSec=5 ExecStop= ExecStop=/sbin/ifdown -a --read-environment --exclude=lo --force --ignore-errors

This configuration may affect network interface configuration if DHCP is used. If a network device fails to get configuration from the DHCP server, then the timeout value in the two files above must be increased.

Grub Configuration:

Setting the Grub timeout at 2 seconds with GRUB_TIMEOUT=2 under /etc/default/grub. In conjunction with the GRUB_TIMEOUT_STYLE=countdown parameter, Grub will show the countdown of 2 seconds in the console before booting Ubuntu. Please note that, with this short timeout, the standard Grub method for entering the Grub menu (i.e., SHIFT or Esc) does not work. Function key F4 can be used to enter the Grub menu.

System Services:

docker.service is disabled in the default Ubuntu OS image as it dramatically affects boot time.

The kexec utility can be used to reduce the reboot time. Script /usr/sbin/kexec_reboot is included in the default Ubuntu 20.04 OS image to run corresponding kexec commands.

Copy
Copied!
            

# kexec_reboot

Copy
Copied!
            

/etc/dhcp/dhclient.conf: send vendor-class-identifier "NVIDIA/BF/DP"; interface "oob_net0" { send vendor-class-identifier "NVIDIA/BF/OOB"; }

BlueField DPU may be installed with support for dual boot. That is, two identical images of the BlueField OS may be installed using BFB.

The following is a proposed SSD partitioning layout for 119.24 GB SSD:

Copy
Copied!
            

Device Start End Sectors Size Type /dev/nvme0n1p1 2048 104447 102400 50M EFI System /dev/nvme0n1p2 104448 114550086 114445639 54.6G Linux filesystem /dev/nvme0n1p3 114550087 114652486 102400 50M EFI System /dev/nvme0n1p4 114652487 229098125 114445639 54.6G Linux filesystem /dev/nvme0n1p5 229098126 250069645 20971520 10G Linux filesystem

Where:

  • /dev/nvme0n1p1 – boot EFI partition for the first OS image

  • /dev/nvme0n1p2 – root FS partition for the first OS image

  • /dev/nvme0n1p3 – boot EFI partition for the second OS image

  • /dev/nvme0n1p4 – root FS partition for the second OS image

  • /dev/nvme0n1p5 – common partition for both OS images

For example, the following is a proposed eMMC partitioning layout for a 64GB eMMC:

Copy
Copied!
            

Device Start End Sectors Size Type /dev/mmcblk0p1 2048 104447 102400 50M EFI System /dev/mmcblk0p2 104448 50660334 50555887 24.1G Linux filesystem /dev/mmcblk0p3 50660335 50762734 102400 50M EFI System /dev/mmcblk0p4 50762735 101318621 50555887 24.1G Linux filesystem /dev/mmcblk0p5 101318622 122290141 20971520 10G Linux filesystem

Where:

  • /dev/mmcblk0p1 – boot EFI partition for the first OS image

  • /dev/mmcblk0p2 – root FS partition for the first OS image

  • /dev/mmcblk0p3 – boot EFI partition for the second OS image

  • /dev/mmcblk0p4 – root FS partition for the second OS image

  • /dev/mmcblk0p5 – common partition for both OS images

    Warning

    The common partition can be used to store BFB files that will be used for OS image update on the non-active OS partition.

Installing Ubuntu OS Image Using Dual Boot

Warning

For software upgrade procedure, please refer to section "Upgrading Ubuntu OS Image Using Dual Boot".

Add the values below to the bf.cfg configuration file (see section "bf.cfg Parameters" for more information).

Copy
Copied!
            

DUAL_BOOT=yes

If EMMC size is ≤16GB, dual boot support is disabled by default, but it can be forced by setting the following parameter in bf.cfg:

Copy
Copied!
            

FORCE_DUAL_BOOT=yes

To modify the default size of the /common partition, add the following parameter:

Copy
Copied!
            

COMMON_SIZE_SECTORS=<number-of-sectors>

The number of sectors is the size in bytes divided by the block size (512). For example, for 10GB, the COMMON_SIZE_SECTORS=$((10*2**30/512)).

After assigning size for the /common partition, what remains is divided equally between the two OS images.

Copy
Copied!
            

# bfb-install --bfb <BFB> --config bf.cfg --rshim rshim0

This will result in the Ubuntu OS image to be installed twice on the BlueField DPU.

Warning

For comprehensive list of the supported parameters to customize bf.cfg during BFB installation, refer to section "bf.cfg Parameters".


Upgrading Ubuntu OS Image Using Dual Boot

  1. Download the new BFB to the BlueField DPU into the /common partition. Use bfb_tool.py script to install the new BFB on the inactive BlueField DPU partition:

    Copy
    Copied!
                

    /opt/mellanox/mlnx_snap/exec_files/bfb_tool.py --op fw_activate_bfb --bfb <BFB>

  2. Reset BlueField DPU to load the new OS image:

    Copy
    Copied!
                

    /sbin/shutdown -r 0

    BlueField DPU will now boot into the new OS image.

Use efibootmgr utility to manage the boot order if necessary.

  • Change the boot order with:

    Copy
    Copied!
                

    # efibootmgr -o

  • Remove stale boot entries with:

    Copy
    Copied!
                

    # efibootmgr -b <E> -B

    Where <E> is the last character of the boot entry (i.e., Boot000<E>). You can find that by running:

    Copy
    Copied!
                

    # efibootmgr BootCurrent: 0040 Timeout: 3 seconds BootOrder: 0040,0000,0001,0002,0003 Boot0000* NET-NIC_P0-IPV4 Boot0001* NET-NIC_P0-IPV6 Boot0002* NET-NIC_P1-IPV4 Boot0003* NET-NIC_P1-IPV6 Boot0040* focal0 ....2

Warning

Modifying the boot order with efibootmgr -o does not remove unused boot options. For example, changing a boot order from 0001,0002, 0003 to just 0001 does not actually remove 0002 and 0003. 0002 and 0003 need to be explicitly removed using efibootmgr -B .


© Copyright 2023, NVIDIA. Last updated on Dec 15, 2023.