NVIDIA BlueField DPU BSP v4.5.2 LTS
NVIDIA BlueField BSP v4.5.2

BlueField OOB Ethernet Interface

The BlueField OOB interface is a gigabit Ethernet interface which provides TCP/IP network connectivity to the Arm cores. This interface is named oob_net0 and is intended to be used for management traffic (e.g., file transfer protocols, SSH, etc). The Linux driver that controls this interface is named mlxbf_gige.ko, and is automatically loaded upon boot. This interface can be configured and monitored using of standard tools (e.g., ifconfig, ethtool, etc). The OOB interface is subject to the following design limitations:

  • Only supports 1Gb/s full-duplex setting

  • Only supports GMII access to external PHY device

  • Supports maximum packet size of 2KB (i.e., no support for jumbo frames)

The OOB interface can also be used for PXE boot. This OOB port is not a path for the BlueField boot stream. Any attempt to push a BFB to this port would not work. Refer to "How to use the UEFI boot menu" for more information about UEFI operations related to the OOB interface.

The MAC address to be used for the OOB port is burned into Arm-accessible UPVS EEPROM during the manufacturing process. This EEPROM device is different from the SPI Flash storage device used for the NIC firmware and associated NIC MACs/GUIDs. The value of the OOB MAC address is specific to each platform and is visible on the board-level sticker.

Warning

It is not recommended to reconfigure the MAC address from the MAC configured during manufacturing.

If there is a need to re-configure this MAC for any reason, follow these steps to configure a UEFI variable to hold new value for OOB MAC.:

Note

The creation of an OOB MAC address UEFI variable will override the OOB MAC address defined in EEPROM, but the change can be reverted.

  1. Log into Linux from the Arm console.

  2. Issue the command ls /sys/firmware/efi/efivars to show whether efivarfs is mounted. If it is not mounted, run:

    Copy
    Copied!
                

    mount -t efivarfs none /sys/firmware/efi/efivars

  3. Run:

    Copy
    Copied!
                

    chattr -i /sys/firmware/efi/efivars/OobMacAddr-8be4df61-93ca-11d2-aa0d-00e098032b8c

  4. Set the MAC address to 00:1a:ca:ff:ff:03 (the last six bytes of the printf value).

    Copy
    Copied!
                

    printf "\x07\x00\x00\x00\x00\x1a\xca\xff\xff\x03" > /sys/firmware/efi/efivars/OobMacAddr-8be4df61-93ca-11d2-aa0d-00e098032b8c

  5. Reboot the device for the change to take effect.

To revert this change and go back to using the MAC as programmed during manufacturing, follow these steps:

  1. Log into UEFI from the Arm console, go to "Boot Manager" then "EFI Internal Shell".

  2. Delete the OOB MAC UEFI variable. Run:

    Copy
    Copied!
                

    dmpstore -d OobMacAddr

  3. Reboot the device by running "reset" from UEFI.

  4. Log into Linux from the Arm console.

  5. Issue the command ls /sys/firmware/efi/efivars to show whether efivarfs is mounted. If it is not mounted, run:

    Copy
    Copied!
                

    mount -t efivarfs none /sys/firmware/efi/efivars

  6. Run:

    Copy
    Copied!
                

    chattr -i /sys/firmware/efi/efivars/OobMacAddr-8be4df61-93ca-11d2-aa0d-00e098032b8c

  7. Reconfigure the original MAC address burned by the manufacturer in the format aa\bb\cc\dd\ee\ff. Run:

    Copy
    Copied!
                

    printf "\x07\x00\x00\x00\x00\<original-MAC-address>" > /sys/firmware/efi/efivars/OobMacAddr-8be4df61-93ca-11d2-aa0d-00e098032b8c

  8. Reboot the device for the change to take effect.

The Linux driver for the OOB port supports the handling of some basic ethtool requests: get driver info, get/set ring parameters, get registers, and get statistics.

To use the ethtool options available, use the following format:

Copy
Copied!
            

$ ethtool [<option>] <interface>

Where <option> may be:

  • <no-argument> – display interface link information

  • -i – display driver general information

  • -S – display driver statistics

  • -d – dump driver register set

  • -g – display driver ring information

  • -G – configure driver ring(s)

  • -k – display driver offload information

  • -a – query the specified Ethernet device for pause parameter information

  • -r – restart auto-negotiation on the specified Ethernet device if auto-negotiation is enabled

For example:

Copy
Copied!
            

$ ethtool oob_net0 Settings for oob_net0: Supported ports: [ TP ] Supported link modes: 1000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 1000baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 3 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Link detected: yes

Copy
Copied!
            

$ ethtool -i oob_net0 driver: mlxbf_gige version: firmware-version: expansion-rom-version: bus-info: MLNXBF17:00 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: no

Copy
Copied!
            

# Display statistics specific to BlueField-2 design (i.e. statistics that are not shown in the output of "ifconfig oob0_net") $ ethtool -S oob_net0 NIC statistics: hw_access_errors: 0 tx_invalid_checksums: 0 tx_small_frames: 1 tx_index_errors: 0 sw_config_errors: 0 sw_access_errors: 0 rx_truncate_errors: 0 rx_mac_errors: 0 rx_din_dropped_pkts: 0 tx_fifo_full: 0 rx_filter_passed_pkts: 5549 rx_filter_discard_pkts: 4

The files that control IP interface configuration are specific to the Linux distribution. The udev rules file (/etc/udev/rules.d/92-oob_net.rules) that renames the OOB interface to oob_net0 and is the same for Yocto, CentOS, and Ubuntu:

Copy
Copied!
            

SUBSYSTEM=="net", ACTION=="add", DEVPATH=="/devices/platform/MLNXBF17:00/net/eth[0-9]", NAME="oob_net0"

The files that control IP interface configuration are slightly different for CentOS and Ubuntu:

  • CentOS configuration of IP interface:

    • Configuration file for oob_net0: /etc/sysconfig/network-scripts/ifcfg-oob_net0

    • For example, use the following to enable DHCP:

      Copy
      Copied!
                  

      NAME="oob_net0" DEVICE="oob_net0" NM_CONTROLLED="yes" PEERDNS="yes" ONBOOT="yes" BOOTPROTO="dhcp" TYPE=Ethernet

    • For example, to configure static IP use the following:

      Copy
      Copied!
                  

      NAME="oob_net0" DEVICE="oob_net0" IPV6INIT="no" NM_CONTROLLED="no" PEERDNS="yes" ONBOOT="yes" BOOTPROTO="static" IPADDR="192.168.200.2" PREFIX=30 GATEWAY="192.168.200.1" DNS1="192.168.200.1" TYPE=Ethernet

  • For Ubuntu configuration of IP interface, please refer to section "Default Network Interface Configuration".

© Copyright 2024, NVIDIA. Last updated on Jul 10, 2024.