NVIDIA ConnectX-8 SuperNIC Firmware Release Notes v40.44.0208

Changes and New Features

Info

To generate PLDM packages for firmware updates, users must install and use the MFT version that corresponds with the respective firmware release.

Feature/Change

Description

40.44.0208

General

This is the initial firmware release of NVIDIA® ConnectX®-8 SuperNIC.

ConnectX-8 has the same feature set as ConnectX-7 adapter card. For the list of the ConnectX-7 firmware features, please see ConnectX-7 Firmware Release Notes.

The features described here are new features in addition to the ConnectX-7 set.

Link Speed

NVIDIA® ConnectX®-8 SuperNIC supports 800Gb/s or XDR IB or 2 x 400GbE link speeds.

Note: 800GbE link speed is not supported on a single port.

Planarized Topology Network

ConnectX®-8 SuperNIC uses planarized topology network to reach Extended Data Rate (XDR) performance.

Direct NIC-GPU Datapath

To read/write data directly from the GPU and to overcome grace CPU PCIe bandwidth issue a direct NIC-GPU datapath is required.

To do so, the HCA exposes a side DMA engine as an additional PCIe function which is called “Data Direct”. This additional DMA engine allows vHCA access data buffers using MKEY through it, providing multiple PCIe data path interfaces. Such behavior is needed in a scenario where different memory region requires different PCIe data path, i.e NUMA (Non Uniform Memory Access) systems.

A vHCA is allowed to use a Data Direct function if HCA_CAP.data_direct is set. To use the Data Direct interface, the vHCA should create an MKEY with the data_direct bit set. The MKEY returned enables access through the side DMA engine. The MKEY access mode must be PA.

It supports only the following fields: a, rw, rr, lw, lr, relaxed_ordering_write, relaxed_ordering_read, mkey[7:0], length64, pd, start_addr, len. All other fields are reserved.

Congestion Control

Congestion Control provides performance isolation when multiple applications running on the same cluster. Additionally, it prevents congestion spreading when there is a slow receiver, reduce latency in the cluster, improves fairness, prevents parking-lot effects and packet's drop in lossy networks.

Multiple Encapsulation/Decapsulation Operation on a Packet

This capability enables the encapsulation table to be opened on both the FDB and the NIC tables together.

Crypto Algorithms

Extended the role-based authentication to cover all crypto algorithms. Now the TLS. IPsec. MACsec. GCM, mem2mem, and NISP work when nv_crypto_conf.crypto_policy = CRYPTO_POLICY_FIPS_LEVEL_2, meaning all cryptographic engines can also work in wrapped mode and not only in plaintext mode.

RoCE: Adaptive Timer

Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.

Multiple-Window in DPA Mode

Multi-window capability is now supported in DPA mode.

Doorbell Less QP

The new capability enables the user to send a queue without a doorbell record.

To create a doorbell less QP/SP, set send_dbr_mode = 1 in qp/sq ctx as defined in the PRM.

Packet's Flow Label Fields

The flow_label fields can be set, added or copied from the packet.

ODP Event

The following prefetch fields are available ODP event: pre_demand_fault_pages, post_demand_fault_pages

Jump from NIC_TX to FDB_TX

The user can jump from NIC_TX to FDB_TX table and bypass the ACL table using the 'table_type_valid' and 'table_type' fields available in the steering action (STC) "Jump To Flow" table.

The following are the unsupported features for ConnectX-8 SuperNIC in this firmware version:

  • Zero Touch Tuning (ZTT)

  • Transport Layer Security (TLS) handshake

  • T10 Data Integrity Field (DIF)

  • Static split 8x100G ConnectX-8 to Spectrum-4 with SM modules

  • NC-SI Path-Through

  • Lane margin

  • Segment on PCIe switch

  • Hot reset

  • DRS

  • LAG Bonding with Q-Affinity

  • AER on PCIe switch bridge

  • ISSU

© Copyright 2024, NVIDIA. Last updated on Dec 25, 2024.