ConnectX-4 onwards Adapter Cards Family

Upon first time device burning, the GUIDs, MACs and VPD of the device are required to be set on the flash.

The sections below demonstrate two methods of burning a new ConnectX-4 onwards device in order to set these initial settings. Subsequent firmware updates will not change these settings.

For information regarding GUIDs, MACs and VPD, please refer to Accessing Remote InfiniBand Device by Direct Route MADs.

Method 1: Generating Firmware with Specific GUIDs and MACs and Burning it on the Device

In order to burn a new device, follow the steps below:

1. Disable the Write protection.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr hw set Flash0.WriteProtected=Disabled
           

2. Burn the entire flash.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -i ./ fw-ConnectX4- MCX454_Ax.bin -ocr -ignore_dev_data - allow_psid_change -nofs --yes burn
           

3. Set Write protection

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr hw set Flash0.WriteProtected=Top,8-SubSectors
           

4. Enable flash quad SPI IO operations.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr hw set QuadEn=1
           

Method 2: Generating Firmware Image with Blank GUIDs, Burning and Setting GUIDs on the Device

In order to burn a new device, follow the steps below:

1. Disable the Write protection.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr hw set Flash0.WriteProtected=Disabled
           

2. Burn the entire flash.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -i ./ fw- ConnectX4- MCX454_Ax.bin -ocr -ignore_dev_data - allow_psid_change -nofs --yes burn
           

3. Set device manufacture GUIDs and MACs.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr -guid 0xe41d2d0300570fc0 -mac 0x0000e41d2d570fc0 smg 
           

4. Set device GUIDs and MACs.

   Copy

   Copied!

               
   
               
    # flint -d /dev/mst/mt521_pciconf0 -ocr -guid 0xe41d2d0300570fc0 -mac 0x0000e41d2d570fc0 sg
           

5. Set Write protection on the last sector using flint:

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr hw set Flash0.WriteProtected=Top,8-SubSectors
           

   Note

   The command may vary based on the Flash type used.

   Protection_type can be :

   • 1- Top,8-SubSectors, if it is in [W25QxxBV]

   • 2- Top,1-Sectors, if it is in [MX25L16xxx, N25Q0XX, IS25LPxxx, S25FL256L, MX25Lxxx, W25Qxxx, MX25Uxxx]

6. Enable flash quad SPI IO operations.

   Copy

   Copied!

               
   
               
   # flint -d /dev/mst/mt521_pciconf0 -ocr hw set QuadEn=1
           

   1. To view flash settings:

      Copy

      Copied!

                  
      
                  
      # flint -d /dev/mst/mt521_pciconf0 -ocr hw query
              

   2. To view assigned GUIDs:

      Copy

      Copied!

                  
      
                  
      # flint -d /dev/mst/mt521_pciconf0 -ocr
              

   3. To change a GUID after the initial burn:

      Copy

      Copied!

                  
      
                  
      # flint -d /dev/mst/mt4115_pciconf0 -ocr -guid 0xe41d2d0300570fc0 sg
              

   4. To change a MAC after the initial burn:

      Copy

      Copied!

                  
      
                  
      # flint -d /dev/mst/mt4115_pciconf0 -ocr -mac 0x0000e41d2d570fc0 sg
              

   5. To change a GUID and derive MAC from it after the initial burn, run:

      Copy

      Copied!

                  
      
                  
      # flint -d /dev/mst/mt4115_pciconf0 -ocr -uid 0xe41d2d0300570fc0 sg