Document Revision History

2.7

August 06, 2020

Added:

• Section "Events"

• Section "WJH Category Distribution"

• Section "Services"

• Section "Configuration Changes"

• Section "WJH Filtering"

• Section "Categories Distribution"

• Section "Events Distribution Per Switch"

• Section "Connectivity Check"

• Section "Cables"

Updated:

• Section "Navigator Tabs"

• Section "Monitoring Window"

• Section "General Dashboard"

• Section "Network Health"

2.6

May 26, 2020

Added:

• Section "NEO Health Monitoring"

• Section "Time-based WJH Events"

• Section "Compare Configuration"

• Section "Auto-Provisioning"

• Section "Telemetry Agent Supported Counters Per Profile"

Updated:

• Section "Installation Prerequisites"

• Section "Ports Used by Mellanox NEO Application"

• Section "Installing NEO for High Availability"

• Section "Installing Mellanox NEO as Docker Container"

• Section "Sites" with Network Map view

• Section "Uninstalling Mellanox NEO as Docker Container"

• Note under Available Service Element Operations → Idle → Clean-up

• Section "Adding Devices"

• Section "Removing Devices"

• Section "Tasks Tab"

• Section "Built-in Tasks"

• Section "Discovery"

• Section "Backup and Restore"

• Section "Modifying Management IP Address"

• Section "Configuring Email Notifications According to Event Severity"

• Section "Configuring Mellanox Onyx Switch for Sending Traps to Mellanox NEO"

• Section “Configuring Host for LLDP Discovery”

• Section "Setting NEO SNMP Trap Protocol Registration"

2.5

November 17, 2019

• Added the following sections:

  • Built-in Tasks

  • Setting NEO SNMP Trap Protocol Registration

• Updated the following sections:

  • Configuring Mellanox Onyx Switch for Sending Traps to Mellanox NEO

  • Logs

  • Local Mode

October 2, 2019

• Added two items to Known Issues section of Release Notes:

  • Running WJH on a Cumulus switch is not supported. (Up to the release of NEO v2.5, no Cumulus version that supports WJH existed.)

  • If a device (Linux host or switch) is removed from NEO while some Mellanox switches are running telemetry, then all the telemetry sessions running on these switches will be stopped.

September 26, 2019

• Incorporated the Quick Start Guide document into the User Manual.

• Added a new Element Operation (Clean-up) to table Available Service Elements' Operations

• Added What-Just-Happened (WJH) Device Events. See Device Events

• Added Prism AHV Configuration

• Updated Virtualization Settings

• Added What Just Happened Filtering

• Added Uninstalling NEO as a Docker Container

• Updated the Bring Up wizard screenshots due to a new look-and-feel interface. See Bring Up Wizard

• Updated the Create a New Session section, updated the profiles list

• Updated Mellanox NEO/Nutanix Prism Plug-in

• Updated What Just Happened?

• Updated NEO VXLAN Templates

• Removed the switch limitation from section Limitations.

• Removed section DCI Support from Mellanox NEO/Nutanix Prism Plug-in

2.4

April 30, 2019

Added the following sections:

• Telemetry Snapshots

• Virtualization Settings

• Generate Dump

• Bring-up Wizard and its subsections

Updated the following sections:

• “Main Tabs/Categories/Navigator Buttons” and its subsections

• “Services” and its subsections

• “Managed Elements” and its subsections

• "Monitoring”

• "Configuring Windows Host for Basic Authentication"

• What Just Happened Overview

• Network Map and its subsections

• Updated the Network Notifications Icon screenshot: no eco mode

2.3.1

March 3, 2019

Updated the following section:

• “Configuring Host for LLDP Discovery”

January 31, 2019

No changes have been performed in this release