Upgrading UFM on Docker Container

Warning

Upgrade the UFM container based on the existing UFM configuration files that are mounted on the server. It is important to use that same directory as a volume for the UFM installation command.
In the below example /opt/ufm_files is used.

Upgrading UFM on Docker Container in Standalone Mode

Stop the UFM Enterprise service. Run:

Copy
Copied!

            
            systemctl stop ufm-enterprise

Remove the existing docker image. Run:

Copy
Copied!

            
            docker rmi mellanox/ufm-enterprise:latest

Load the new UFM Enterprise docker image. Run:

Copy
Copied!

            
            docker pull mellanox/ufm-enterprise:latest

Run the docker upgrade command:

Copy
Copied!

            
            docker run -it --name=ufm_installer --rm \
-v /var/run/docker.sock:/var/run/docker.sock \
-v /etc/systemd/system/:/etc/systemd_files/ \
-v /opt/ufm/files/:/opt/ufm/shared_config_files/ \
mellanox/ufm-enterprise:latest --upgrade

Reload system manager configuration:

Copy
Copied!

            
            systemctl daemon-reload

Start UFM Enterprise service:

Copy
Copied!

            
            systemctl start ufm-enterprise

Upgrading UFM Container in High Availability Mode

Warning

As of UFM version 6.14.0, UFM upgrade on HA supports in-service upgrade, meaning UFM can continue running during the steps of the upgrade, and there is no need to stop UFM before the upgrade (although this is also supported).

Remove the old docker image from the standby server. Run:

Copy
Copied!

            
            Stand-by# docker rmi mellanox/ufm-enterprise:latest

Pull the new UFM Enterprise docker image on the standby server. Run:
Copy

Copied!
```
            
            docker pull mellanox/ufm-enterprise:latest
        
```
Warning

At this stage, the UFM container has been updated with the latest code. The UFM data, however, will be updated during the next UFM run.
Perform a failover to start UFM on the upgraded node. On the master node, run:
Copy

Copied!
```
            
            ufm_ha_cluster failover
        
```
Warning

When UFM starts, it will automatically update the UFM configuration.
Repeat steps 1-2 on the un-upgraded node (previous Master node).

Download and extract the latest UFM HA package. Run:

Copy
Copied!

            
            wget https://www.mellanox.com/downloads/UFM/ufm_ha_5.1.1-6.tgz

Install the extracted UFM HA package:

Warning

In the below command, please modify the partition name based on the already configured DRBD partition.
Copy

Copied!
```
            
            ./install.sh -l /opt/ufm/files/ -d /dev/sda5 -p enterprise
        
```
Configure HA. There are two methods:
- Configure HA with SSH Trust - Requires passwordless SSH connection between the servers.
- Configure HA without SSH Trust - Does not require passwordless SSH connection between the servers, but asks you to run configuration commands on both servers.
Configure HA with SSH Trust
1. 1. On the master server only, configure the HA nodes. To do so, from /tmp, run the configure_ha_nodes.sh command as shown in the below example
    Copy
    
    Copied!
    
    configure_ha_nodes.sh --cluster-password 12345678 \ --local-primary-ip 10.10.50.1 \ --peer-primary-ip 10.10.50.2 \ --local-secondary-ip 192.168.10.1 \ --peer-secondary-ip 192.168.10.2 \ --no-vip
    Warning
    
    The script configure_ha_nodes.sh is is located under /usr/local/bin/, therefore, by default, you do not need to use the full path to run it.
    
    Warning
    
    The --cluster-password must be at least 8 characters long.
    
    Warning
    
    To set up a Virtual IP for UFM and gain access to UFM through this IP, regardless of which server is running UFM, you may employ the --no-vip OR --virtual-ip command and provide an IP address as an argument. This can be achieved by navigating to https://<Virtual-IP>/ufm on your web browser.
    
    Warning
    
    When using back-to-back ports with local IP addresses for HA sync interfaces, ensure that you add your IP addresses and hostnames to the /etc/hosts file. This is needed to allow the HA configuration to resolve hostnames correctly based on the IP addresses you are using.
    
    Warning
    
    configure_ha_nodes.sh requires SSH connection to the standby server. If SSH trust is not configured, then you are prompted to enter the SSH password of the standby server during configuration runtime
  2. Depending on the size of your partition, wait for the configuration process to complete and DRBD sync to finish.
Configure HA without SSH Trust
If you cannot establish an SSH trust between your HA servers, you can use ufm_ha_cluster directly to configure HA. To configure HA, follow the below instructions:

Warning

Please change the variables in the commands below based on your setup.
1. 1. [On Standby Server] Run the following command to configure Standby Server:
    Copy
    
    Copied!
    
    ufm_ha_cluster config -r standby \ --local-primary-ip 10.10.50.1 \ --peer-primary-ip 10.10.50.2 \ --local-secondary-ip 192.168.10.1 \ --peer-secondary-ip 192.168.10.2 \ --hacluster-pwd 123456789 \ --no-vip
  2. [On Master Server] Run the following command to configure Master Server:
    Copy
    
    Copied!
    
    ufm_ha_cluster config -r master --local-primary-ip 10.10.50.1 \ --peer-primary-ip 10.10.50.2 \ --local-secondary-ip 192.168.10.1 \ --peer-secondary-ip 192.168.10.2 \ --hacluster-pwd 123456789 \ --no-vip
You must wait until after configuration for DRBD sync to finish depending on the size of your partition.

Start UFM HA cluster. Run:

Copy
Copied!

            
            ufm_ha_cluster start

On This Page

Upgrading UFM on Docker Container

Upgrading UFM on Docker Container in Standalone Mode

Upgrading UFM Container in High Availability Mode