NVIDIA UFM Enterprise User Manual v6.15.1
NVIDIA UFM Enterprise User Manual v6.15.1

Appendix – UFM Event Forwarder

UFM Event Forwarder enables streaming of UFM events via FluentBit forwarder plugin to any external destination.

To deploy the UFM Event Forwarder on a Linux machine:

  1. Connect to the Linux host via SSH.

  2. Ensure the docker is installed on the host. Run:

    Copy
    Copied!
                

    # docker –version

  3. Make sure that the docker service is up and running. If it is not, start the docker service. Run:

    Copy
    Copied!
                

    # sudo service docker start

  4. Pull the UFM Event Forwarder image. Run:

    Copy
    Copied!
                

    # sudo docker pull mellanox/ufm-events-forwarder

    Alternatively, if you do not have internet connection, contact NVIDIA Support to receive the UFM Event Forwarder docker image and load it to the host. Run:

    Copy
    Copied!
                

    # sudo cp <ufm-events-forwarder image path> /tmp/ # sudo docker load -i /tmp/<image name>

  5. If you are running in HA mode, repeat step 1-4 on the standby node.

    Warning

    Steps 6-9 should only be configured on the master node.

  6. Enable the event-forwarder in main UFM config file. Run:

    Copy
    Copied!
                

    # vim /opt/ufm/files/conf/gv.cfg [Plugins] events_forwarder_enabled=true

  7. Configure UFM to send events via syslog to the FluentBit event forwarder in gv.cfg.

    Copy
    Copied!
                

    [Logging] syslog_addr=127.0.0.1:5140 syslog = true ufm_syslog = true event_syslog = true syslog_level = <severity>

    Warning

    <severity> may be set to any of the following values: CRITICAL, ERROR, WARNING, INFO, or DEBUG.

  8. Configure the destination IP and port for the FluentBit event forwarder (requires Python 3):

    Copy
    Copied!
                

    # python /opt/ufm/scripts/events-forwarder/configure-fluent-bit.pyc -i <IP> -p <port>

    Alternatively, if you have Python 2:

    Copy
    Copied!
                

    # /opt/ufm/venv_ufm/bin/python /opt/ufm/scripts/events-forwarder/configure-fluent-bit.pyc -i <IP> -p <port>

  9. Start UFM. Run:

    Copy
    Copied!
                

    # /etc/init.d/ufmd start

    Alternatively, if you are running in HA:

    Copy
    Copied!
                

    # /etc/init.d/ufmha start

  10. Verify that UFM Event Forwarder is running successfully. Run:

    Copy
    Copied!
                

    # /etc/init.d/ufmd start ufmd start Starting opensm: [ OK ] Starting MySQL: [ OK ] Restarting httpd: [ OK ] Starting snmpd: [ OK ] Starting UFM main module: [ OK ] Starting Events-Forwarder: [ OK ] Starting Daily Report: [ OK ] Starting UnhealthyPorts: [ OK ] Starting ibpm: [ OK ]

    Warning

    Make sure the status of Events-Forwarder is OK.

Stopping UFM will also stop the Event Forwarder.

Copy
Copied!
            

# /etc/init.d/ufmd stop ufmd stop Stopping ibpm: [ OK ] Stopping Daily Report: [ OK ] Stopping UnhealthyPorts: [ OK ] Stopping Events-Forwarder: [ OK ] Stopping UFM main module: [ OK ] Stopping MySQL: [ OK ] Stopping OpenSM: [ OK ]

After configuration, the Event Forwarder should always be running on the active node only. After a failover, for example, it will be stopped on the old master and will be started on the new active node.

If the destination IP and port are reconfigured (step 8), the Event Forwarder container should be restarted automatically with the newly applied configuration.

© Copyright 2023, NVIDIA. Last updated on Dec 19, 2023.