Cable Info

Telemetry supports the following field list for cable information.

node_guid

port_guid

sys_image_guid

Port

aport

Lid

node_type

port_type

num_planes

Port_Name

Vendor

vendor_oui

PN

SN

Rev

smf_length

LengthCopperOrActive

Identifier

cable_identifier

Connector

Type

ib_compliance_code

length

length_by_prtl

length_by_reg

cable_type

SupportedSpeedDesc

Temperature

PowerClass

CDREnableTxRx

tx_cdr_enable

rx_cdr_enable

cable_tx_equalization

cable_rx_amp

OutputEmp

cable_rx_emphasis

cable_rx_post_emphasis

fw_version

mi_rx_power_type

HighTemperatureAlarm

LowTemperatureAlarm

HighTemperatureWarning

LowTemperatureWarning

InitializationFlagComplete

HighSupplyVoltageAlarm

LowSupplyVoltageAlarm

HighSupplyVoltageWarning

LowSupplyVoltageWarning

diag_supply_voltage

transmitter_technology

ActiveWavelengthControl

CooledTransmitterDevice

ActivePinDetector

TunableTransmitter

ExtendedSpecificationComplianceCodes

temperature_high_th

temperature_low_th

WarnTemperatureHighThresh

WarnTemperatureLowThresh

voltage_high_th

voltage_low_th

WarnVoltageHighThresh

WarnVoltageLowThresh

rx_power_high_th

rx_power_low_th

tx_power_high_th

tx_power_low_th

tx_bias_high_th

tx_bias_low_th

date_code

Lot

RXOutputDisable

TXAdaptiveEqualizationEnable

max_power

cable_vendor

ib_width

wavelength

ethernet_compliance_code

cable_breakout

tx_cdr_cap

rx_cdr_cap

memory_map_rev

wavelength_tolerance

module_st

rx_output_valid

rx_input_valid

active_set_host_compliance_code

active_set_media_compliance_code

tx_input_freq_sync

error_code

did_cap

cdr_vendor

max_fiber_length

dp_fw_fault

mod_fw_fault

tx_fault

rx_output_valid_change

rx_input_valid_change

temperature_alarm_and_warning

voltage_alarm_and_warning

tx_los

tx_cdr_lol

tx_ad_eq_fault

tx_power_hi_al

tx_power_lo_al

tx_power_hi_war

tx_power_lo_war

tx_bias_hi_al

tx_bias_lo_al

tx_bias_hi_war

tx_bias_lo_war

rx_los

rx_cdr_lol

rx_power_hi_al

rx_power_lo_al

rx_power_hi_war

cable_temperature

link_partner

HighRX[1-4]PowerAlarm

HighRX[1-4]PowerWarning

HighTX[1-4]BiasAlarm

HighTX[1-4]BiasWarning

HighTX[1-4]PowerAlarm

HighTX[1-4]PowerWarning

LengthOM[1-5]

LowRX[1-4]PowerAlarm

LowRX[1-4]PowerWarning

LowTX[1-4]BiasAlarm

LowTX[1-4]BiasWarning

LowTX[1-4]PowerAlarm

LowTX[1-4]PowerWarning

RX[1-4]CDRLOL

RX[1-4]LatchedLossIndicator

TX[1-4]AdaptiveEqualizationFaultIndicator

TX[1-4]AdaptiveEqualizationFreeze

TX[1-4]CDRLOL

TX[1-4]LatchedLossIndicator

cable_attenuation_2_5g

cable_attenuation_[5,7,12,25]g

dp_st_lane[0-3]

nbr_250

node_guid_plane_[0-3]

port_num_plane_[0-3]

rx_power_lane[0-7]

tx_bias_lane[0-7]

tx_power_lane[0-7]

• mem_buffers – relatively temporary storage for raw disk blocks that should not become exceptionally large

• mem_cached – memory in the pagecache (diskcache) minus SwapCache—does not include SwapCached

• mem_free – sum of free lowmem and free highmem

• mem_swap_chache – memory that was once swapped out is swapped back in but is still kept in the swap file

• mem_total – total usable RAM

• mlnx:total_read_time – time spent on reading all counters

• clx_cpu_load

• clx_pid

• clx_res_mem

• clx_shr_mem

• clx_virt_mem