Controller Area Network (CAN)

Applies to: Jetson AGX Orin, Jetson Orin NX, Jetson Orin Nano, Jetson Xavier NX series, and Jetson AGX Xavier series.

This topic describes the Time Triggered CAN (TTCAN) controller on the Always-On block of the NVIDIA SoC, and how to use it in user space.

Important Features

The Time Triggered CAN controller has several important features:

  • It supports standard and extended frame transmission.

  • Its CAN bus bit rate can be configured from 10 kbps to 1 Mbps.

  • It supports CAN FD mode with a maximum data bit rate of 15 Mbps. All types of transceivers can achieve a 5 Mbps data bit rate.

  • It can deliver higher data bit rates if you configure the TDCR (Transmission Delay Compensation Register) through its user space sysfs node.

Jetson Platform Details

The following table shows details of the CAN implementation on each supported platform.

Property Jetson Orin NX and Nano Jetson AGX Orin Jetson Xavier NX series Jetson AGX Xavier series
Number of controllers 1 2 1 2
Controller base address mttcan@c310000 mttcan@c310000
mttcan@c320000
mttcan@c310000 mttcan@c310000
mttcan@c320000
Pins on Jetson carrier board J17:
 CAN_RX: [1]
 CAN_TX: [2]
J30 (40-pin header):
 CAN0_DIN: [29]
 CAN0_DOUT: [31]
 CAN1_DIN: [37]
 CAN1_DOUT: [33]
J17:
 CAN_RX: [1]
 CAN_TX: [2]
J30 (40-pin header):
 CAN0_DIN: [29]
 CAN0_DOUT: [31]
 CAN1_DIN: [37]
 CAN1_DOUT: [33]
Pinmux can0_din Addr: 0x0c303018
Value: 0xc458
Addr: 0x0c303018
Value: 0xc458
Addr: 0x0c303018
Value: 0xc458
Addr: 0x0c303018 Value: 0xc458
Pinmux can0_dout Addr: 0x0c303010
Value: 0xc400
Addr: 0x0c303010
Value: 0xc400
Addr: 0x0c303010
Value: 0xc400
Addr: 0x0c303010
Value: 0xc400
Pinmux can1_din n/a Addr: 0x0c303008
Value: 0xc458
n/a Addr: 0x0c303008
Value: 0xc458
Pinmux can1_dout n/a Addr: 0x0c303000
Value: 0xc400
n/a Addr: 0x0c303000
Value: 0xc400
Default pin configuration SFIO: CAN functionality GPIO SFIO: CAN functionality GPIO

Enabling CAN

The interface from an NVIDIA® Jetson™ device to CAN requires a transceiver that supports a minimum of 3.3  V and a transfer rate based on the Jetson platform’s specifications. See the section Important Features for details.

NVIDIA recommends the WaveShare SN65HVD230 CAN board for development systems. Your choice of transceiver for production devices depends on your application’s requirements.

Make the following connections from the transceiver to the Jetson carrier board:

  • Transceiver Rx to Jetson CAN_RX

  • Transceiver Tx to Jetson CAN_TX

  • Transceiver VCC to Jetson 3.3V pin

  • Transceiver GND to Jetson GND pin

This diagram shows an example of a correct connection:

A CAN network correctly connected

Kernel DTB

By default, "+" nodes are enabled in the kernel device tree:

mttcan@c310000 {
    status = "okay";
};
mttcan@c320000 {
    status = "okay";
};

You can also check this field from user space:

$ cat /proc/device-tree/mttcan\@c310000/status

Pinmux

Make sure that the pinmux register settings are applied as shown by the table in the section Jetson Platform Details.

Pinmux can be updated in several ways:

  • Use a BusyBox devmem tool to write to hardware registers. Changes will persist only until the system is rebooted.

    Enter this command to install BusyBox:

    $ sudo apt-get install busybox
    

    This example writes the value 0x458 to register address 0x0c303020:

    $ busybox devmem 0x0c303020 w 0x458
    
  • Update the respective platform pinmux configuration files and flash the updated files.

  • See Running Jetson-IO, in the topic Configuring the Jetson Expansion Headers, for information about how to enable pins.

Kernel Drivers

Load all of the necessary CAN kernel drivers in the order shown.

To load the CAN kernel drivers

  1. Insert the CAN BUS subsystem support module:

    $ modprobe can
    

    or

    $ insmod /lib/modules/5.x.xxx-tegra/kernel/net/can/can.ko
    
  2. Insert the raw CAN protocol module (CAN-ID filtering):

    $ modprobe can_raw
    

    or

    $ insmod /lib/modules/5.x.xxx-tegra/kernel/net/can/can-raw.ko
    
  3. Add real CAN interface support (for Jetson, mttcan):

    $ modprobe mttcan
    

    or

    $ insmod /lib/modules/5.x.xxx-tegra/kernel/drivers/net/can/mttcan/native/mttcan.ko
    

Managing the Network

To use the network, you must first bring up CAN devices on the network and install a group of CAN utilities to use for testing. Then you can transfer packets and debug the network interface if necessary.

To set the interface properties

  • These example commands set the network interface to use FD (Flexible Data) mode with a bus bit rate of 500  kbps and a data bit rate of 1 Mbps, enter the commands:

    $ ip link set can0 up type can bitrate 500000 dbitrate 1000000 berr-reporting on fd on
    $ ip link set can1 up type can bitrate 500000 dbitrate 1000000 berr-reporting on fd on
    

To install the CAN utilities

  • Enter the command:

    $ sudo apt-get install can-utils
    

To transfer packets

  • This example command transfers a packet to can0 with CAN ID 123 and data ‘abcdabcd’:

    $ cansend can0 123#abcdabcd
    
  • This example command receives a packet from any CAN node connected to the bus:

    $ candump -x any &
    
  • This example command transfers an FD frame to can0 with CAN ID 123, flag bit 1, and data ‘abcdabcd’:

    $ cansend can0 123##1abcdabcd
    

For more information about the use of cansend, enter this command:

$ cansend --help

You can use other tools, such as cangen, for different filtering options.

Debug Methods

This section discusses methods of debugging CAN network problems.

Loopback test

You can perform a loopback test to determine whether the controller is working.

To perform a loopback test

  1. Short the Tx and Rx pins of the Jetson carrier board’s CAN0.

  2. Enable the CAN drivers. (See Kernel Drivers for more information.)

    $ ip link set can0 type can bitrate 500000 loopback on
    $ ip link set can0 up
    $ candump can0 &
    $ cansend can0 123#abcdabcd
    

If the loopback test is successful, the last command displays this:

can0 123 [4] AB CD AB CD
can0 123 [4] AB CD AB CD

Other Methods

Several other debugging techniques may be useful in appropriate cases:

  • If a loopback test shows that the controller is working correctly and you are still not able to send or receive packets, try reconnecting the transceiver and confirm that the connections are correctly made.

  • Check whether all of the steps necessary to enable CAN were done properly.

  • Connect an oscilloscope and see whether the bus is behaving properly.

  • If the device logs a “No buffer space available” message during send, enter this command to use the polling mechanism:

    $ cangen -L 8 can0 -p 1000
    

Obtaining Higher Bit Rates

You can obtain higher data bit rates by configuring the TDCR (Transmission Delay Compensation Register) through its user space sysfs node.

Make sure that the transceiver being used is able to support higher bit rates.

To configure the TDCR for higher bit rates

  1. Enter the command:

    $ echo 0x600 > /sys/devices/c320000.mttcan/net/can1/tdcr
    
  2. Bring up the CAN interface on the network and transfer packets. See Managing the Network for more information.

Changing the CAN parent clock on T194 platforms

Applies to: Jetson Xavier NX series and Jetson AGX Xavier series devices only

On devices based on the NVIDIA T194 SoC, the CAN parent clock is PLL_C. The PLL_C clock’s core clock frequency is set to 34 MHz.

To set a higher clock frequency or to obtain a bit rate of exactly 1 Mbps, enable the PLLAON clock and make it the parent clock of MTTCAN.

For information about using PLLAON as the parent clock of MTTCAN, see Configuring Clocks in the topic Clocks.

Changing the CAN Clock Rate

The mttcan kernel driver sets the CAN clock rate. Follow the instructions in Obtaining the Kernel Sources with Git in the topic Kernel Customization to obtain kernel source code. Update the clock rate in the mttcan driver as in this code snippet:

.set_can_core_clk = true,
.can_core_clk_rate = 50000000, // modify here (in Hz)
.can_clk_rate = 200000000,     // four times of core clock rate

The default CAN clock rate is:

  • NVIDIA® Jetson Xavier™ NX series: 50 MHz

  • NVIDIA® Jetson AGX Xavier™ series: 50 MHz

To check the clock rate set in software via user space sysfs node, enter the command:

$ cat /sys/kernel/debug/bpmp/debug/clk/can0/rate

To check actual clock rate set in hardware via user space sysfs node, enter the command:

$ cat /sys/kernel/debug/bpmp/debug/clk/can0/pto_counter