image image image image image

On This Page

Network Time Protocol (NTP) is a networking protocol for clock synchronization between computer systems over variable-latency data networks. NTP is intended to synchronize all participating computers to within a few milliseconds of Coordinated Universal Time (UTC) and is designed to mitigate the effects of variable network latency. NTP can usually maintain time to within tens of milliseconds over the public Internet, and can achieve better than one millisecond accuracy in local area networks under ideal conditions.

NTP Authenticate

When authentication of incoming NTP packets is enabled, the gateway ensures that they come from an authenticated time source before using them for time synchronization on the gateway. Authentication keys are created and added to the trusted list.

To add a key to be used for authentication, take the following steps.

  1. Create the key. 

    gateway (config)# ntp authentication-key 1 md5 password

  2. Add the key to the trusted list.

    gateway (config)# ntp trusted-key 1

  3. Assign the key to the server/peer.

    gateway (config)# ntp server 10.34.1.1 keyID 1

NTP Authentication Key

An authentication key may be created and used to authenticate incoming NTP packets. For the key to be used, make sure the following is in place.

  1. It should be shared with the NTP server/peer sending the NTP packet.
  2. It should be added to the trusted list.

  3. NTP authenticate should be enabled on the system


NTP Commands


clock set


clock set <hh:mm:ss> [<yyyy/mm/dd>]

Sets the time and date.

Syntax Descriptionhh:mm:ssTime
yyyy/mm/ddDate
DefaultN/A
Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # clock set 23:23:23 2010/08/19

Related Commandsshow clock
NotesIf not specified, the date will be left the same.

clock timezone


clock timezone [<zone-word> [<zone-word> [<zone-word>] [<zone-word>]]]
no clock timezone

Sets the system time zone. The time zone may be specified in one of three ways:

  • A nearby city whose time zone rules to follow. The system has a large list of cities which can be displayed by the help and completion system. They are organized hierarchically because there are too many of them to display in a flat list. A given city may be required to be specified in two, three, or four words, depending on the city
  • An offset from UTC. This will be in the form UTC-offset UTC, UTC-offset UTC+<0-14>, UTC-offset UTC-<1-12>
  • UTC (Universal Time, which is almost identical to GMT), and this is the default time zone

The no form of the command resets time zone to its default (GMT).

Syntax Descriptionzone-word

Possible forms this could take include: continent, city, continent, country, city, continent, region, country, city, ocean, and/or island.

DefaultGMT
Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # clock timezone America North United_States Other New_York

Related Commandsshow clock
Notes

ntp 


ntp {disable | enable | {peer | server} <IP address> [version <number> | disable]}
no ntp {disable | enable | {peer | server} <IP address> [version <number> | disable]}

Configures NTP.
The no form of the command negates NTP options.

Syntax Description

disable

Disables NTP.

enableEnables NTP.
peer | serverConfigures an NTP peer or server node.
IP addressIPv4 or IPv6 address.
version <number>

Specifies the NTP version number of this peer.
Possible values: 3 or 4

Default

NTP is enabled
NTP version number is 4

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # no ntp peer 192.168.10.24 disable

Related Commands
Notes

ntpdate


ntpdate <ip-address>

Configures the system clock using the specified SNTP server.

Syntax Description

ip-address

IP address of SNTP server.

Default

N/A

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntpdate 192.168.10.10
26 Feb 17:25:40 ntpdate[15206]: adjust time server 192.168.10.10 offset -0.000092 sec

Related Commands
NotesThis is a one-time operation and does not cause the clock to be kept in sync on an ongoing basis. It will generate an error if SNTP is enabled since the socket it requires will already be in use.

ntp authenticate


ntp authenticate
no ntp authenticate

Enables NTP authentication.
The no form of the command disables NTP authentication.

Syntax Description

N/A

Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp authenticate

Related Commands
Notes

ntp authentication-key


ntp authentication-key <key-id> <encrypt-type> [<password>]
no ntp authentication-key <key-id>

Enables NTP authentication.
The no form of the command disables NTP authentication.

Syntax Description

key-id

Specifies a key ID, whether existing or a new one to be added.
Range: 1-65534

encrypt-typeSpecifies encryption type to use (md5, or sha1)
passwordPassword string
Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp authentication-key 123 md5 examplepass
gateway (config) # ntp authentication-key 1234 sha1
Password: **
Confirm: **

Related Commands
NotesIf a password is not entered, a prompt appears requiring that a password is introduced.

ntp peer disable


ntp peer <ip-address> disable
no ntp peer <ip-address> disable

Temporarily disables this NTP peer.
The no form of the command enables this NTP peer.

Syntax Description

ip-address

IP address of the peer.

Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp peer 10.10.10.10 disable

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7'.)
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen.

ntp peer keyID


ntp peer <ip-address> keyID <key-id>
no ntp peer <ip-address> keyID <key-id>

Specifies the KeyID of the NTP peer.
The no form of the command removes key ID configuration from the NTP peer.

Syntax Description

ip-address

IP address of the peer.

key-idRange: 1-65534
Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp peer 10.10.10.10 keyID 120

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7'.)
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen.

ntp peer version


ntp peer <ip-address> version <ver-num>
no ntp peer <ip-address> version <ver-num>

Specifies the NTP version number of this peer.
The no form of the command defaults NTP to version 4.

Syntax Description

ip-address

IP address of the peer.

ver-num

NTP version.
Possible values: 3 or 4

Default

4

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp peer 10.10.10.10 version 4

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7')
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen.

ntp server disable


ntp server <ip-address> disable
no ntp server <ip-address> disable

Temporarily disables this NTP server.
The no form of the command enables this NTP server.

Syntax Description

ip-address

IP address of the peer.

Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp server 10.10.10.10 disable

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7'.)
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen.

ntp server keyID


ntp server <ip-address> keyID <key-id>
no ntp server <ip-address> keyID <key-id>

Specifies the KeyID of the NTP server.
The no form of the command removes key ID configuration from the NTP server.

Syntax Description

ip-address

IP address of the peer.

key-idRange: 1-65534
Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp server 10.10.10.10 keyID 120

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7'.)
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen.

ntp server-role disable


ntp server-role disable
no ntp server-role disable


Disables the gateway's default ability to function as an NTP server.
The no form of the command restores the gateway's ability to function as an NTP server.

Syntax Description

N/A

Default

N/A

Configuration ModeConfigure terminal
History

8.0.0100

RoleAdmin
Example

gateway (config) # ntp server-role disable

Related Commandsshow ntp
Notes

This command is configurable.

ntp server trusted-enable


ntp server <ip-address> trusted-enable
no ntp server <ip-address> trusted-enable

Trusts this NTP server; if authentication is configured this will additionally force all time updates to only use trusted servers.
The no form of the command removes trust from this NTP server.

Syntax Description

ip-address

IP address of the peer.

Default

N/A

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp server 10.10.10.10 trusted-enable

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7'.)
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen.
  • NTP trusted servers can be used as a mitigation for Sybil attacks which is a vulnerability caused by NTP peers sharing the same NTP key base. This mitigation adds the concept of trusted servers which if enabled in conjunction with NTP authentication ensures that time information will only be obtained from trusted servers.

ntp server version


ntp server <ip-address> version <ver-num>
no ntp server <ip-address> version <ver-num>

Specifies the NTP version number of this server.
The no form of the command defaults NTP to version 4.

Syntax Description

ip-address

IP address of the peer.

ver-num

NTP version.
Possible values: 3 or 4

Default

4

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp server 10.10.10.10 version 4

Related Commands
Notes
  • IP addresses must be in IPv4 format (e.g., '192.168.0.1') or IPv6 format with scope zone ID for IPv6 link-local addresses (e.g., '2001:db8:701f::8f9' or 'fe80::21c:23f:ec1:4fb%7')
  • The length of a hostname is limited to 255 characters. Each label (node delimited by a dot in the hostname) is limited to 63 characters and may contain letters, numbers and hyphens ('-'), but may not begin with a hyphen

ntp trusted-key


ntp trusted-key <key(s)>
no ntp trusted-key <key(s)>

Adds one or more keys to the trusted key list.
The no form of the command removes keys from the trusted key list.

Syntax Description

key(s)

Range: 1-65534

Default

Disabled

Configuration Modeconfig
History

8.0.0100

Example

gateway (config) # ntp trusted-key 1,3,5
gateway (config) # ntp trusted-key 1-5

Related Commands
Notes

Keys may be separated with commas without any space, or they may be set as a range using a hyphen.

show clock


show clock

Displays the current system time, date and time zone.

Syntax Description

N/A

Default

N/A

Configuration ModeAny command mode
History

8.0.0100

Example

gateway (config) # show clock


Time: 02:48:41
Date: 2018/1/1
Time zone: UTC (Etc/UTC)
UTC offset: same as UTC
Related Commands
Notes


show ntp 


show ntp

Displays the current NTP settings.

Syntax Description

N/A

Default

N/A

Configuration ModeAny command mode
History

8.0.0100

Example

gateway (config)# show ntp

NTP is administratively            : enabled
NTP Authentication administratively: disabled
NTP server role                    : enabled

Clock is synchronized:
  Reference: 10.7.7.134
  Offset   : -0.038 ms

Active servers and peers:
  10.7.7.134:
    Conf Type          : serv
    Status             : sys.peer(*)
    Stratum            : 3
    Offset(msec)       : -0.038
    Ref clock          : 192.14.55.225
    Poll Interval (sec): 128
    Last Response (sec): 101
    Auth state         : none

Related Commands
Notes


show ntp configured


show ntp configured

Displays NTP configuration.

Syntax Description

N/A

Default

N/A

Configuration ModeAny command mode
History

8.0.0100

Example

gateway (config) # show ntp configured


NTP enabled: yes
NTP Authentication enabled: no
NTP peer 0.us.pool.ntp.org # Hostname peer configuration
 Resolved as: 45.79.111.114
 Enabled: yes
 NTP version: 4
 Key ID: none
NTP peer 2.3.1.3 # IP peer configuration
 Enabled: yes
 NTP version: 4
 Key ID: none
NTP server vnc23 # Hostname server configuration
 Resolved as: 10.7.2.23
 Enabled: yes
 NTP version: 4
 Key ID: none
 Trusted: no
NTP server 1.2.3.4 # IP server configuration
 Enabled: yes
 NTP version: 4
 Key ID: none
 Trusted: no
NTP server idontexist (DNS resolution failed. Reset or reconfigure NTP to try again)
 Enabled: yes
 NTP version: 4
 Key ID: none
 Trusted: no
Related Commands
Notes


show ntp keys


show ntp configured

Displays NTP keys.

Syntax Description

N/A

Default

N/A

Configuration ModeAny command mode
History

8.0.0100

Example

gateway (config) # show ntp keys

NTP Key 1
 Trusted: yes
 Encryption Type: MD5
NTP Key 2
 Trusted: yes
 Encryption Type: MD5
NTP Key 3
 Trusted: yes
 Encryption Type: MD5
NTP Key 4
 Trusted: yes
 Encryption Type: md5
Related Commands
Notes