BMI088 IMU Driver

The Linux industrial IO (IIO) is framework used to implement sensor drivers such as ADC (analog to digital converters), temperature, light, IMU (inertial measurement unit). The BMI088 is Bosch IMU which encompasses accelerometer, gyroscope and temperature. This I2C based driver implements accelerometer and gyroscope part of the IMU.

Kernel Configuration

The driver can be enabled as loadable module by setting CONFIG_BMI088_IIO=m. In addition, the kernel config for the hardware timestamping CONFIG_TEGRA_HTS_GTE must be set to y.

Note

Remember the following information:

  • CONFIG_BMI088_IIO will only appear after CONFIG_TEGRA_HTS_GTE is set.

  • The driver config depends on CONFIG_I2C, CONFIG_SYSFS, CONFIG_IIO.

  • Do not select the CONFIG_NVS_BMI08X_IIO config.

BMI088 Driver

Since both the devices have separate I2C addresses and register spaces, the BMI088 driver registers each accelerometer and gyroscope to IIO framework as separate devices. This gives control to, for example, enable or disable each device without disturbing another device. Like all IIO-based devices, both the devices will appear at /sys/bus/iio/devices/ for the userspace. The user can determine the device node by reading /sys/bus/iio/devices/iio:deviceX/name, this will yield accelerometer and gyroscope. The driver uses data ready interrupts from both the devices as a indication of the new data sets, upon receiving such interrupt driver reads data registers to retrieve the data. The data-ready interrupts must be connected to Jetson Always On (AON) GPIOs, which have hardware timestamp capability to record the accurate time of the interrupt occurrences. This timestamp the data will be passed to userspace through IIO framework. The driver supports only data-ready interrupt mode.

Device Tree

This section provides information about the device tree.

Required Properties

Here is the list of the required properties:

  • compatible: Must be set to bmi,bmi088.

  • accel_i2c_addr: Must be set to the appropriate value based on the datasheet and platform configuration because the i2c address might be different based on how some pins are tied up.

  • reg: Must be set to the gyroscope I2C address based on the datasheet and platform configuration because the i2c address might be different based on how some pins are tied up.

  • gyro_irq_gpio: The value is based on which GPIO line is connected to the gyroscope’s data-ready interrupt.

  • accel_irq_gpio: The value is based on the GPIO line that is connected to the accelerometer’s data-ready interrupt.

  • status: To enable the DT node, set to okay.

Optional Properties

Here is the list of the optional properties:

  • accel_matrix
    • An array in the accelerometer mount matrix.

  • gyro_matrix
    • An array of gyroscope mount matrix.

  • accel_reg_0x53
    • The accelerometer INT1 config register, and the driver default value is 0xA.

    • The value 0xA makes INT1 line as the output and active high.

  • accel_reg_0x54
    • The accelerometer INT2 config register, and driver default value is 0x0.

    • By default driver uses INT1. Refer to the device datasheet for more information.

    • Select INT1 or INT2 as the data-ready interrupt.

  • gyro_reg_0x16
    • The gyroscope INT3/INT4 config register, and the driver default value is 0x1.

    • The default value makes INT3 as active high output line.

    • Refer to the device datasheet for more information.

  • gyro_reg_0x18
    • The gyroscope INT3/INT4 mapping register, and the driver default value is 0x1.

    • The default value maps INT3 the the data-ready interrupt.

    • Refer to the device datasheet for more information.

    • Select INT3 or INT4 as the data-ready interrupt.

Here is an example:

bmi088@69 {
  compatible = "bmi,bmi088";
  accel_i2c_addr = <0x19>;
  status = "okay";
  reg = <0x69>;
  accel_irq_gpio = <&tegra_aon_gpio TEGRA_AON_GPIO(BB, 0) GPIO_ACTIVE_HIGH>;
  gyro_irq_gpio = <&tegra_aon_gpio TEGRA_AON_GPIO(BB, 1) GPIO_ACTIVE_HIGH>;
  accel_matrix = [01 00 00 00 01 00 00 00 01];
  gyro_matrix = [01 00 00 00 01 00 00 00 01];
  accel_reg_0x53 = <0x0A>;
  gyro_reg_0x16 = <0x01>;
  gyro_reg_0x18 = <0x01>;
};

Accelerometer IIO Attributes

The accelerometer IIO device files mentioned in the following table is available in the /sys/bus/iio/devices/iio:deviceX/ directory, where the X value is enumerated during IIO registration.

Note

The following table assumes that user is in the /sys/bus/iio/devices/iio:deviceX/ directory.

IIO sysfs Interface

Default value

Possible value

Usage

Buffer Management

buffer/enable

0

0,1

Writing 1 enables buffer and data acquisition.
  • Before you enable the buffer, at least one axis needs to be enabled.

buffer/length

64

N/A

Internally, the kernel uses kmalloc to allocate the required lengths.
  • The max value depends on the state of the system memory.

buffer/watermark

1

1, buffer length

The application using poll and friends will wait until this number of samples is collected.

Debug

dev_err

Here are the values:
  • I2C Bus Errors:0

  • GTE Timestamp Errors:0

  • Sample dropped:0

N/A

Read-only, displays the current errors.

It records i2c bus and hardware timestamp errors. The timestamp errors are recorded when the driver fails to retrieve the hardware timestamp for the specified datasets. The hardware timestamp, also known as GTE, has been divided as follows:

  • GTE Timestamp Errors: a real timestamp failure, which means that the driver was not able to retrieve the hardware timestamp.

  • Sample dropped: the were samples dropped.

    This can happen when the data rate is higher than what i2c bus can handle.

dev_state

N/A

N/A

Read-only and displays the device state, for example, suspend/shutdown.

dump_regs

N/A

N/A

Read-only and dumps the current register values.

Common attributes

in_accel_sampling_frequency

12.5

12.5, 25, 50, 100, 200, 400, 800, 1600

This is the output data rate (ODR) in Hz, and the user can write any values from the list.

The I2C bus clock speed dictates what the user can program.

in_accel_sampling_frequency_available

12.5, 25, 50, 100, 200, 400, 800, 1600

NA

Read-only and displays the available ODRs.

in_accel_scale

0.000897

0.000897, 0.00179, 0.003591, 0.007182

This interface represents the resolution, and its value will be used to calculate the actual value from the raw data.

Stop the user space application before you change the scale value.

in_accel_scale_available

0.000897, 0.00179, 0.003591, 0.007182

N/A

Read-only and displays available scales.

in_accel_x_raw

N/A

N/A

Fetches the raw X-axis value. To read, the respective scan element and device buffer must be enabled.

in_accel_y_raw

N/A

N/A

Fetches raw Y-axis value. To read, the respective scan element and device buffer must be enabled.

in_accel_z_raw

N/A

N/A

Fetches raw Z-axis value. To read, the respective scan element and device buffer must be enabled.

mount_matrix

1,0,0,0,1,0,0,0,1

N/A

Read-only, displays current mount matrix, by default its identity matrix.

Refer to https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/iio/mount-matrix.txt for more information.

name

“accelerometer”

NA

A read-only value.

part

“bmi08x accelerometer”

N/A

A read-only value that displays the Bosch IMU model.

trigger/current_trigger

accelerometer-devX

N/A

The trigger comes from the device, and no other value is acceptable.

Here X is number that is the same as the enumerated IIO device.

Channel Attributes

scan_elements/in_accel_x_en

0

0,1

Writing 1 enables the X-axis/channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_accel_y_en

0

0,1

Writing 1 enables Y-axis/channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_accel_z_en

0

0,1

Writing 1 enables Z-axis/channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_timestamp_en

0

0,1

Writing 1 enables the timestamp channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_accel_x_index

0

NA

Read-only and puts the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_accel_x_index

0

NA

Read-only and puts the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_accel_y_index

1

NA

Read-only and puts the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_accel_z_index

2

N/A

Read-only and provides the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_timestamp_index

3

NA

Read-only, gives channel index into dataset.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_accel_x_type

“le:s16/16>>0”

N/A

Read-only and displays details about how X-axis data is represented in the buffer.

This value means that the data is little endian-signed 16 bits and does not require a shift operation.

scan_elements/in_accel_y_type

“le:s16/16>>0”

N/A

Read-only and displays details about how Y-axis data is represented in the buffer.

This value means data is little endian signed 16 bits and does not require shift operation.

scan_elements/in_accel_z_type

“le:s16/16>>0”

N/A

Read-only and displays details about how Z-axis data is represented in the buffer.

This value means data is little endian signed 16 bits and does not require shift operation.

scan_elements/in_timestamp_type

“le:s64/64>>0”

N/A

Read-only and displays details about how timestamp data is represented in the buffer.

This value means data is little endian signed 64 bits and does not require shift operation.

Gyroscope IIO Attributes

The gyroscope IIO device files in the following table is available in the /sys/bus/iio/devices/iio:deviceX/ directory, where the X value is enumerated during IIO registration.

Note

The following table assumes that user is in the /sys/bus/iio/devices/iio:deviceX/ directory.

IIO sysfs Interface

Default value

Possible value

Usage

Buffer Management

buffer/enable

0

0,1

Writing 1 enables buffer and data acquisition.

buffer/length

600

N/A

Internally, the kernel uses kmalloc to allocate the required lengths.
  • The max value depends on the state of the system memory that is available to the kernel at the point of request.

buffer/watermark

1

1, buffer length

The application using poll and friends will wait until this number of samples is collected.

Debug

dev_err

Here are the values:
  • I2C Bus Errors: 0

  • GTE Timestamp Errors: 0

  • Sample dropped: 0

N/A

Read-only, displays the current errors.

It records i2c bus and hardware timestamp errors. The timestamp errors are recorded when the driver fails to retrieve the hardware timestamp for the specified datasets. The hardware timestamp, also known as GTE, has been divided as follows:

  • GTE Timestamp Errors: a real timestamp failure, which means that the driver was not able to retrieve the hardware timestamp.

  • Sample dropped: the samples were dropped. This can happen when the data rate is higher than what i2c bus can handle.

dev_state

N/A

N/A

Read-only and displays the device state, for example, suspend/shutdown.

dump_regs

N/A

N/A

Read-only and dumps the current register values.

Common attributes

in_anglvel_sampling_frequency

100

100, 200, 400, 1000, 2000

This is the output data rate (ODR) in Hz, and the user can write any values from the list.

The I2C bus clock speed dictates what the user can program.

in_anglvel_sampling_frequency_available

100, 200, 400, 1000, 2000

NA

Read-only and displays the available ODRs.

in_anglvel_scale

0.001065

0.001065, 0.000532, 0.000266, 0.000133, 0.000066

This interface represents the resolution, and its value will be used to calculate the actual value from the raw data.

Stop the user space application before you change the scale value.

in_anglvel_scale_available

0.000532, 0.000266, 0.000133, 0.000066

N/A

Read-only and displays available scales.

in_anglvel_x_raw

N/A

N/A

Fetches the raw X-axis value. To read, the respective scan element and device buffer must be enabled.

in_anglvel_y_raw

N/A

N/A

Fetches raw Y-axis value. To read, the respective scan element and device buffer must be enabled.

in_anglvel_z_raw

N/A

N/A

Fetches raw Z-axis value. To read, the respective scan element and device buffer must be enabled.

mount_matrix

1,0,0,0,1,0,0,0,1

N/A

Read-only, displays current mount matrix, by default its identity matrix.

Refer to https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/iio/mount-matrix.txt for more information.

name

“gyroscope”

NA

A read-only value.

part

“bmi08x gyroscope”

N/A

A read-only value that displays the Bosch IMU model.

trigger/current_trigger

gyroscope-devX

N/A

The trigger comes from the device, and no other value is acceptable.

Here X is number that is the same as the enumerated IIO device.

Channel Attributes

scan_elements/in_anglvel_x_en

0

0,1

Writing 1 enables the X-axis/channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_anglvel_y_en

0

0,1

Writing 1 enables Y-axis/channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_anglvel_z_en

0

0,1

Writing 1 enables Z-axis/channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_timestamp_en

0

0,1

Writing 1 enables the timestamp channel, and this setting needs to be made before you enable the buffer.

scan_elements/in_anglvel_x_index

0

NA

Read-only and puts the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_anglvel_y_index

0

NA

Read-only and puts the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_anglvel_z_index

1

NA

Read-only and puts the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_timestamp_index

2

N/A

Read-only and provides the channel index to the data set.

The data set is 6 + 8 bytes, where there are two bytes for each axis, and eight bytes for the timestamp.

scan_elements/in_anglvel_x_type

“le:s16/16>>0”

N/A

Read-only and displays details about how X-axis data is represented in the buffer.

This value means that the data is little endian-signed 16 bits and does not require a shift operation.

scan_elements/in_anglvel_y_type

“le:s16/16>>0”

N/A

Read-only and displays details about how Y-axis data is represented in the buffer.

This value means data is little endian signed 16 bits and does not require shift operation.

scan_elements/in_anglvel_z_type

“le:s16/16>>0”

N/A

Read-only and displays details about how Z-axis data is represented in the buffer.

This value means data is little endian signed 16 bits and does not require shift operation.

scan_elements/in_timestamp_type

“le:s64/64>>0”

N/A

Read-only and displays details about how timestamp data is represented in the buffer.

This value means data is little endian signed 64 bits and does not require shift operation.

Testing BMI088 Driver

In the <kernel source>/tools/iio/ directory, there is a sample IIO utility where kernel source is the kernel source repository. The iio_generic_buffer.c sample application is used to demonstrate the driver. During the execution, application enables the scan elements and buffer for the specified device as described in the following procedure. After after the testing is complete, the application automatically disables the scan elements and buffer.

Hardware Timestampping Engine (GTE)

The IIO framework uses s64, for example signed 64-bits, to represent the timestamp information that gets reflected in the app iio_generic_buffer userspace app in this section. However, the GTE uses u64, for example, unsigned 64bits.

Note

To ensure that GTE uses signed bits, run the following code sample to update the iio_generic_buffer.c file before you complete the procedure in Complile and Execute procedure:

diff --git a/iio_generic_buffer.c b/iio_generic_buffer.c
index f90ea14..1cbde1e 100644
--- a/iio_generic_buffer.c
+++ b/iio_generic_buffer.c
@@ -158,7 +158,7 @@ void print8byte(uint64_t input, struct iio_channel_info *info)
printf("%05f ",
((float)val + info->offset) * info->scale);
} else {
- printf("%05f ", ((float)input + info->offset) * info->scale);
+ printf("%" PRIu64 " ", input);
}

}

Compile and Execute

  1. Copy the iio_generic_buffer.c, iio_utils.c, iio_utils.h, and bmi088.ko files to DUT, for example, at /home/ubuntu/.

  2. To install gcc on DUT, run the following command.

    $ sudo apt install -y gcc

  3. To compile the iio_generic_buffer, run the following command.

    gcc -I /home/ubuntu/ iio_utils.c iio_generic_buffer.c -o iio_generic_buffer

    Note

    This command assumes that the user is in the /home/ubuntu directory and has copied the files to the same location.

    You can complete this step from the host machine by doing a cross-compile.

    1. Set the appropriate toolchain and cross-compile variables.

      The following commands assume that the user is in the <kernel source>/tools/iio/ directory in the host machine.

      1. Export CROSS_COMPILE=<>, for example, export CROSS_COMPILE=aarch64-linux-gnu-.

      2. Export PATH=$PATH:<path to cross-compile toolchain>.

      3. Export ARCH=arm64.

    2. The make iio_generic_buffer will generate the ``iio_generic_buffer binary in the same directory.

    3. Copy the binary file to DUT.

  4. Insert bmi088.ko as the root for insmod bmi088.ko.

  5. To test accelerometer, complete the following steps:

    Note

    The following commands are executed as a root.

    1. Execute ./iio_generic_buffer -a -c 10 --device-name accelerometer -g -l 2048.

      • If you execute ./iio_generic_buffer without any options, a help message will display.

      • The command in this step will fetch 10 samples in event mode.

  6. To test gyroscope, complete the following steps:

    Note

    The following commands are executed as a root.

    • If you execute ./iio_generic_buffer without any options, a help message will display.

    • The command in this step will fetch 10 samples in event mode.

    Note

    For kernel 5.10.x and later, if the timestamp channel is specified, the IIO framework enables it by default. As a result, when you run the command above, the following error will occur:

    root@jetson:~# ./iio_generic_buffer -a -c 10 --device-name accelerometer -g -l 64
    iio device number being used is 0
    trigger-less mode selected
    Auto-channels selected but some channels are already activated in sysfs
    Proceeding without activating any channels
    Failed to enable buffer: Invalid argument
    

To disable the timestamp channel, before you run iio_generic_buffer in the Jetson device, run echo 0 > /sys/bus/iio/<iio device>/scan_elements/in_timestamp_en as a root user.

Accelerometer Sample Output

root@tegra-ubuntu:~# ./iio_generic_buffer -a -c 10 --device-name accelerometer -g
iio device number being used is 2
trigger-less mode selected
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_accel_y_en , enabled:0
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_accel_x_en , enabled:0
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_timestamp_en , enabled:0
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_accel_z_en , enabled:0
No channels are enabled, enabling all channels
Enabling: in_accel_y_en
Enabling: in_accel_x_en
Enabling: in_timestamp_en
Enabling: in_accel_z_en
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_accel_y_en , enabled:1
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_accel_x_en , enabled:1
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_timestamp_en , enabled:1
scan element filename:/sys/bus/iio/devices/iio:device2/scan_elements/in_accel_z_en , enabled:1
buffer directory: /sys/bus/iio/devices/iio:device2/buffer
X Axis   Y Axis    Z Axis   Timestamp [This row is not present in the output]
-9.484633 -0.103250 1.109713 4515182411776
-9.560051 -0.098761 1.115998 4515261579264
-9.547482 -0.096965 1.116896 4515340746752
-9.543890 -0.092476 1.117793 4515419914240
-9.547482 -0.096067 1.112406 4515499606016
-9.542993 -0.096965 1.112406 4515578773504
-9.550175 -0.107739 1.112406 4515657940992
-9.548379 -0.105046 1.115100 4515737108480
-9.540298 -0.101454 1.109713 4515816275968
-9.545686 -0.095170 1.116896 4515895443456
Disabling: in_accel_y_en
Disabling: in_accel_x_en
Disabling: in_timestamp_en
Disabling: in_accel_z_en

Gyroscope Sample Output

root@tegra-ubuntu:~# ./iio_generic_buffer -a -c 10 --device-name gyroscope -g
iio device number being used is 3
trigger-less mode selected
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_anglvel_z_en , enabled:0
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_timestamp_en , enabled:0
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_anglvel_y_en , enabled:0
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_anglvel_x_en , enabled:0
No channels are enabled, enabling all channels
Enabling: in_anglvel_z_en
Enabling: in_timestamp_en
Enabling: in_anglvel_y_en
Enabling: in_anglvel_x_en
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_anglvel_z_en , enabled:1
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_timestamp_en , enabled:1
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_anglvel_y_en , enabled:1
scan element filename:/sys/bus/iio/devices/iio:device3/scan_elements/in_anglvel_x_en , enabled:1
buffer directory: /sys/bus/iio/devices/iio:device3/buffer
X Axis   Y Axis    Z Axis   Timestamp [This row is not present in the output]
0.000000 0.000000 -0.001064 4629188837376
0.000000 0.000000 -0.002128 4629198798848
0.001064 0.000000 -0.002128 4629208760320
0.002128 0.000000 -0.002128 4629218721792
0.002128 0.000000 -0.001064 4629228683264
0.002128 0.000000 -0.001064 4629238644736
0.002128 0.000000 -0.001064 4629248606208
0.001064 0.000000 -0.001064 4629258567680
0.001064 0.000000 -0.001064 4629268529152
0.002128 -0.001064 -0.001064 4629278490624
Disabling: in_anglvel_z_en
Disabling: in_timestamp_en
Disabling: in_anglvel_y_en
Disabling: in_anglvel_x_en