|
Ref. # |
Issue |
|
N/A |
Description: Running UFM software with external UFM-SM is no longer supported |
|
Workaround: N/A |
|
|
Keywords: External UFM-SM |
|
|
N/A |
Description: If using SM mkey per port, several UFM operations might fail (get cable info, get system dump, switch FW upgrade). |
|
Workaround: N/A |
|
|
Keywords: SM, mkey per port |
|
|
N/A |
Description: If using SM mkey per port, several UFM operations might fail (get cable info, get system dump, switch FW upgrade). |
|
Workaround: N/A |
|
|
Keywords: SM, mkey per port |
|
|
Discovered in release: 4.7.1 |
|
|
2796317 |
Description: SHARP jobs may hang when running in reservations mode (i.e. SHARP allocation is enabled), and reservation is created with limited PKEY |
|
Workaround: The PKEY used for creating the reservation should be "full" (the most significant bit should be on e.g. 0x805c) |
|
|
Keywords: SHARP AM, allocation, reservation, PKEY |
|
|
Discovered in release: 4.6.0 |
|
|
- |
Description: Auto-isolated high Symbol BER ports reported by UFM as unhealthy are not automatically set back as healthy when high symbol BER is elapsed. |
|
Workaround: Manually set auto-isolated ports as healthy. |
|
|
Keywords: Unhealthy ports, auto-isolated high BER ports |
|
|
Discovered in release: 4.6.0 |
|
|
2694977 |
Description: Adding a large number of devices (~1000) to a group or a logical server, on large scale setup takes ~2 minutes. |
|
Workaround: N/A |
|
|
Keywords: Add device; group; logical server; large scale |
|
|
Discovered in release: 4.6.0 |
|
|
2710613 |
Description: Periodic topology compare will not report removed nodes if the last topology change included only removed nodes. |
|
Workaround: N/A |
|
|
Keywords: Topology comparison |
|
|
Discovered in release: 4.6.0 |
|
|
2698055 |
Description: UFM, configured to work with telemetry for collecting historical data, is limited to work only with the configured HCA port. If this port is part of a bond interface and a failure occurs on the port, collection of telemetry data via this port stops. |
|
Workaround: Reconfigure telemetry with the new active port and restart it within UFM. |
|
|
Keywords: Telemetry; history; bond; failure |
|
|
Discovered in release: 4.6.0 |
|
|
2304264 |
Description: The option to collect system dump is only supported for hosts containing the CURL utility which supports the scp and sftp protocols. |
|
Workaround: To check the protocols supported by CURL, run:
If scp and sftp are not supported, install a CURL version that supports these protocols. |
|
|
Keywords: System dump, host, CURL |
|
|
Discovered in release: 4.5.0 |
|
|
2480430 |
Description: Mellanox SHARP AM does not run with smx_sock_port value less than 1024 or greater than 49151. |
|
Workaround: N/A |
|
|
Keywords: Mellanox SHARP; aggregation manager |
|
|
Discovered in release: 4.5.0 |
|
|
2288038 |
Description: When the user try to collect system dump for UFM Appliance host, the job will be completed with an error with the following summary: "Running as a none root user Please switch to root user (super user) and run again." |
|
Workaround: N/A |
|
|
Keywords: System dump, UFM Appliance host |
|
|
Discovered in release: 4.4.0 |
|
|
2384211 |
Description: MLNX-OS version 3.9.2002 does not support SHARP allocation. |
|
Walkaround: Downgrade the switch to MLNX-OS version 3.9.1906. |
|
|
Keywords: SHARP allocation, MLNX-OS |
|
|
Discovered in release: 4.4.0 |
|
|
2366031 |
Description: When upgrading a switch with MLNX-OS version 3.9.1932 and later, you must make sure to comply with the new password requirements for admin and monitor users.
|
|
Workaround: N/A |
|
|
Keywords: User password, switch OS |
|
|
Discovered in release: 4.4.0 |
|
|
2100564 |
Description: For modular dual-management switch systems, switch information is not presented correctly if the primary management module fails and the secondary takes over. |
|
Workaround: To avoid corrupted switch information, it is recommended to manually set the virtual IP address (box IP address) for the switch as the managed switch IP address (manual IP address) within UFM. |
|
|
Keywords: Modular switch, dual-management, virtual IP, box IP |
|
|
Discovered in release: 4.3.0 |
|
|
2135272 |
Description: UFM does not support hosts equipped with multiple HCAs of different types (e.g. a host with ConnectX®-3 and ConnectX-4/5/6) if multi-NIC grouping is enabled (i.e. multinic_host_enabled = true). |
|
Workaround: All managed hosts must contain HCAs of the same type (either using ConnectX-3 HCAs or use ConnectX-4/5/6 HCAs). |
|
|
Keywords: Multiple HCAs |
|
|
Discovered in release: 4.3.0 |
|
|
2063266 |
Description: Firmware upgrade for managed hosts with multiple HCAs is not supported. That is, it is not possible to perform FW upgrade for a specific host HCA. |
|
Workaround: Running software (MLNX_OFED) upgrade on that host will automatically upgrade all the HCAs on this host with the firmware bundled as part of this software package. |
|
|
Keywords: FW upgrade, multiple HCAs |
|
|
Discovered in release: 4.3.0 |
|
|
- |
Description: When upgrading from software version 4.1.x or older to 4.2.x or later, in an intermediary step, where the standby UFM appliance is upgraded and the master UFM appliance is not, some CLI commands from the master will not be operational. This happens because, in that moment, the standby appliance is in a higher SSH security level. |
|
Workaround: After upgrading the master appliance to the latest version, CLI commands resume operations normally. |
|
|
Keywords: Upgrade, high availability, SSH |
|
|
Discovered in release: 4.2.0 |
|
|
2130688 |
Description: Registering an external SM system with two different IP addresses is not supported. |
|
Workaround: Before registering an external SM system with a new IP address, it is required to unregister the old IP address for that system. |
|
|
Keywords: External SM |
|
|
Discovered in release: 4.2.0 |
|
|
1895385 |
Description: QoS parameters (mtu, sl and rate_limit) change does not take effect unless OpenSM is restarted. |
|
Workaround: N/A |
|
|
Keywords: QoS, PKey, OpenSM |
|
|
Discovered in release: 4.2.0 |
|
|
- |
Description: Management PKey configuration (e.g. MTU, SL) can be performed only using PKey management interface (via GUI or REST API). |
|
Workaround: N/A |
|
|
Keywords: PKey, Management PKey, REST API |
|
|
Discovered in release: 4.2.0 |
|
|
- |
Description: The hostname or/and IP address of UFM HA server is used in the HA configuration. |
|
Workaround: Do not change hostname or IP address of UFM HA server unless you wish to reconfigure the HA mechanism. |
|
|
Keywords: High availability |
|
|
Discovered in release: 4.2.0 |
|
|
- |
Description: UFM-SDN Appliance supports limited number of login sessions. When the limit is reached, any available client application (GUI, Multisite Portal or SDK) will not be able to connect to UFM during the login session timeout (default timeout is 10 minutes). |
|
Workaround: When using SDK, do not exceed 5 logins per minute. |
|
|
Keywords: UFM Server |
|
|
- |
Description: Configuration from lossy to lossless requires device reset. |
|
Workaround: Reboot all relevant devices after changing behavior from lossy to lossless. |
|
|
Keywords: Lossy configuration |
