NVIDIA BlueField DPU BSP v3.8.5
1.0

Virtual Switch on BlueField DPU

Warning

For general information on OVS offload using ASAP² direct, please refer to the MLNX_OFED documentation under OVS Offload Using ASAP² Direct.

Warning

ASAP2 is only supported in Embedded (DPU) mode.

NVIDIA® BlueField® supports ASAP2 technology. It utilizes the representors mentioned in the previous section. BlueField SW package includes OVS installation which already supports ASAP2. The virtual switch running on the Arm cores allows us to pass all the traffic to and from the host functions through the Arm cores while performing all the operations supported by OVS. ASAP2 allows us to offload the datapath by programming the NIC embedded switch and avoiding the need to pass every packet through the Arm cores. The control plane remains the same as working with standard OVS.

OVS bridges are created by default upon first boot of the DPU after BFB installation.

If manual configuration of the default settings for the OVS bridge is desired, run:

Copy
Copied!
            

systemctl start openvswitch-switch.service ovs-vsctl add-port ovsbr1 p0 ovs-vsctl add-port ovsbr1 pf0hpf ovs-vsctl add-port ovsbr2 p1 ovs-vsctl add-port ovsbr2 pf1hpf

To verify successful bridging:

Copy
Copied!
            

$ ovs-vsctl show 9f635bd1-a9fd-4f30-9bdc-b3fa21f8940a Bridge ovsbr2 Port ovsbr2 Interface ovsbr2 type: internal Port p1 Interface p1 Port pf1sf0 Interface en3f1pf1sf0       Port pf1hpf Interface pf1hpf Bridge ovsbr1 Port pf0hpf Interface pf0hpf Port p0 Interface p0 Port ovsbr1 Interface ovsbr1 type: internal Port pf0sf0 Interface en3f0pf0sf0 ovs_version: "2.14.1"

The host is now connected to the network.

When the DPU is connected to another DPU on another machine, manually assign IP addresses with the same subnet to both ends of the connection.

  1. Assuming the link is connected to p3p1 on the other host, run:

    Copy
    Copied!
                

    $ ifconfig p3p1 192.168.200.1/24 up

  2. On the host which the DPU is connected to, run:

    Copy
    Copied!
                

    $ ifconfig p4p2 192.168.200.2/24 up

  3. Have one ping the other. This is an example of the DPU pinging the host:

    Copy
    Copied!
                

    $ ping 192.168.200.1

There are two SFs configured on the BlueFIeld-2 device, enp3s0f0s0 and enp3s0f1s0, and their representors are part of the built-in bridge. These interfaces will get IP addresses from the DHCP server if it is present. Otherwise it is possible to configure IP address from the host. It is possible to access BlueField via the SF netdev interfaces.

For example:

  1. Verify the default OVS configuration. Run:

    Copy
    Copied!
                

    # ovs-vsctl show 5668f9a6-6b93-49cf-a72a-14fd64b4c82b Bridge ovsbr1 Port pf0hpf Interface pf0hpf Port ovsbr1 Interface ovsbr1 type: internal Port p0 Interface p0 Port en3f0pf0sf0            Interface en3f0pf0sf0 Bridge ovsbr2 Port en3f1pf1sf0 Interface en3f1pf1sf0 Port ovsbr2 Interface ovsbr2 type: internal Port pf1hpf Interface pf1hpf Port p1 Interface p1 ovs_version: "2.14.1"

  2. Verify whether the SF netdev received an IP address from the DHCP server. If not, assign a static IP. Run:

    Copy
    Copied!
                

    # ifconfig enp3s0f0s0 enp3s0f0s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.200.125 netmask 255.255.255.0 broadcast 192.168.200.255 inet6 fe80::8e:bcff:fe36:19bc prefixlen 64 scopeid 0x20<link> ether 02:8e:bc:36:19:bc txqueuelen 1000 (Ethernet) RX packets 3730 bytes 1217558 (1.1 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 22 bytes 2220 (2.1 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

  3. Verify the connection of the configured IP address. Run:

    Copy
    Copied!
                

    # ping 192.168.200.25 -c 5 PING 192.168.200.25 (192.168.200.25) 56(84) bytes of data. 64 bytes from 192.168.200.25: icmp_seq=1 ttl=64 time=0.228 ms 64 bytes from 192.168.200.25: icmp_seq=2 ttl=64 time=0.175 ms 64 bytes from 192.168.200.25: icmp_seq=3 ttl=64 time=0.232 ms 64 bytes from 192.168.200.25: icmp_seq=4 ttl=64 time=0.174 ms 64 bytes from 192.168.200.25: icmp_seq=5 ttl=64 time=0.168 ms   --- 192.168.200.25 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 91ms rtt min/avg/max/mdev = 0.168/0.195/0.232/0.031 ms

Set IP address on the Windows side for the RShim or Physical network adapter, please run the following command in Command Prompt:

Copy
Copied!
            

PS C:\Users\Administrator> New-NetIPAddress -InterfaceAlias "Ethernet 16" -IPAddress "192.168.100.1" -PrefixLength 22

To get the interface name, please run the following command in Command Prompt:

Copy
Copied!
            

PS C:\Users\Administrator> Get-NetAdapter

Output should give us the interface name that matches the description (e.g. NVIDIA BlueField Management Network Adapter).

Copy
Copied!
            

Ethernet 2 NVIDIA ConnectX-4 Lx Ethernet Adapter 6 Not Present 24-8A-07-0D-E8-1D Ethernet 6 NVIDIA ConnectX-4 Lx Ethernet Ad...#2 23 Not Present 24-8A-07-0D-E8-1C Ethernet 16 NVIDIA BlueField Management Netw...#2 15 Up CA-FE-01-CA-FE-02

Once IP address is set, Have one ping the other.

Copy
Copied!
            

C:\Windows\system32>ping 192.168.100.2     Pinging 192.168.100.2 with 32 bytes of data: Reply from 192.168.100.2: bytes=32 time=148ms TTL=64 Reply from 192.168.100.2: bytes=32 time=152ms TTL=64 Reply from 192.168.100.2: bytes=32 time=158ms TTL=64 Reply from 192.168.100.2: bytes=32 time=158ms TTL=64

Warning

Please make sure to have SR-IOV enabled prior to following this procedure. Please refer to MLNX_OFED documentation under Features Overview and Configuration > Virtualization > Single Root IO Virtualization (SR-IOV) for instructions on how to do that.

OVS HW offloading is set by default by the /sbin/mlnx_bf_configure script upon first boot after installation.

Enable TC offload on the relevant interfaces. Run:

Copy
Copied!
            

$ ethtool -K <PF> hw-tc-offload on

To enable the HW offload run the following commands (restarting OVS is required after enabling the HW offload):

Copy
Copied!
            

$ ovs-vsctl set Open_vSwitch . Other_config:hw-offload=true $ systemctl restart openvswitch

To show OVS configuration:

Copy
Copied!
            

$ ovs-dpctl show system@ovs-system: lookups: hit:0 missed:0 lost:0 flows: 0 masks: hit:0 total:0 hit/pkt:0.00 port 0: ovs-system (internal) port 1: armbr1 (internal) port 2: p0 port 3: pf0hpf port 4: pf0vf0 port 5: pf0vf1 port 6: pf0vf2

At this point OVS would automatically try to offload all the rules.

To see all the rules that are added to the OVS datapath:

Copy
Copied!
            

$ ovs-appctl dpctl/dump-flows

To see the rules that are offloaded to the HW:

Copy
Copied!
            

$ ovs-appctl dpctl/dump-flows type=offloaded

  1. Remove previously configured ovs-bridges. Run:

    Copy
    Copied!
                

    ovs-vsctl del-br <bridge-name>

    Issue the command obs-vsctl show to see already configured OVS bridges.

  2. Enable the Open vSwitch service. Run:

    Copy
    Copied!
                

    systemctl start openvswitch

  3. Enable hardware offload (disabled by default). Run:

    Copy
    Copied!
                

    ovs-vsctl --no-wait set Open_vSwitch . other_config:dpdk-init=true ovs-vsctl --no-wait set Open_vSwitch . other_config:hw-offload=true

  4. Configure the DPDK whitelist. Run:

    Copy
    Copied!
                

    ovs-vsctl set Open_vSwitch . other_config:dpdk-extra="-w 0000:03:00.0,representor=[0,65535],dv_flow_en=1,dv_xmeta_en=1,sys_mem_en=1"

  5. Create OVS-DPDK bridge. Run:

    Copy
    Copied!
                

    ovs-vsctl add-br br0-ovs -- set Bridge br0-ovs datapath_type=netdev -- br-set-external-id br0-ovs bridge-id br0-ovs -- set bridge br0-ovs fail-mode=standalone

  6. Add PF to OVS. Run:

    Copy
    Copied!
                

    ovs-vsctl add-port br0-ovs p0 -- set Interface p0 type=dpdk options:dpdk-devargs=0000:03:00.0

  7. Add representor to OVS. Run:

    Copy
    Copied!
                

    ovs-vsctl add-port br0-ovs pf0vf0 -- set Interface pf0vf0 type=dpdk options:dpdk-devargs=0000:03:00.0,representor=[0] ovs-vsctl add-port br0-ovs pf0hpf -- set Interface pf0hpf type=dpdk options:dpdk-devargs=0000:03:00.0,representor=[65535]

  8. Restart the Open vSwitch service. This step is required for HW offload changes to take effect.

    • For CentOS, run:

      Copy
      Copied!
                  

      systemctl restart openvswitch

    • For Debian/Ubuntu, run:

      Copy
      Copied!
                  

      systemctl restart openvswitch-switch

For a reference setup configuration for BlueField-2 devices, refer to the article "Configuring OVS-DPDK Offload with BlueField-2".

  1. Configure hugepages. Run:

    Copy
    Copied!
                

    echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages

  2. Run testpmd.

    • For Ubuntu/Debian:

      Copy
      Copied!
                  

      env LD_LIBRARY_PATH=/opt/mellanox/dpdk/lib/aarch64-linux-gnu /opt/mellanox/dpdk/bin/dpdk-testpmd -w 03:00.0,representor=[0,65535] --socket-mem=1024 -- --total-num-mbufs=131000 -i -a

    • For CentOS:

      Copy
      Copied!
                  

      env LD_LIBRARY_PATH=/opt/mellanox/dpdk/lib64/ /opt/mellanox/dpdk/bin/dpdk-testpmd -w 03:00.0,representor=[0,65535] --socket-mem=1024 -- --total-num-mbufs=131000 -i -a

For a detailed procedure with port display, refer to the article "Configuring DPDK and Running testpmd on BlueField-2".

The aging timeout of OVS is given in milliseconds and can be configured by running the following command:

Copy
Copied!
            

$ ovs-vsctl set Open_vSwitch . other_config:max-idle=30000

This feature enables tracking connections and storing information about the state of these connections. When used with OVS, the DPU can offload connection tracking, so that traffic of established connections bypasses the kernel and goes directly to hardware.

Both source NAT (SNAT) and destination NAT (DNAT) are supported with connection tracking offload.

Configuring Connection Tracking Offload

This section provides an example of configuring OVS to offload all IP connections of host PF0.

  1. Enable OVS HW offloading.

  2. Create OVS connection tracking bridge. Run:

    Copy
    Copied!
                

    $ ovs-vsctl add-br ctBr

  3. Add p0 and pf0hpf to the bridge. Run:

    Copy
    Copied!
                

    $ ovs-vsctl add-port ctBr p0 $ ovs-vsctl add-port ctBr pf0hpf

  4. Configure ARP packets to behave normally. Packets which do not comply are routed to table1. Run:

    Copy
    Copied!
                

    $ ovs-ofctl add-flow ctBr "table=0,arp,action=normal" $ ovs-ofctl add-flow ctBr "table=0,ip,ct_state=-trk,action=ct(table=1)"

  5. Configure RoCEv2 packets to behave normally. RoCEv2 packets follow UDP port 4791 and a different source port in each direction of the connection. RoCE traffic is not supported by CT. In order to run RoCE from the host add the following line before ovs-ofctl add-flow ctBr "table=0,ip,ct_state=-trk,action=ct(table=1)":

    Copy
    Copied!
                

    $ ovs-ofctl add-flow ctBr table=0,udp,tp_dst=4791,action=normal

    This rule allows RoCEv2 UDP packets to skip connection tracking rules.

  6. Configure the new established flows to be admitted to the connection tracking bridge and to then behave normally. Run:

    Copy
    Copied!
                

    $ ovs-ofctl add-flow ctBr "table=1,priority=1,ip,ct_state=+trk+new,action=ct(commit),normal"

  7. Set already established flows to behave normally. Run:

    Copy
    Copied!
                

    $ ovs-ofctl add-flow ctBr "table=1,priority=1,ip,ct_state=+trk+est,action=normal"

Connection Tracking With NAT

This section provides an example of configuring OVS to offload all IP connections of host PF0, and performing source network address translation (SNAT). The server host sends traffic via source IP from 2.2.2.1 to 1.1.1.2 on another host. Arm performs SNAT and changes the source IP to 1.1.1.16. Note that static ARP or route table must be configured to find that route.

  1. Configure untracked IP packets to do nat. Run:

    Copy
    Copied!
                

    ovs-ofctl add-flow ctBr "table=0,ip,ct_state=-trk,action=ct(table=1,nat)"

  2. Configure new established flows to do SNAT, and change source IP to 1.1.1.16. Run:

    Copy
    Copied!
                

    ovs-ofctl add-flow ctBr "table=1,in_port=pf0hpf,ip,ct_state=+trk+new,action=ct(commit,nat(src=1.1.1.16)), p0"

  3. Configure already established flows act normal. Run:

    Copy
    Copied!
                

    ovs-ofctl add-flow ctBr "table=1,ip,ct_state=+trk+est,action=normal"

    Conntrack shows the connection with SNAT applied:

    Copy
    Copied!
                

    $ cat /proc/net/nf_conntrack ipv4 2 tcp 6 src=2.2.2.1 dst=1.1.1.2 sport=34541 dport=5001 src=1.1.1.2 dst=1.1.1.16 sport=5001 dport=34541 [OFFLOAD] mark=0 zone=1 use=3

Querying Connection Tracking Offload Status

Start traffic on PF0 from the server host (e.g. iperf) with an external network. Note that only established connections can be offloaded. TCP should have already finished the handshake, UDP should have gotten the reply.

Warning

ICMP is not currently supported.

To check if specific connections are offloaded from Arm, run:

Copy
Copied!
            

$ cat /proc/net/nf_conntrack

The following is example output of offloaded TCP connection:

Copy
Copied!
            

ipv4 2 tcp 6 src=1.1.1.2 dst=1.1.1.3 sport=51888 dport=5001 src=1.1.1.3 dst=1.1.1.2 sport=5001 dport=51888 [HW_OFFLOAD] mark=0 zone=0 use=3


Performance Tune Based on Traffic Pattern

Offloaded flows (including connection tracking) are added to virtual switch FDB flow tables. FDB tables have a set of flow groups. Each flow group saves the same traffic pattern flows. For example, for connection tracking offloaded flow, TCP and UDP are different traffic patterns which end up in two different flow groups.

A flow group has a limited size to save flow entries. By default, the driver has 4 big FDB flow groups. Each of these big flow groups can save at most 4000000/(4+1)=800k different 5-tuple flow entries. For scenarios with more than 4 traffic patterns, the driver provides a module parameter (num_of_groups) to allow customization and performance tune.

Warning

The size of each big flow groups can be calculated according to formula: size = 4000000/(num_of_groups+1)

To change the number of big FDB flow groups, run:

Copy
Copied!
            

$ echo <num_of_groups> > /sys/module/mlx5_core/parameters/num_of_groups

The change takes effect immediately if there is no flow inside the FDB table (no traffic running and all offloaded flows are aged out), and it can be dynamically changed without reloading the driver.

If there are residual offloaded flows when changing this parameter, then the new configuration only takes effect after all flows age out.

Connection Tracking Aging

Aside from the aging of OVS, connection tracking offload has its own aging mechanism with a default aging time of 30 seconds.

Maximum Tracked Connections

Warning

The maximum number for tracked offloaded connections is limited to 1M by default.

The OS has a default setting of maximum tracked connections which may be configured by running:

Copy
Copied!
            

$ /sbin/sysctl -w net.netfilter.nf_conntrack_max=1000000

This changes the maximum tracked connections (both offloaded and non-offloaded) setting to 1 million.

The following option specifies the limit on the number of offloaded connections. For example:

Copy
Copied!
            

# devlink dev param set pci/${pci_dev} name ct_max_offloaded_conns value $max cmode runtime

This value is set to 1 million by default from BlueFiled. Users may choose a different number by using the devlink command.

Warning

Make sure net.netfilter.nf_conntrack_tcp_be_liberal=1 when using connection tracking.


OVS enables VF traffic to be tagged by the virtual switch.

For the BlueField DPU, the OVS can add VLAN tag (VLAN push) to all the packets sent by a network interface running on the host (either PF or VF) and strip the VLAN tag (VLAN pop) from the traffic going from the wire to that interface. Here we operate in Virtual Switch Tagging (VST) mode. This means that the host/VM interface is unaware of the VLAN tagging. Those rules can also be offloaded to the HW embedded switch.

To configure OVS to push/pop VLAN you need to add the tag=$TAG section for the OVS command line that adds the representor ports. So if you want to tag all the traffic of VF0 with VLAN ID 52, you should use the following command when adding its representor to the bridge:

Copy
Copied!
            

$ ovs-vsctl add-port armbr1 pf0vf0 tag=52

Warning

If the virtual port is already connected to the bridge prior to configuring VLAN, you would need to remove it first:

Copy
Copied!
            

$ ovs-vsctl del-port pf0vf0

In this scenario all the traffic being sent by VF 0 will have the same VLAN tag. We could set a VLAN tag by flow when using the TC interface, this is explained in section "Using TC Interface to Configure Offload Rules".

VXLAN tunnels are created on the Arm side and attached to the OVS. VXLAN decapsulation/encapsulation behavior is similar to normal VXLAN behavior, including over hw_offload=true.

To allow VXLAN encapsulation, the uplink representor (p0) should have an MTU value at least 50 bytes greater than that of the host PF/VF. Please refer to "Configuring Uplink MTU" for more information.

Configuring VXLAN Tunnel

  1. Consider p0 to be the local VXLAN tunnel interface.

  2. Build a VXLAN tunnel over OVS arm-ovs. Run:

    Copy
    Copied!
                

    ovs-vsctl add-port arm-ovs vxlan11 -- set interface vxlan11 type=vxlan options:local_ip=1.1.1.1 options:remote_ip=1.1.1.2 options:key=100 options:dst_port=4789

  3. Connect pf0hpf to the same arm-ovs.

  4. Run traffic over PF0 on x86 (the one connected to pf0hpf) to the host the DPU connected.

  5. Configure the MTU of the PF used by VXLAN to at least 50 bytes larger than VXLAN-REP MTU.

Querying OVS VXLAN hw_offload Rules

Run the following:

Copy
Copied!
            

ovs-appctl dpctl/dump-flows type=offloaded in_port(2),eth(src=ae:fd:f3:31:7e:7b,dst=a2:fb:09:85:84:48),eth_type(0x0800), packets:1, bytes:98, used:0.900s, actions:set(tunnel(tun_id=0x64,src=1.1.1.1,dst=1.1.1.2,tp_dst=4789,flags(key))),3 tunnel(tun_id=0x64,src=1.1.1.2,dst=1.1.1.1,tp_dst=4789,flags(+key)),in_port(3),eth(src=a2:fb:09:85:84:48,dst=ae:fd:f3:31:7e:7b),eth_type(0x0800), packets:75, bytes:7350, used:0.900s, actions:2

Warning

For the host PF, in order for VXLAN to work properly with the default 1500 MTU, follow these steps.

  1. Disable host PF as the port owner from Arm (see section "Restricting DPU Host"). Run:

    Copy
    Copied!
                

    $ mlxprivhost -d /dev/mst/mt41682_pciconf0 --disable_port_owner r

  2. The MTU of the end points (pf0hpf in the example above) of the VXLAN tunnel must be smaller than the MTU of the tunnel interfaces (p0) to account for the size of the VXLAN headers. For example, you can set the MTU of P0 to 2000.


GRE tunnels are created on the Arm side and attached to the OVS. GRE decapsulation/encapsulation behavior is similar to normal GRE behavior, including over hw_offload=true.

To allow GRE encapsulation, the uplink representor (p0) should have an MTU value at least 50 bytes greater than that of the host PF/VF.

Please refer to "Configuring Uplink MTU" for more information.

Configuring GRE Tunnel

  1. Consider p0 to be the local GRE tunnel interface.

  2. Build a GRE tunnel over OVS arm-ovs. Run:

    Copy
    Copied!
                

    ovs-vsctl add-port gre_br gre0 -- set interface gre0 type=gre options:local_ip=1.1.1.1 options:remote_ip=1.1.1.2 options:key=100

  3. Connect pf0hpf to the same arm-ovs.

  4. Run traffic over PF0 on x86 (the one connected to pf0hpf) to the host the DPU connected.

Querying OVS GRE hw_offload Rules

Run the following:

Copy
Copied!
            

ovs-appctl dpctl/dump-flows type=offloaded recirc_id(0),in_port(3),eth(src=50:6b:4b:2f:0b:74,dst=de:d0:a3:63:0b:30),eth_type(0x0800),ipv4(frag=no), packets:878, bytes:122802, used:0.440s, actions:set(tunnel(tun_id=0x64,src=1.1.1.1,dst=1.1.1.2,ttl=64,flags(key))),2 tunnel(tun_id=0x64,src=1.1.1.1,dst=1.1.1.2,flags(+key)),recirc_id(0),in_port(2),eth(src=de:d0:a3:63:0b:30,dst=50:6b:4b:2f:0b:74),eth_type(0x0800),ipv4(frag=no), packets:995, bytes:97510, used:0.440s, actions:3

Warning

For the host PF, in order for GRE to work properly with the default 1500 MTU, follow these steps.

  1. Disable host PF as the port owner from Arm (see section "Restricting DPU Host"). Run:

    Copy
    Copied!
                

    $ mlxprivhost -d /dev/mst/mt41682_pciconf0 --disable_port_owner r

  2. The MTU of the end points (pf0hpf in the example above) of the GRE tunnel must be smaller than the MTU of the tunnel interfaces (p0) to account for the size of the GRE headers. For example, you can set the MTU of P0 to 2000.


Geneve tunnels are created on the Arm side and attached to the OVS. Geneve decapsulation/encapsulation behavior is similar to normal Geneve behavior, including over hw_offload=true.

To allow Geneve encapsulation, the uplink representor (p0) must have an MTU value at least 50 bytes greater than that of the host PF/VF.

Please refer to "Configuring Uplink MTU" for more information.

Configuring Geneve Tunnel

  1. Consider p0 to be the local Geneve tunnel interface.

  2. Build a Geneve tunnel over OVS arm-ovs. Run:

    Copy
    Copied!
                

    ovs-vsctl add-port geneve_br gv0 -- set interface gv0 type=geneve options:local_ip=1.1.1.1 options:remote_ip=1.1.1.2 options:key=100

  3. Connect pf0hpf to the same arm-ovs.

  4. Run traffic over PF0 on x86 (the one connected to pf0hpf) to the host the DPU connected.

Options are supported for Geneve. For example, you may add option 0xea55 to tunnel metadata, run:

Copy
Copied!
            

ovs-ofctl add-tlv-map geneve_br "{class=0xffff,type=0x0,len=4}->tun_metadata0" ovs-ofctl add-flow geneve_br ip,actions="set_field:0xea55->tun_metadata0",normal

Warning

For the host PF, in order for Geneve to work properly with the default 1500 MTU, follow these steps.

  1. Disable host PF as the port owner from Arm (see section "Restricting DPU Host"). Run:

    Copy
    Copied!
                

    $ mlxprivhost -d /dev/mst/mt41682_pciconf0 --disable_port_owner r

  2. The MTU of the end points (pf0hpf in the example above) of the Geneve tunnel must be smaller than the MTU of the tunnel interfaces (p0) to account for the size of the Geneve headers. For example, you can set the MTU of P0 to 2000.


Offloading rules can also be added directly, and not just through OVS, using the tc utility. To enable TC ingress on all the representors (i.e. uplink, PF, and VF).

Copy
Copied!
            

$ tc qdisc add dev p0 ingress $ tc qdisc add dev pf0hpf ingress $ tc qdisc add dev pf0vf0 ingress

L2 Rules Example

The rule below drops all packets matching the given source and destination MAC addresses:

Copy
Copied!
            

$ tc filter add dev pf0hpf protocol ip parent ffff: \ flower \ skip_sw \ dst_mac e4:11:22:11:4a:51 \ src_mac e4:11:22:11:4a:50 \ action drop


VLAN Rules Example

The following rules push VLAN ID 100 to packets sent from VF0 to the wire (and forward it through the uplink representor) and strip the VLAN when sending the packet to the VF.

Copy
Copied!
            

$ tc filter add dev pf0vf0 protocol 802.1Q parent ffff: \ flower \ skip_sw \ dst_mac e4:11:22:11:4a:51 \ src_mac e4:11:22:11:4a:50 \ action vlan push id 100 \ action mirred egress redirect dev p0   $ tc filter add dev p0 protocol 802.1Q parent ffff: \ flower \ skip_sw \ dst_mac e4:11:22:11:4a:51 \ src_mac e4:11:22:11:4a:50 \ vlan_ethtype 0x800 \ vlan_id 100 \ vlan_prio 0 \ action vlan pop \ action mirred egress redirect dev pf0vf0


VXLAN Encap/Decap Example

Copy
Copied!
            

$ tc filter add dev pf0vf0 protocol 0x806 parent ffff: \ flower \ skip_sw \ dst_mac e4:11:22:11:4a:51 \ src_mac e4:11:22:11:4a:50 \ action tunnel_key set \ src_ip 20.1.12.1 \ dst_ip 20.1.11.1 \ id 100 \ action mirred egress redirect dev vxlan100   $ tc filter add dev vxlan100 protocol 0x806 parent ffff: \ flower \ skip_sw \ dst_mac e4:11:22:11:4a:51 \ src_mac e4:11:22:11:4a:50 \ enc_src_ip 20.1.11.1 \ enc_dst_ip 20.1.12.1 \ enc_key_id 100 \ enc_dst_port 4789 \ action tunnel_key unset \ action mirred egress redirect dev pf0vf0


For configuration procedure, please refer to the MLNX_OFED documentation under OVS Offload Using ASAP² Direct > VirtIO Acceleration through Hardware vDPA.

© Copyright 2023, NVIDIA. Last updated on Sep 9, 2023.