Commands

stats alarm clear

	stats alarm <alarm ID> clear Clears alarm state.
Syntax Description	alarm ID	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
Default	N/A
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats alarm cpu_util_indiv clear
Related Commands	show stats alarm
Notes

stats alarm enable

	stats alarm <alarm-id> enable no stats alarm <alarm-id> enable Enables the alarm. The no form of the command disables the alarm, notifications will not be received.
Syntax Description	alarm ID	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
Default	The default is different per alarm-id
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats alarm cpu_util_indiv enable
Related Commands	show stats alarm
Notes

stats alarm event-repeat

	stats alarm <alarm ID> event-repeat {single \| while-not-cleared} no stats alarm <alarm ID> event-repeat Configures repetition of events from this alarm. The no form of this command resets this parameter to its default.
Syntax Description	alarm ID	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	single	Does not repeat events: only sends one event whenever the alarm changes state.
	while-not-cleared	Repeats error events until the alarm clears.
Default	single
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats alarm cpu_util_indiv event-repeat single
Related Commands	show stats alarm
Notes

stats alarm {rising | falling}

	stats alarm <alarm ID> {rising \| falling} {clear-threshold \| error-threshold} <threshold-value> Configure alarms thresholds.
Syntax Description	alarm ID	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	falling	Configures alarm for when the statistic falls too low
	rising	Configures alarm for when the statistic rises too high
	error-threshold	Sets threshold to trigger falling or rising alarm
	clear-threshold	Sets threshold to clear falling or rising alarm
	threshold-value	The desired threshold value, different per alarm
Default	Default is different per alarm-id
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats alarm cpu_util_indiv falling clear-threshold 10
Related Commands	show stats alarm
Notes	Not all alarms support all four thresholds.

stats alarm rate-limit

	stats alarm <alarm ID> rate-limit {count <count-type> <count> \| reset \| window <window-type> <duration>} Configures alarms rate limit.
Syntax Description	alarm ID	Alarms supported by the system, for example: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	count-type	Long medium, or short count (number of alarms)
	reset	Set the count and window durations to default values for this alarm
	window-type	Long medium, or short count, in seconds
Default	Short window: 5 alarms in 1 hour Medium window: 20 alarms in 1 day Long window: 50 alarms in 7 days
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats alarm paging rate-limit window long 2000
Related Commands	show stats alarm
Notes

stats chd clear

	stats chd <CHD ID> clear Clears CHD counters.
Syntax Description	CHD ID	CHD supported by the system, for example: cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average (KB/sec) fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – filesystem system usage average: bytes intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults eth_day eth_hour eth_ip_day eth_ip_hour
Default	N/A
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats chd memory_day clear
Related Commands	show stats chd
Notes

stats chd enable

	stats chd <chd-id> enable no stats chd <chd-id> enable Enables the CHD. The no form of the command disables the CHD.
Syntax Description	chd-id	CHD supported by the system, for example: cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average: KB/sec fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – filesystem system usage average: bytes intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults eth_day eth_hour
Default	Enabled
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats chd memory_day enable
Related Commands	show stats chd
Notes

stats chd compute time

	stats chd <CHD ID> compute time {interval \| range} <number of seconds> Sets parameters for when this CHD is computed.
Syntax Description	CHD ID	Possible IDs: cpu_util – CPU utilization: percentage of time spent cpu_util_ave – CPU utilization average: percentage of time spent cpu_util_day – CPU utilization average: percentage of time spent disk_device_io_hour – storage device I/O read/write statistics for the last hour: bytes disk_io – operating system aggregate disk I/O average: KB/sec fs_mnt_day – filesystem system usage average: bytes fs_mnt_month – filesystem system usage average: bytes fs_mnt_week – filesystem system usage average: bytes intf_day – network interface statistics aggregation: bytes intf_hour – network interface statistics (same as “interface” sample) intf_util – aggregate network utilization across all interfaces memory_day – average physical memory usage: bytes memory_pct – average physical memory usage paging – paging activity: page faults paging_day – paging activity: page faults eth_day eth_hour
	interval	Specifies calculation interval (how often to do a new calculation) in number of seconds
	range	Specifies calculation range, in number of seconds
	number of seconds	Number of seconds
Default	Different per CHD
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats chd memory_day compute time interval 120
Related Commands	show stats chd
Notes

stats export

	stats export <format> <sample-id> Exports collected information to a file.Can export extended "interface-ethernet", "interface-port-channel", "interface-mlag-port-channel"& "power" samples.
Syntax Description	memory	Memory utilization
	paging	Paging I/O
	telemetry	Telemetry histogram
	cpu_util	CPU utilization
	power	Power
Default	N/A
Configuration Mode	config
History	3.7.1102 3.10.1000: Updated syntax description options
Example	switch (config) # stats export csv memory
Related Commands	show stats sample
Notes

stats sample clear

	stats sample <sample ID> clear Clears sample history.
Syntax Description	sample ID	Possible sample IDs are: congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec fan - Fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature interface-ethernet – Ethernet counters statistics: counter units interface-mlag-port-channel – MLAG counters statistics: counter units interface-port-channel – LAG counters statistics: counter units eth eth-abs eth_ip
Default	N/A
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats sample temperature clear
Related Commands	show stats sample
Notes

stats sample enable

	stats sample <sample-id> enable no states sample <sample-id> enable Enables the sample. The no form of the command disables the sample.
Syntax Description	sample-id	Possible sample IDs are: congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature interface-ethernet – Ethernet counters statistics: counter units interface-mlag-port-channel – MLAG counters statistics: counter units interface-port-channel – LAG counters statistics: counter units eth eth-abs eth_ip
Default	Enabled
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats sample temperature enable
Related Commands	show stats sample
Notes

stats sample interval

	stats sample <sample-id> interval [<interval>] no stats sample <sample-id> interval [<interval>] Sets the sampling interval between taking of sample records. The no form of the command sets interval to default value.
Syntax Description	sample-id	Sample name for which report file should be generated. congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature interface-ethernet – Ethernet counters statistics: counter units interface-mlag-port-channel – MLAG counters statistics: counter units interface-port-channel – LAG counters statistics: counter units eth eth-abs eth_ip
	interval	Measured in seconds. Range: 1 - 86400 (24 hours)
Default	Default for “interface” samples is 60 seconds
Configuration Mode	config
History	3.7.1102
Example	switch (config) # stats sample interface-ethernet interval 1
Related Commands	show stats sample
Notes

stats sample max-entries

	stats sample <sample-id> max-entries [<max-entries>] no stats sample <sample-id> max-entries [<max-entries>] Sets number of records to be kept in memory for the counter. The no form of the command resets the value to its default.
Syntax Description	sample-id	Sample name for which report file should be generated. congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature interface-ethernet – Ethernet counters statistics: counter units interface-mlag-port-channel – MLAG counters statistics: counter units interface-port-channel – LAG counters statistics: counter units eth eth-abs eth_ip
	max-entries	Number of records Range: 1-1000
Default	Default “interface” samples is 100 records
Configuration Mode	config
History	3.7.1102
Example	switch (config) # stats sample interface-ethernet max-entries 1000
Related Commands	show stats sample
Notes	Setting a new value will delete all sample history. History does not persist after reboot.

stats clear-all

	stats clear-all Clears data for all samples, CHDs, and status for all alarms.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	3.1.0000
Example	switch (config) # stats clear-all
Related Commands	show stats sample
Notes

show stats alarm

	show stats alarm [<alarm-id> [rate-limit]] Displays status of all alarms or the specified alarm.
Syntax Description	alarm-id	Available values: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
	rate-limit	Displays rate limit parameters.
Default	N/A
Configuration Mode	Any command mode
History	3.1.0000
Example	switch (config) # show stats alarm Alarm cpu_util_indiv (Average CPU utilization too high): ok Alarm disk_io (Operating System Disk I/O per second too high): (disabled) Alarm fs_mnt (Free filesystem space too low): ok Alarm intf_util (Network utilization too high): (disabled) Alarm memory_pct_used (Too much memory in use): (disabled) Alarm paging (Paging activity too high): ok Alarm temperature (Temperature is too high): ok
Related Commands	stats alarm
Notes

show stats chd

	show stats chd [<chd-id>] Displays configuration of all statistics CHDs.
Syntax Description	chd-id	Available values: cpu_util_indiv – average CPU utilization too high: percent utilization disk_io – operating System Disk I/O per second too high: kilobytes per second fs_mnt – free filesystem space too low: percent of disk space free intf_util – network utilization too high: bytes per second memory_pct_used – too much memory in use: percent of physical memory used paging – paging activity too high: page faults temperature – temperature is too high: degrees
Default	N/A
Configuration Mode	Any command mode
History	3.1.0000
Example	switch (config) # show stats chd disk_device_io_hour CHD "disk_device_io_hour" (Storage device I/O read/write statistics for the last hour: bytes): Enabled: yes Source dataset: sample "disk_device_io" Computation basis: data points Interval: 1 data point(s) Range: 1 data point(s)
Related Commands	stats chd
Notes

show stats cpu

	show stats cpu Displays some basic stats about CPU utilization: the current level the peak over the past hour the average over the past hour
Syntax Description	N/A
Default	N/A
Configuration Mode	Any command mode
History	3.1.0000
Example	switch (config) # show stats cpu CPU 0 Utilization: 6% Peak Utilization Last Hour: 16% at 2012/02/28 08:47:32 Avg. Utilization Last Hour: 8%
Related Commands
Notes

show stats sample

	show stats sample [<sample-id>] Displays sampling interval for all samples, or the specified one.
Syntax Description	sample-id	Sample name for which report file should be generated. congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature interface-ethernet – Ethernet counters statistics: counter units interface-mlag-port-channel – MLAG counters statistics: counter units interface-port-channel – LAG counters statistics: counter units eth eth-abs eth_ip
Default	N/A
Configuration Mode	Any command mode
History	3.1.0000
Example	switch (config) # show stats sample fan Sample "fan" (Fan speed): Enabled: yes Sampling interval: 1 minute 11 seconds
Related Commands
Notes

show stats sample data

	show stats sample <sample-id> data [interface {ethernet \| port-channel \| mlag-port-channel} <device/port> [counter <counter-name>] ] [group name <group-name> [counter <counter-name>] ] [max-samples {<max-samples> \| all}] Displays history of counter values (i.e., collected information for a sample).
Syntax Description	sample-id	Sample name for which report file should be generated. congested cpu_util – CPU utilization: milliseconds of time spent disk_device_io – storage device I/O statistics disk_io – operating system aggregate disk I/O: KB/sec fan – fan speed fs_mnt_bytes – filesystem usage: bytes fs_mnt_inodes – filesystem usage: inodes interface – network interface statistics intf_util – network interface utilization: bytes memory – system memory utilization: bytes paging – paging activity: page faults power – power supply usage power-consumption temperature – modules temperature interface-ethernet – Ethernet counters statistics: counter units interface-mlag-port-channel – MLAG counters statistics: counter units interface-port-channel – LAG counters statistics: counter units eth eth-abs eth_ip
	interface	Allows limiting output to a particular interface’s counters
	group	Allows limiting output to a particular group of counters
	counter	Allows limiting output to a particular counter. This option is available only if the option interface or group is chosen.
	max-samples	Allows choosing a number of counter records to display. Range: 1-1000 records. The “all” option is meant for all available records. By default, 20 counter records are displayed.
Default	N/A
Configuration Mode	Any command mode
History	3.7.1102 3.8.1000: Modified configuration mode & example 3.9.2000: Modified note and example
Example
switch (config) # show stats sample interface-ethernet data interface ethernet 1/1 max-samples 1 Sampling data for Interface ethernet counters: Eth1/1: ------------------------------------------------------------------ Name Timestamp Value ------------------------------------------------------------------ Rx_packets 2000/12/25 10:27:53 0 Rx_unicast_packets 2000/12/25 10:27:53 0 Rx_multicast_packets 2000/12/25 10:27:53 0 Rx_broadcast_packets 2000/12/25 10:27:53 0 Rx_bytes 2000/12/25 10:27:53 0 Rx_discard_packets 2000/12/25 10:27:53 0 Rx_error_packets 2000/12/25 10:27:53 0 Rx_fcs_errors 2000/12/25 10:27:53 0 Rx_undersize_packets 2000/12/25 10:27:53 0 Rx_oversize_packets 2000/12/25 10:27:53 0 Rx_pause_packets 2000/12/25 10:27:53 0 Rx_unknown_control_opcode 2000/12/25 10:27:53 0 Rx_symbol_errors 2000/12/25 10:27:53 0 Rx_packets_of_64_bytes 2000/12/25 10:27:53 0 Rx_packets_of_65-127_bytes 2000/12/25 10:27:53 0 Rx_packets_of_128-255_bytes 2000/12/25 10:27:53 0 Rx_packets_of_256-511_bytes 2000/12/25 10:27:53 0 Rx_packets_of_512-1023_bytes 2000/12/25 10:27:53 0 Rx_packets_of_1024-1518_bytes 2000/12/25 10:27:53 0 Rx_packets_Jumbo 2000/12/25 10:27:53 0 Tx_packets 2000/12/25 10:27:53 0 Tx_unicast_packets 2000/12/25 10:27:53 0 Tx_multicast_packets 2000/12/25 10:27:53 0 Tx_broadcast_packets 2000/12/25 10:27:53 0 Tx_bytes 2000/12/25 10:27:53 0 Tx_discard_packets 2000/12/25 10:27:53 0 Tx_error_packets 2000/12/25 10:27:53 0 Tx_hoq_discard_packets 2000/12/25 10:27:53 0 Tx_pause_packets 2000/12/25 10:27:53 0 Tx_pause_duration 2000/12/25 10:27:53 0
Related Commands
Notes	Filtering keyword depends on chosen <sample-id>. For convenience, “interface” samples such as “interface-ethernet”, “interface-port-channel” and “interface-mlag-port-channel” have interface related keywords for choosing a counters group. Notice that this is a history of counters. Autocompletion and output can contain information for groups (interfaces) that is not present anymore in the system, and vice versa. If counters are not sampled, they will not appear in the output. Output of collected information is implemented only for the following samples: memory paging power interface-port-channel interface-ethernet interface-mlag-port-channel

Content

Space Tools

On This Page

Commands

stats alarm clear

stats alarm enable

stats alarm event-repeat

stats alarm {rising | falling}

stats alarm rate-limit

stats chd clear

stats chd enable

stats chd compute time

stats export

stats sample clear

stats sample enable

stats sample interval

stats sample max-entries

stats clear-all

show stats alarm

show stats chd

show stats cpu

show stats sample

show stats sample data

Content

Space Tools

Statistics and Alarms

On This Page

Commands

stats alarm clear

stats alarm enable

stats alarm event-repeat

stats alarm {rising | falling}

stats alarm rate-limit

stats chd clear

stats chd enable

stats chd compute time

stats export

stats sample clear

stats sample enable

stats sample interval

stats sample max-entries

stats clear-all

show stats alarm

show stats chd

show stats cpu

show stats sample

show stats sample data