General

NVIDIA Docs Hub NVIDIA Networking Networking Software Management Software NVIDIA UFM-SDN Appliance Command Reference Guide v4.15.0 General

On This Page

ufm start
show ufm status
ufm counters
show ufm counters

ufm start

	ufm start no ufm start Starts UFM. The no form of the command stops UFM.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	1.5
Example	Copy Copied! `ufm [ mgmt-sa ] (config) # ufm start`
Related Commands	show ufm status
Notes

show ufm status

	show ufm status Displays the status of UFM. The outcome of the command varies according to the working mode.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	1.5
	1.6	Updated output
	1.7	Updated output
	4.4.0	Updated output
	4.5.0	Updated output
	4.7.0	Updated output
Example	Copy Copied! r-ufm237 [ mgmt-ha-active ] (config) # show ufm status UFM mode: Management Local - r-ufm237 (10.209.36.86) ======================================== UFM Running SM Running Telemetry Running Health Running UnhealthyPorts Running DailyReport Running SHArP N/A DRBD Running Primary DRBD State ConnectionState = Connected - DiskState = UpToDate Heartbeat Running (Master) HA Interface eth0 (connected to 10.209.36.89) Mgmt. Interface eth0 (up) ======================================== UFM mode: Management Peer - r-ufm238 (10.209.36.89) ======================================== UFM Stopped SM Stopped Telemetry Stopped Health Stopped UnhealthyPorts Stopped DailyReport N/A SHArP N/A DRBD Running Secondary DRBD State ConnectionState = Connected - DiskState = UpToDate Heartbeat Running (Slave) HA Interface eth0 (connected to 10.209.36.86) Mgmt. Interface eth0 (up) ======================================== Virtual IP - 10.209.36.199 ======================================== High Availability Status: OK ======================================== r-ufm237 [ mgmt-ha-active ] (config) #
Related Commands	ufm start
Notes	The output example above is taken from a high-availability setup If working in HA mode, you will receive information on the HA status and virtual IP The status for events forwarder is displayed only if the feature is enabled The process status can be one of the below: Running – the process is running Stopped – the process is not running N/A – the process status is not applicable (e.g. NVIDIA SHARP is disabled, status on the standby node, etc…)

ufm counters

	ufm counters [ext-ports-only \| interval <sec> <never> \| max-files <number> \| upload <filename> <upload URL>] Configures the settings of UFM counters.
Syntax Description	ext-ports-only	Configures settings for UFM ext ports only
	interval	Configures settings for UFM counters interval. The settings can be: sec – number of seconds 30 - 3600 never – disable settings for UFM counters interval
	max-files	Configures the UFM counters maximum number of files (0-72)
	upload	Uploads the UFM counters file to a remote host or a USB device. filename: UFM counters filename Upload URL: The URL path from where the counters file can be uploaded. http, https, ftp, tftp, scp, sftp and usb are supported. Example: scp://username[:password]@hostname/path/filename, usb:/path/filename
Default	N/A
Configuration Mode	config
History	1.6
Example	Copy Copied! `ufm [ mgmt-sa ] (config) # ufm counters max-files 25`
Related Commands	show ufm counters
Notes

show ufm counters

	show ufm counters Displays UFM counters settings.
Syntax Description	N/A
Default	N/A
Configuration Mode	config
History	1.6
Example	Copy Copied! `ufmapl [ mgmt-sa ] (config) # show ufm counters counters interval = never max files = 5 ext ports only = disable`
Related Commands	ufm counters
Notes

© Copyright 2023, NVIDIA. Last updated on Feb 8, 2024.