Regulatory Compliance Information#
Safety Information#
NVIDIA products are designed to operate safely when installed and used according to the product instructions and general safety practices. The guidelines included in this document explain the potential risks associated with equipment operation and provide important safety practices designed to minimize these risks. By carefully following the information contained in this document, you can protect yourself from hazards and create a safer environment.
This product is designed and tested to meet IEC 62368-1 (Standard for Safety Audio/video, information and communication technology equipment). This also covers the national implementation of IEC 62368-1 based safety standards around the world, for example UL 62368-1. These standards reduce the risk of injury from the following hazards:
Electric shock: Hazardous voltage levels contained in parts of the product
Fire: Overload, temperature, material flammability
Mechanical: Sharp edges, moving parts, instability
Energy: Circuits with high energy levels (240-volt amperes) or potential as burn hazards
Heat: Accessible parts of the product at high temperatures
Chemical: Chemical fumes and vapors
Radiation: Noise, ionizing, laser, ultrasonic waves
Retain and follow all product safety and operating instructions. Always refer to the documentation supplied with your equipment. Observe all warnings on the product and in the operating instructions.
Note
Read all the safety information below and operating instructions before using DGX Spark to avoid injury.
Warning
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK OR OTHER INJURY OR DAMAGE. ELECTRICAL EQUIPMENT CAN BE HAZARDOUS IF MISUSED. OPERATION OF THIS PRODUCT, OR SIMILAR PRODUCTS, MUST ALWAYS BE SUPERVISED BY AN ADULT. DO NOT ALLOW CHILDREN ACCESS TO THIS ELECTRICAL PRODUCT AND DO NOT PERMIT THEM TO HANDLE ANY CABLES.
To reduce the risk of bodily injury, electric shock, fire, and damage to the equipment, observe the safety labels included on the equipment.
Anti-Static Precautions#
Avoid working in areas where static electricity can build up, such as carpeted areas.
To minimize the possibility of a static charge harming the hardware, always use a properly grounded anti-static wrist strap when working with DGX Spark.
In addition, always discharge any residual static electricity that may be present by touching a non-conducting edge of the kit first. Never touch components, pins, or connectors without the wrist strap attached and grounded.
Symbols on Equipment#
This is a universal recycling symbol indicating that the electronic device cannot be disposed of in the trash and must be recycled according to the regulations and/or ordinances of the local community.
Caution: this symbol indicates that the marked item can be hot and should not be touched without taking care.
General Precautions#
To reduce the risk of electric shock, personal injury, or damage to the equipment, observe the following precautions:
Follow all cautions and instructions marked on the equipment.
Do not eat, drink, or smoke while working with DGX Spark.
Do not bend, drop, crush, puncture, incinerate, or push objects into DGX Spark.
Do not connect or disconnect any cables or perform maintenance or reconfiguration of this product during an electrical storm or when the device is powered on.
Do not use DGX Spark in rain or near a sink or other wet locations. Take care not to spill any food or liquid into the device. If DGX Spark gets wet, unplug all cables and turn off before cleaning, and allow it to dry thoroughly before turning it on again.
Do not expose DGX Spark to any gas which is not normally contained in the atmosphere; it may cause defects.
Never turn on any equipment when there is evidence of fire, water, or structural damage.
Place the product away from radiators, heat registers, stoves, amplifiers, or other appliances that produce heat.
Never force a connector into a port. Check for obstructions on the port. If the connector and port do not join with reasonable ease, they probably do not match. Make sure that the connector matches the port and that you have positioned the connector correctly in relation to the port.
Always use an NVIDIA approved power adapter and refer to the manufacturer’s instructions or equipment manual for proper instructions. Do not connect or disconnect the AC power adapter with wet hands. The power adapter is intended for indoor use only.
DGX Spark shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Use only the provided AC adapter and power cord. Use of any other AC adapter or power cord may present risk of fire or electric shock.
Use certified Optical Fiber Transceiver Class I Laser Product.
Operate the AC adapter in a ventilated area.
When you are using DGX Spark, it is normal for the system and/or AC power adapter to get warm.
Do not use conductive tools that could bridge live parts.
Do not make mechanical or electrical modifications to the equipment.
Operate and store DGX Spark in a place where the temperature is always between 5 and 30°C (41 to 86°F).
Use this product only with approved equipment and/or accessories.
If the product sustains damage requiring service, disconnect the product from the AC electrical outlet and refer servicing to an NVIDIA authorized service provider.
This equipment is not suitable for use in locations where children are likely to be present.
For service personnel only:
CAUTION - Risk of fire or explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Power Rating#
48V ⎓ 5A
USB-C Ports Rating#
Each USB-C port can be loaded 5V/3A respectively. The total output power of USB-C ports is limited to 30W.
Compliance#
DGX Spark (Model: P4242) is compliant with the regulations listed in this section.
United States#
Federal Communications Commission (FCC)#
Contains FCC ID: RAS-MT7925B14L
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including any interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Warning: The FCC requires that you be notified that any changes or modifications to this device not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Only those antennas with same type and lesser/equal gain filed under this FCC ID number can be used with this device.
Transmitters in the 5.925-7.125 GHz band are prohibited from operating to control or communicate with unmanned aircraft systems.
RF Radiation Exposure Statement:
DGX Spark has been tested and complies with FCC RF radiation exposure limits set forth for an uncontrolled environment when used with the NVIDIA accessories supplied or designated for this product. During testing, DGX Spark was placed in positions that simulate use against the body. The use of any other accessories may not ensure compliance with FCC RF exposure guidelines.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter.
Underwriters Laboratories (UL)#
The product contains a non-replaceable coin battery, CR2032 with a nominal voltage of 3 Vdc. This battery is a non-rechargeable battery and must not be recharged.
Remove and immediately recycle or dispose of used batteries according to local regulations and keep them away from children. Do NOT dispose of batteries in household trash or incinerate them. Even used batteries may cause severe injury or death. Call a local poison control center for treatment information if needed.
Do not force discharge, recharge, disassemble, heat above the operating temperature, or incinerate batteries. Doing so may result in injury due to venting, leakage, or explosion, which can cause chemical burns.
Canada#
Innovation, Science and Economic Development Canada (ISED)#
Contains IC: 7542A-MT7925B14L
CAN ICES (B)/NMB (B)
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Caution:
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Be advised that high-power radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Operation in the band 5925-7125 MHz, the following restrictions must be met:
Devices shall not be used for control of or communications with unmanned aircraft systems.
Devices shall not be used on oil platforms.
Devices shall not be used on aircraft, except for the low-power indoor access points, indoor subordinate devices, low-power client devices, and very low-power devices operating in the 5925-6425 MHz band, that may be used on large aircraft as defined in the Canadian Aviation Regulations, while flying above 3,048 metres (10,000 feet).
Devices shall not be used on automobiles.
Devices shall not be used on trains.
Devices shall not be used on maritime vessels.
Attention:
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Être informé des radars à haute puissance sont alloués principaux utilisateurs de bandes 5250 à 5350 MHz et 5850 MHz, à 5650 et que ces radars pourraient provoquer des interférences et / ou endommager les appareils RL-EL.
Pour fonctionner dans la bande 5925-7125 MHz, les restrictions suivantes doivent être respectées:
Les dispositifs ne doivent pas être utilisés pour commander des systèmes d’aéronef sans pilote ni pour communiquer avec de tels systèmes.
Les dispositifs ne doivent pas être utilisés sur les plateformes de forage pétrolier.
Les dispositifs ne doivent pas être utilisés dans les aéronefs, à l’exception des points d’accès intérieurs de faible puissance, des dispositifs subordonnés intérieurs, des dispositifs clients de faible puissance et des dispositifs de très faible puissance fonctionnant dans la bande de 5925 à 6425 MHz, qui peuvent être utilisés dans les gros aéronefs, tel qu’il est défini dans le Règlement de l’aviation canadien, lorsqu’ils volent à une altitude supérieure à 3 048 mètres (10 000 pieds).
Les dispositifs ne doivent pas être utilisés dans les automobiles.
Les dispositifs ne doivent pas être utilisés dans les trains.
Les dispositifs ne doivent pas être utilisés sur les navires maritimes.
RF Radiation Exposure Statement:
DGX Spark has been tested and complies with IC RSS 102 RF radiation exposure limits set forth for an uncontrolled environment when used with the NVIDIA accessories supplied or designated for this product. During testing, the DGX Spark was placed in positions that simulate use against the body. The use of any other accessories may not ensure compliance with IC RSS 102 RF exposure guidelines.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Déclaration d’exposition aux radiations:
NVIDIA DGX Spark a ete testee conformemment aux normes d’exposition d’emission RF de la IC RSS 102 pour un environement non controle lors d’utilisation avec les accessoires fournis or recommendes par NVIDIA. Pendant les tests, le DGX Spark a ete positionne afin de simule la presence du corps humain. L’utilisation d’accessoires autres que ceux recommendes par NVIDIA ne guarantis pas la compatibilite avec les normes d’emission RF de la IC RSS 102.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
European Union#
European Conformity; Conformité Européenne (CE)#
This device complies with the following Directives:
Radio Equipment Directive 2014/53/EU
RoHS 2011/65/EU as amended by 2015/863/EU
Energy-related Products Directive (ErP) 2009/125/EC
The full text of Declaration of Conformity is available at the following internet address: http://www.nvidia.com/support
A copy of the Declaration of Conformity to the essential requirements may also be obtained directly from NVIDIA GmbH (Bavaria Towers – Blue Tower, Einsteinstrasse 172, D-81677 Munich Germany).
This device operates in the following frequency bands and maximum transmitted power:
Frequency Band |
Max. EIRP (dBm) |
Max. EIRP (mW) |
|---|---|---|
2400.0 - 2483.5 MHz |
20.0 |
100 |
5150.0 - 5350.0 MHz |
23.0 |
200 |
5470.0 – 5725.0 MHz |
23.0 |
200 |
5725.0 – 5875.0 MHz |
14.0 |
25 |
5925.0 – 6425.0 MHz (LPI mode) |
23.0 |
200 |
5925.0 – 6425.0 MHz (VLP mode) |
14.0 |
25 |
Warning:
Operation in the 5150 – 5350 MHz and 5925 – 6425 MHz (LPI mode) frequency bands are restricted to Indoor Use Only.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Any changes or modifications to this device not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Hardware version: 670-54242-0000
Firmware version: 5.36
Exposed services via network interfaces:
Port |
State |
Service |
|---|---|---|
22/tcp |
Open |
OpenSSH |
80/tcp |
Open |
HTTP |
Commission Regulation (EU) No 617/2013 Technical information#
DGX Spark, Model P4242, is classified as a small-scale server, and manufactured by NVIDIA Corporation (Santa Clara, CA, 95051, USA) in 2025.
This device is in compliance with (EU) No 617/2013.
Maximum Power (W) |
233.2 |
Idle State Power (W) |
38.0 |
Off Mode Power (W) |
4.1 |
Test methodology |
IEC 62623 / EN 62623 |
Test Voltage and Frequency |
230V / 50Hz |
Total Harmonic Distortion |
< 2% |
Noise Levels (per ECMA-74) |
Refer to DGX Spark support page |
External power supply efficiency (per EN50563) |
Level VI |
Great Britain (England, Wales and Scotland)#
UK Conformity Assessed#
Restrictions or Requirements for use in the UK#
This device complies with the following Regulations:
SI 2017/1206 Radio Equipment Regulations 2017
SI 2012/3032: The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (As Amended)
SI 2010/2617: The Ecodesign for Energy-Related Products Regulations 2010
The full text of Declaration of Conformity is available at the following internet address: http://www.nvidia.com/support
A copy of the Declaration of Conformity to the essential requirements may be obtained directly from NVIDIA Ltd. (100 Brook Drive, 3rd Floor Green Park, Reading RG2 6UJ, United Kingdom).
This device operates in the following frequency bands and maximum transmitted power:
Frequency Band |
Max. EIRP (dBm) |
Max. EIRP (mW) |
|---|---|---|
2400.0 - 2483.5 MHz |
20.0 |
100 |
5150.0 - 5350.0 MHz |
23.0 |
200 |
5470.0 – 5725.0 MHz |
23.0 |
200 |
5725.0 – 5875.0 MHz |
14.0 |
25 |
5925.0 – 6425.0 MHz (LPI mode) |
23.0 |
200 |
5925.0 – 6425.0 MHz (VLP mode) |
14.0 |
25 |
Warning:
Operation of this device in the 5150 - 5350 MHz and 5925 – 6425 MHz (LPI mode) frequency bands are restricted to indoor use.
This equipment must be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Any modifications to this device, not expressly approved by the manufacturer, voids the user authority to operate the equipment.
Australia and New Zealand#
Australian Communications and Media Authority#
This product meets the applicable EMC requirements for Class B, I.T.E equipment and applicable radio equipment requirements.
This product meets the applicable requirements for telecommunications equipment and can legally be connected to a telecommunications network.
Japan#
Voluntary Control Council for Interference (VCCI)#
Radio/Telecommunications Certification#
5.2GHz, 5.3GHz 及び 6GHz 帯 (LPI): 屋内使用限定
当該機器には電波法に基づく、技術基準適合証明等を受けた特定無線設備を装着している
Japan RoHS Material Content Declaration#
China#
China Compulsory Certificate#
State Radio Regulation of China (SRRC)#
CMIIT ID: 25J99Y4B4242
China RoHS Material Content Declaration#
South Korea#
Korea Certification (KC)#
Korea RoHS Material Content Declaration#
Taiwan#
Bureau of Standards, Metrology & Inspection (BSMI)#
This device complies with CNS 13438 (2006) Class B
報驗義務人：香港商輝達香港控股有限公司臺灣分公司 統一編號：80022300
地址：臺北市內湖區基湖路 8 號
Taiwan RoHS Material Content Declaration#
National Communications Commission#
注意！
依據 低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
在 5.250~5.350GHz 頻帶內操作之無線資訊傳輸設備，限於室內使用
應避免影響附近雷達系統之操作。
India#
Bureau of Indian Standards (BIS)#
Self Declaration - Conforming to IS 13252:2010, R-41315486
Authenticity may be verified by visiting the Bureau of Indian Standards website at http://www.bis.gov.in
India RoHS compliance statement#
This product, as well as its related consumables and spares, complies with the reduction in hazardous substances provisions of the “India E-waste (Management and Handling) Rule 2016”. It does not contain lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for where allowed pursuant to the exemptions set in Schedule 2 of the Rule.
Wireless Planning & Coordination Wing (WPC)#
Registration No.: ETA-SD-20250807136
Singapore#
Malaysia#
Malaysian Communications and Multimedia Commission (MCMC)#
Bluetooth#
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by NVIDIA Corporation is under license. Other trademarks and trade names are those of their respective owners.