6.19. Event Management

This section describes the event management functions of the low-level CUDA driver application programming interface.

Functions

CUresult cuEventCreate ( CUevent* phEvent, unsigned int  Flags )
Creates an event.
CUresult cuEventDestroy ( CUevent hEvent )
Destroys an event.
CUresult cuEventElapsedTime ( float* pMilliseconds, CUevent hStart, CUevent hEnd )
Computes the elapsed time between two events.
CUresult cuEventQuery ( CUevent hEvent )
Queries an event's status.
CUresult cuEventRecord ( CUevent hEvent, CUstream hStream )
Records an event.
CUresult cuEventRecordWithFlags ( CUevent hEvent, CUstream hStream, unsigned int  flags )
Records an event.
CUresult cuEventSynchronize ( CUevent hEvent )
Waits for an event to complete.

Functions

CUresult cuEventCreate ( CUevent* phEvent, unsigned int  Flags )
Creates an event.
Parameters
phEvent
- Returns newly created event
Flags
- Event creation flags
Description

Creates an event *phEvent for the current context with the flags specified via Flags. Valid flags include:

Note:

Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventRecord, cuEventQuery, cuEventSynchronize, cuEventDestroy, cuEventElapsedTime, cudaEventCreate, cudaEventCreateWithFlags

CUresult cuEventDestroy ( CUevent hEvent )
Destroys an event.
Parameters
hEvent
- Event to destroy
Description

Destroys the event specified by hEvent.

An event may be destroyed before it is complete (i.e., while cuEventQuery() would return CUDA_ERROR_NOT_READY). In this case, the call does not block on completion of the event, and any associated resources will automatically be released asynchronously at completion.

Note:

Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventCreate, cuEventRecord, cuEventQuery, cuEventSynchronize, cuEventElapsedTime, cudaEventDestroy

CUresult cuEventElapsedTime ( float* pMilliseconds, CUevent hStart, CUevent hEnd )
Computes the elapsed time between two events.
Parameters
pMilliseconds
- Time between hStart and hEnd in ms
hStart
- Starting event
hEnd
- Ending event
Description

Computes the elapsed time between two events (in milliseconds with a resolution of around 0.5 microseconds).

If either event was last recorded in a non-NULL stream, the resulting time may be greater than expected (even if both used the same stream handle). This happens because the cuEventRecord() operation takes place asynchronously and there is no guarantee that the measured latency is actually just between the two events. Any number of other different stream operations could execute in between the two measured events, thus altering the timing in a significant way.

If cuEventRecord() has not been called on either event then CUDA_ERROR_INVALID_HANDLE is returned. If cuEventRecord() has been called on both events but one or both of them has not yet been completed (that is, cuEventQuery() would return CUDA_ERROR_NOT_READY on at least one of the events), CUDA_ERROR_NOT_READY is returned. If either event was created with the CU_EVENT_DISABLE_TIMING flag, then this function will return CUDA_ERROR_INVALID_HANDLE.

Note:

Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventCreate, cuEventRecord, cuEventQuery, cuEventSynchronize, cuEventDestroy, cudaEventElapsedTime

CUresult cuEventQuery ( CUevent hEvent )
Queries an event's status.
Parameters
hEvent
- Event to query
Description

Queries the status of all work currently captured by hEvent. See cuEventRecord() for details on what is captured by an event.

Returns CUDA_SUCCESS if all captured work has been completed, or CUDA_ERROR_NOT_READY if any captured work is incomplete.

For the purposes of Unified Memory, a return value of CUDA_SUCCESS is equivalent to having called cuEventSynchronize().

Note:

Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventCreate, cuEventRecord, cuEventSynchronize, cuEventDestroy, cuEventElapsedTime, cudaEventQuery

CUresult cuEventRecord ( CUevent hEvent, CUstream hStream )
Records an event.
Parameters
hEvent
- Event to record
hStream
- Stream to record event for
Description

Captures in hEvent the contents of hStream at the time of this call. hEvent and hStream must be from the same context otherwise CUDA_ERROR_INVALID_HANDLE is returned. Calls such as cuEventQuery() or cuStreamWaitEvent() will then examine or wait for completion of the work that was captured. Uses of hStream after this call do not modify hEvent. See note on default stream behavior for what is captured in the default case.

cuEventRecord() can be called multiple times on the same event and will overwrite the previously captured state. Other APIs such as cuStreamWaitEvent() use the most recently captured state at the time of the API call, and are not affected by later calls to cuEventRecord(). Before the first call to cuEventRecord(), an event represents an empty set of work, so for example cuEventQuery() would return CUDA_SUCCESS.

Note:
  • This function uses standard default stream semantics.

  • Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventCreate, cuEventQuery, cuEventSynchronize, cuStreamWaitEvent, cuEventDestroy, cuEventElapsedTime, cudaEventRecord, cuEventRecordWithFlags

CUresult cuEventRecordWithFlags ( CUevent hEvent, CUstream hStream, unsigned int  flags )
Records an event.
Parameters
hEvent
- Event to record
hStream
- Stream to record event for
flags
- See CUevent_capture_flags
Description

Captures in hEvent the contents of hStream at the time of this call. hEvent and hStream must be from the same context otherwise CUDA_ERROR_INVALID_HANDLE is returned. Calls such as cuEventQuery() or cuStreamWaitEvent() will then examine or wait for completion of the work that was captured. Uses of hStream after this call do not modify hEvent. See note on default stream behavior for what is captured in the default case.

cuEventRecordWithFlags() can be called multiple times on the same event and will overwrite the previously captured state. Other APIs such as cuStreamWaitEvent() use the most recently captured state at the time of the API call, and are not affected by later calls to cuEventRecordWithFlags(). Before the first call to cuEventRecordWithFlags(), an event represents an empty set of work, so for example cuEventQuery() would return CUDA_SUCCESS.

flags include:

Note:
  • This function uses standard default stream semantics.

  • Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventCreate, cuEventQuery, cuEventSynchronize, cuStreamWaitEvent, cuEventDestroy, cuEventElapsedTime, cuEventRecord, cudaEventRecord

CUresult cuEventSynchronize ( CUevent hEvent )
Waits for an event to complete.
Parameters
hEvent
- Event to wait for
Description

Waits until the completion of all work currently captured in hEvent. See cuEventRecord() for details on what is captured by an event.

Waiting for an event that was created with the CU_EVENT_BLOCKING_SYNC flag will cause the calling CPU thread to block until the event has been completed by the device. If the CU_EVENT_BLOCKING_SYNC flag has not been set, then the CPU thread will busy-wait until the event has been completed by the device.

Note:

Note that this function may also return error codes from previous, asynchronous launches.

See also:

cuEventCreate, cuEventRecord, cuEventQuery, cuEventDestroy, cuEventElapsedTime, cudaEventSynchronize